I also am trying to use my ATEM Ethernet USB
Adaptor.
I am now applying Micheal's kaweth driver
0.2.1(thank you). But I failed to recognize.
Here is a output of dmesg and contents of
/proc/bus/usb/devices
Any suggestions are welcome.
Thanks.
Hisashi
PS.
In my environment, order of 'insmod', pluggin device
does not have any effect to recognition.
---------------------------
Envirionment Kernel 2.2.14 + backport patch usb-2.3.99-pre7-1-for-2.2.14.diff.gz
output of dmesg(only related parts)
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.228 $ time 23:03:48 May 12 2000
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: Intel USB controller: setting latency timer to 0
usb-uhci.c: USB UHCI at I/O 0xfce0, IRQ 10
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
usb.c: USB new device connect, assigned device number 1
usb.c: kmalloc IF c0e0bb20, numif 1
usb.c: new device strings: Mfr=0, Product=2, SerialNumber=1
usb.c: USB device number 1 default language ID 0x0
Product: USB UHCI Root Hub
SerialNumber: fce0
hub.c: USB hub found
hub.c: 2 ports detected
hub.c: ganged power switching
hub.c: standalone hub
hub.c: global over-current protection
hub.c: power on to power good time: 2ms
hub.c: hub controller current requirement: 0mA
hub.c: port 1 is removable
hub.c: port 2 is removable
hub.c: local power source is good
hub.c: no over-current condition exists
hub.c: enabling power on all ports
usb.c: hub driver claimed interface c0e0bb20
Kawasaki USB->Ethernet Driver loading...
usb.c: registered new driver kaweth
usb.c: registered new driver hid
mice: PS/2 mouse device common for all mice
usb.c: registered new driver usblp
registered device ppp0
hub.c: port 1 connection change
hub.c: portstatus 101, change 1, High Speed
hub.c: portstatus 103, change 0, High Speed
usb.c: USB new device connect, assigned device number 2
usb.c: kmalloc IF c2c0a3c0, numif 1
usb.c: new device strings: Mfr=2, Product=3, SerialNumber=1
usb.c: USB device number 2 default language ID 0x409
Manufacturer: ATEN Inc.
Product: USB-Ethernet
SerialNumber: 001074003548
usb-uhci.c: interrupt, status 2, frame# 1844
Kawasaki Device Probe (Device number:2): 0x0557:0x2002
Device at c1871b40
Descriptor length: 12 type: 1
D-Link DSB-650 connected...
Reading kaweth configuration
Request type: c0 Request: 0 Value: 0 Index: 0 Length: 12
usb-uhci.c: interrupt, status 2, frame# 1846
usb-uhci-debug.h: TD @ c0d4b8e0/00D4B8E0, MaxLen=07 DT0 EP=0 Dev=2 PID=(SETUP)
buf=024d0440
usb-uhci-debug.h: Len=07 e0 Stalled CRC/Timeo
usb-uhci-debug.h: Link points to TD @ 00d4b9e0, Breadth first
kaweth control message failed (urb addr: c0f97d20)
usb-uhci.c: interrupt, status 2, frame# 1849
usb-uhci-debug.h: TD @ c0d4b860/00D4B860, MaxLen=07 DT0 EP=0 Dev=2 PID=(SETUP)
buf=024d0680
usb-uhci-debug.h: Len=07 e0 SPD Stalled CRC/Timeo
usb-uhci-debug.h: Link points to TD @ 00d4ba20, Breadth first
usb-uhci.c: interrupt, status 2, frame# 1851
usb-uhci-debug.h: TD @ c0d4b960/00D4B960, MaxLen=07 DT0 EP=0 Dev=2 PID=(SETUP)
buf=024d0680
usb-uhci-debug.h: Len=07 e0 SPD Stalled CRC/Timeo
usb-uhci-debug.h: Link points to TD @ 00d4b7e0, Breadth first
Actual length: 0, length 18
Resetting...
usb-uhci.c: interrupt, status 2, frame# 1854
usb-uhci-debug.h: TD @ c0d4ba20/00D4BA20, MaxLen=07 DT0 EP=0 Dev=2 PID=(SETUP)
buf=024d0440
usb-uhci-debug.h: Len=07 e0 SPD Stalled CRC/Timeo
usb-uhci-debug.h: Link points to TD @ 00d4b860, Breadth first
Downloading firmware at c38a4ab8 to kaweth device at c1794000...
Firmware length: 3838
Request type: 40 Request: ff Value: 0 Index: 0 Length: efe
usb-uhci.c: interrupt, status 2, frame# 1868
usb-uhci-debug.h: TD @ c0d4b7e0/00D4B7E0, MaxLen=07 DT0 EP=0 Dev=2 PID=(SETUP)
buf=024d0440
usb-uhci-debug.h: Len=07 e0 Stalled CRC/Timeo
usb-uhci-debug.h: Link points to TD @ 00d4b960, Breadth first
kaweth control message failed (urb addr: c0f97d20)
usb-uhci.c: interrupt, status 2, frame# 1870
usb-uhci-debug.h: TD @ c0d4b860/00D4B860, MaxLen=07 DT0 EP=0 Dev=2 PID=(SETUP)
buf=024d0680
usb-uhci-debug.h: Len=07 e0 SPD Stalled CRC/Timeo
usb-uhci-debug.h: Link points to TD @ 00d4ba20, Breadth first
usb-uhci.c: interrupt, status 2, frame# 1873
usb-uhci-debug.h: TD @ c0d4bfa0/00D4BFA0, MaxLen=07 DT0 EP=0 Dev=2 PID=(SETUP)
buf=024d0680
usb-uhci-debug.h: Len=07 e0 SPD Stalled CRC/Timeo
usb-uhci-debug.h: Link points to TD @ 00d4bf60, Breadth first
Actual length: 0, length 3838
Error downloading firmware (-110), no net device created
usb.c: unhandled interfaces on device
usb.c: This device is not recognized by any installed USB driver.
Length = 18
DescriptorType = 01
USB version = 1.00
Vendor:Product = 0557:2002
MaxPacketSize0 = 8
NumConfigurations = 1
Device version = 0.02
Device Class:SubClass:Protocol = 00:00:00
Per-interface classes
Configuration:
bLength = 9
bDescriptorType = 02
wTotalLength = 0027
bNumInterfaces = 01
bConfigurationValue = 01
iConfiguration = 00
bmAttributes = 80
MaxPower = 90mA
Interface: 0
Alternate Setting: 0
bLength = 9
bDescriptorType = 04
bInterfaceNumber = 00
bAlternateSetting = 00
bNumEndpoints = 03
bInterface Class:SubClass:Protocol = 00:00:00
iInterface = 00
Endpoint:
bLength = 7
bDescriptorType = 05
bEndpointAddress = 81 (in)
bmAttributes = 02 (Bulk)
wMaxPacketSize = 0040
bInterval = 00
Endpoint:
bLength = 7
bDescriptorType = 05
bEndpointAddress = 02 (out)
bmAttributes = 02 (Bulk)
wMaxPacketSize = 0040
bInterval = 00
Endpoint:
bLength = 7
bDescriptorType = 05
bEndpointAddress = 83 (in)
bmAttributes = 03 (Interrupt)
wMaxPacketSize = 0008
bInterval = 01
---------------------------------------------------------
contents of /proc/bus/usb/devices
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.00 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 0.00
S: Product=USB UHCI Root Hub
S: SerialNumber=fce0
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=255ms
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 1.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0557 ProdID=2002 Rev= 0.02
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr= 90mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=00(>ifc ) Sub=00 Prot=00 Driver=(none)
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl= 0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl= 0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 8 Ivl= 1ms
--
---------------------------------
Hashimoto Hisashi(Hitachi@HP NJL)
[EMAIL PROTECTED]
---------------------------------
---------------------------------------------------------------------
To unsubscribe, e-mail: [EMAIL PROTECTED]
For additional commands, e-mail: [EMAIL PROTECTED]
- Re: [linux-usb] ATEN Ethernet hashimoh
