Keith Antoine wrote:
I have found something else: when I try cdrecord --scanbus after connecting and disconnecting the camera it locks up, freezing the terminal. I am using a cd-rw as ide-scsi and I also have a dvd (not ide-scsi). Maybe there is a conflict?On Friday 15 November 2002 08:45 pm, Ken Moffat espoused:I did modprobe usb-storage. Doesn't seeem to work, but I'm sure it's me being bone-headed. Sometimes the camera shows up in usbview, but I can't figure what to mount. Here is what I see in usbview:
What shows up in dmesg re the usb mass storage, and is it assigned a driver i /dev?
Early in dmesg is the following:
usb-uhci.c: interrupt, status 2, frame# 584
usb-uhci.c: interrupt, status 2, frame# 19
usb-uhci.c: interrupt, status 2, frame# 1172
usb-uhci.c: interrupt, status 2, frame# 1438
usbdevfs: USBDEVFS_CONTROL failed dev 2 rqt 128 rq 6 len 256 ret -84
usbdevfs: USBDEVFS_CONTROL failed dev 2 rqt 128 rq 6 len 256 ret -84
usbdevfs: USBDEVFS_CONTROL failed dev 2 rqt 128 rq 6 len 256 ret -84
usbdevfs: USBDEVFS_CONTROL failed dev 2 rqt 128 rq 6 len 9 ret -84
usbdevfs: USBDEVFS_CONTROL failed dev 2 rqt 128 rq 6 len 256 ret -84
usb-uhci.c: interrupt, status 2, frame# 704
usbdevfs: USBDEVFS_CONTROL failed dev 2 rqt 128 rq 6 len 256 ret -84
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <[EMAIL PROTECTED]>
hid-core.c: USB HID support drivers
Further down is:
SCSI subsystem driver Revision: 1.00
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
Later is a mess:
hub.c: USB new device connect on bus3/1, assigned device number 2
scsi1 : SCSI emulation for USB Mass Storage devices
resize_dma_pool: unknown device type -1
usb-uhci.c: interrupt, status 3, frame# 95
i2c-core.o: i2c core module
i2c-algo-bit.o: i2c bit algorithm module
Linux video capture interface: v1.00
bttv: driver version 0.7.91 loaded
bttv: using 2 buffers with 2080k (4160k total) for capture
bttv: Host bridge is VIA Technologies, Inc. VT8367 [KT266]
usb-uhci.c: interrupt, status 2, frame# 584
usb-uhci.c: interrupt, status 2, frame# 19
usb-uhci.c: interrupt, status 2, frame# 1172
usb-uhci.c: interrupt, status 2, frame# 1438
usbdevfs: USBDEVFS_CONTROL failed dev 2 rqt 128 rq 6 len 256 ret -84
usbdevfs: USBDEVFS_CONTROL failed dev 2 rqt 128 rq 6 len 256 ret -84
usbdevfs: USBDEVFS_CONTROL failed dev 2 rqt 128 rq 6 len 256 ret -84
usbdevfs: USBDEVFS_CONTROL failed dev 2 rqt 128 rq 6 len 9 ret -84
usbdevfs: USBDEVFS_CONTROL failed dev 2 rqt 128 rq 6 len 256 ret -84
usb-uhci.c: interrupt, status 2, frame# 704
[this continues for a while with different frame numbers]
Then this:
Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0, type -1
resize_dma_pool: unknown device type -1
Thanks!
--
Ken Moffat
_______________________________________________
Linux-users mailing list
[EMAIL PROTECTED]
Unsubscribe/Suspend/Etc -> http://www.linux-sxs.org/mailman/listinfo/linux-users
