On 09/11/2012 04:06 AM, Kuninori Morimoto wrote: > This patch adds Renesas R-Car USB phy driver. > It supports R8A7779 chip at this point. > > R-Car has some USB controllers, but has only one phy-initializer. > So, this driver is counting users. > > Signed-off-by: Kuninori Morimoto <[email protected]> > --- > v3 -> v4 > > - rcar_usb_phy_shutdown() became static > - used priv->counter == x > - removed dev_info() > - MODULE_LICENSE("GPL v2") > > drivers/usb/phy/Kconfig | 12 +++ > drivers/usb/phy/Makefile | 1 + > drivers/usb/phy/rcar-phy.c | 225 > ++++++++++++++++++++++++++++++++++++++++++++ > 3 files changed, 238 insertions(+) > create mode 100644 drivers/usb/phy/rcar-phy.c > > diff --git a/drivers/usb/phy/Kconfig b/drivers/usb/phy/Kconfig > index 63c339b..7eb73c5 100644 > --- a/drivers/usb/phy/Kconfig > +++ b/drivers/usb/phy/Kconfig > @@ -32,3 +32,15 @@ config MV_U3D_PHY > help > Enable this to support Marvell USB 3.0 phy controller for Marvell > SoC. > + > +config USB_RCAR_PHY > + tristate "Renesas R-Car USB phy support" > + depends on USB || USB_GADGET > + select USB_OTG_UTILS > + help > + Say Y here to add support for the Renesas R-Car USB phy driver. > + This chip is typically used as USB phy for USB host, gadget. > + This driver supports: R8A7779 > + > + To compile this driver as a module, choose M here: the > + module will be called rcar-phy. > diff --git a/drivers/usb/phy/Makefile b/drivers/usb/phy/Makefile > index b069f29..1a579a8 100644 > --- a/drivers/usb/phy/Makefile > +++ b/drivers/usb/phy/Makefile > @@ -8,3 +8,4 @@ obj-$(CONFIG_OMAP_USB2) += omap-usb2.o > obj-$(CONFIG_USB_ISP1301) += isp1301.o > obj-$(CONFIG_MV_U3D_PHY) += mv_u3d_phy.o > obj-$(CONFIG_USB_EHCI_TEGRA) += tegra_usb_phy.o > +obj-$(CONFIG_USB_RCAR_PHY) += rcar-phy.o > diff --git a/drivers/usb/phy/rcar-phy.c b/drivers/usb/phy/rcar-phy.c > new file mode 100644 > index 0000000..3fce889 > --- /dev/null > +++ b/drivers/usb/phy/rcar-phy.c > @@ -0,0 +1,225 @@ > +/* > + * Renesas R-Car USB phy driver > + * > + * Copyright (C) 2012 Renesas Solutions Corp. > + * Kuninori Morimoto <[email protected]> > + * > + > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License version 2 as > + * published by the Free Software Foundation. > + */ > + > +#include <linux/delay.h> > +#include <linux/io.h> > +#include <linux/usb/otg.h> > +#include <linux/platform_device.h> > +#include <linux/spinlock.h> > +#include <linux/module.h> > + > +/* USBH common register */ > +#define USBPCTRL0 0x0800 > +#define USBPCTRL1 0x0804 > +#define USBST 0x0808 > +#define USBEH0 0x080C > +#define USBOH0 0x081C > +#define USBCTL0 0x0858 > +#define EIIBC1 0x0094 > +#define EIIBC2 0x009C > + > +#ifdef CONFIG_ARCH_SUPPORTS_BIG_ENDIAN
That symbol is only defined on ARM's mach-ixp4xx. If you want to support
big endian hosts in general, you have to use a different symbol.
> +# define PHY_ENDIAN "BIG"
^^^^^^^^^^
It this used?
> +# define PHY_NO_SWAP 0x00000003
> +#else
> +# define PHY_ENDIAN "LITTLE"
> +# define PHY_NO_SWAP 0x00000000
> +#endif
> +
> +/* USBPCTRL1 */
> +#define PHY_RST (1 << 2)
> +#define PLL_ENB (1 << 1)
> +#define PHY_ENB (1 << 0)
> +
> +/* USBST */
> +#define ACT (1 << 31)
> +#define PLL (1 << 30)
> +
> +struct rcar_usb_phy_priv {
> + struct usb_phy phy;
> + spinlock_t lock;
> +
> + void __iomem *reg0;
> + void __iomem *reg1;
> + int counter;
> +};
> +
> +#define usb_phy_to_priv(p) container_of(p, struct rcar_usb_phy_priv, phy)
> +
> +
> +/*
> + * USB initial/install operation.
> + *
> + * This function setup USB phy.
> + * The used value and setting order came from
> + * [USB :: Initial setting] on datasheet.
> + */
> +static int rcar_usb_phy_init(struct usb_phy *phy)
> +{
> + struct rcar_usb_phy_priv *priv = usb_phy_to_priv(phy);
> + struct device *dev = phy->dev;
> + void __iomem *reg0 = priv->reg0;
> + void __iomem *reg1 = priv->reg1;
> + int i;
> + u32 val;
> + unsigned long flags;
> +
> + spin_lock_irqsave(&priv->lock, flags);
> + if (priv->counter == 0) {
> +
> + /*
> + * USB phy start-up
> + */
> +
> + /* (1) USB-PHY standby release */
> + iowrite32(PHY_ENB, (reg0 + USBPCTRL1));
> +
> + /* (2) start USB-PHY internal PLL */
> + iowrite32(PHY_ENB | PLL_ENB, (reg0 + USBPCTRL1));
> +
> + /* (3) USB module status check */
> + for (i = 0; i < 1024; i++) {
> + udelay(10);
> + val = ioread32(reg0 + USBST);
> + if ((ACT | PLL) == val)
nitpick:
It' more common to write the comparison the other way round:
if (val == (ACT | PLL))
The compiler will warn you, if you do an assignment instead of a comparison.
> + break;
> + }
> +
> + if ((ACT | PLL) != val) {
> + dev_err(dev, "USB phy not ready\n");
> + goto phy_init_end;
> + }
> +
> + /* (4) USB-PHY reset clear */
> + iowrite32(PHY_ENB | PLL_ENB | PHY_RST, (reg0 + USBPCTRL1));
> +
> + /* set platform specific port settings */
> + iowrite32(0x00000000, (reg0 + USBPCTRL0));
> +
> + /*
> + * EHCI IP internal buffer setting
> + * EHCI IP internal buffer enable
> + *
> + * These are recommended value of a datasheet
> + * see [USB :: EHCI internal buffer setting]
> + */
> + iowrite32(0x00ff0040, (reg0 + EIIBC1));
> + iowrite32(0x00ff0040, (reg1 + EIIBC1));
> +
> + iowrite32(0x00000001, (reg0 + EIIBC2));
> + iowrite32(0x00000001, (reg1 + EIIBC2));
> +
> + /*
> + * Bus alignment settings
> + */
> +
> + /* (1) EHCI bus alignment */
> + iowrite32(PHY_NO_SWAP, (reg0 + USBEH0));
> +
> + /* (1) OHCI bus alignment */
> + iowrite32(PHY_NO_SWAP, (reg0 + USBOH0));
> + }
> + priv->counter++;
> +
> +phy_init_end:
> + spin_unlock_irqrestore(&priv->lock, flags);
> +
> + return 0;
> +}
> +
> +static void rcar_usb_phy_shutdown(struct usb_phy *phy)
> +{
> + struct rcar_usb_phy_priv *priv = usb_phy_to_priv(phy);
> + void __iomem *reg0 = priv->reg0;
> + unsigned long flags;
> +
> + spin_lock_irqsave(&priv->lock, flags);
> +
> + if (priv->counter == 1) { /* last user */
> + iowrite32(0x00000000, (reg0 + USBPCTRL0));
> + iowrite32(0x00000000, (reg0 + USBPCTRL1));
> + }
> + priv->counter--;
> +
> + spin_unlock_irqrestore(&priv->lock, flags);
> +}
> +
> +static int __devinit rcar_usb_phy_probe(struct platform_device *pdev)
> +{
> + struct rcar_usb_phy_priv *priv;
> + struct resource *res0, *res1;
> + struct device *dev = &pdev->dev;
> + void __iomem *reg0, *reg1;
> + int ret;
> +
> + res0 = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + res1 = platform_get_resource(pdev, IORESOURCE_MEM, 1);
> + if (!res0 || !res1) {
> + dev_err(dev, "Not enough platform resources\n");
> + return -EINVAL;
> + }
> +
> + reg0 = devm_ioremap_nocache(dev, res0->start, resource_size(res0));
> + reg1 = devm_ioremap_nocache(dev, res1->start, resource_size(res1));
> + if (!reg0 || !reg1) {
> + dev_err(dev, "ioremap error\n");
> + return -ENOMEM;
> + }
> +
> + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
> + if (!priv) {
> + dev_err(dev, "priv data allocation error\n");
> + return -ENOMEM;
> + }
> +
> + priv->reg0 = reg0;
> + priv->reg1 = reg1;
> + priv->counter = 0;
> + priv->phy.dev = dev;
> + priv->phy.label = dev_name(dev);
> + priv->phy.init = rcar_usb_phy_init;
> + priv->phy.shutdown = rcar_usb_phy_shutdown;
> + spin_lock_init(&priv->lock);
> +
> + ret = usb_add_phy(&priv->phy, USB_PHY_TYPE_USB2);
> + if (ret < 0) {
> + dev_err(dev, "usb phy addition error\n");
> + return ret;
> + }
> +
> + platform_set_drvdata(pdev, priv);
> +
> + return ret;
> +}
> +
> +static int __exit rcar_usb_phy_remove(struct platform_device *pdev)
> +{
> + struct rcar_usb_phy_priv *priv = platform_get_drvdata(pdev);
> +
> + usb_remove_phy(&priv->phy);
> +
> + return 0;
> +}
> +
> +static struct platform_driver rcar_usb_phy_driver = {
> + .driver = {
> + .name = "rcar_usb_phy",
> + },
> + .probe = rcar_usb_phy_probe,
> + .remove = __devexit_p(rcar_usb_phy_remove),
> +};
> +
> +module_platform_driver(rcar_usb_phy_driver);
> +
> +MODULE_LICENSE("GPL v2");
> +MODULE_DESCRIPTION("Renesas R-Car USB phy");
> +MODULE_AUTHOR("Kuninori Morimoto <[email protected]>");
>
Marc
--
Pengutronix e.K. | Marc Kleine-Budde |
Industrial Linux Solutions | Phone: +49-231-2826-924 |
Vertretung West/Dortmund | Fax: +49-5121-206917-5555 |
Amtsgericht Hildesheim, HRA 2686 | http://www.pengutronix.de |
signature.asc
Description: OpenPGP digital signature
