And for those common things, I guess some of them might be included by our
rootfs build system.
sense to locate these fragments there, and to factor out some common
configs. I see some of the issues I'm pointing out here are in the
existing fragments as well, so there's an opportunity for some low
effort fixups.
+
+CONFIG_PCI=y
+CONFIG_PCI_MSI=y
+CONFIG_PCI_MSI_IRQ_DOMAIN=y
+CONFIG_PCIE_XILINX_NWL=y
+CONFIG_PCIEPORTBUS=y
+CONFIG_PCIE_XDMA_PL=y
+
+#CPU ilde and freq
+CONFIG_CPU_IDLE=y
+CONFIG_ARM_CPUIDLE=y
+CONFIG_CPU_FREQ=y
+CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE=y
+CONFIG_CPU_FREQ_GOV_USERSPACE=y
+CONFIG_CPUFREQ_DT=y
+CONFIG_CPUFREQ_DT_PLATDEV=y
These are also not tied to h/w. We already have a
features/power/intel.cfg fragment. Can you relocate these to a zynqmp
or xilinx fragment and put it along side of the existing ones ?
I'll try it with a nice way.
+
+# CAN Device Drivers
+#
+CONFIG_CAN=y
+CONFIG_CAN_DEV=y
+CONFIG_CAN_XILINXCAN=y
+
+CONFIG_MTD=y
+CONFIG_MTD_OF_PARTS=y
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_M25P80=y
+CONFIG_MTD_SPI_NOR=y
+# CONFIG_JFFS2_FS_WRITEBUFFER is not set
+# CONFIG_MTD_SPI_NOR_USE_4K_SECTORS is not set
+
+CONFIG_BLK_DEV_SD=y
+CONFIG_ATA=y
+CONFIG_SATA_AHCI=y
+CONFIG_AHCI_CEVA=y
+CONFIG_NETDEVICES=y
+
+CONFIG_OF=y
+CONFIG_OF_MDIO=y
+CONFIG_ETHERNET=y
+CONFIG_NET_CADENCE=y
+CONFIG_MACB=y
+CONFIG_MACB_EXT_BD=y
+
+CONFIG_PHYLIB=y
+CONFIG_XILINX_PHY=y
+
+CONFIG_PHY_XILINX_ZYNQMP=y
+CONFIG_FIXED_PHY=y
+CONFIG_DEVMEM=y
+
+CONFIG_SERIAL_EARLYCON=y
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_SERIAL_XILINX_PS_UART=y
+CONFIG_SERIAL_XILINX_PS_UART_CONSOLE=y
+#
+CONFIG_I2C=y
+CONFIG_I2C_MUX=y
+CONFIG_I2C_MUX_PCA954x=y
+CONFIG_I2C_MUX_REG
+CONFIG_I2C_CADENCE=y
+CONFIG_I2C_XILINX=y
+CONFIG_EEPROM_AT24=y
+
+
+CONFIG_SPI=y
+CONFIG_SPI_MASTER=y
+CONFIG_SPI_CADENCE=y
+CONFIG_SPI_XILINX=y
+CONFIG_SPI_ZYNQMP_GQSPI=y
+
+CONFIG_GPIOLIB=y
+CONFIG_GPIO_DEVRES=y
+CONFIG_OF_GPIO=y
+CONFIG_GPIO_SYSFS=y
+CONFIG_GPIO_XILINX=y
+CONFIG_GPIO_PCA953X=y
+CONFIG_GPIO_PCA953X_IRQ=y
+CONFIG_GPIO_ZYNQ=y
+
+CONFIG_POWER_RESET=y
+CONFIG_SENSORS_INA2XX=y
+CONFIG_WATCHDOG=y
+CONFIG_CADENCE_WATCHDOG=y
+CONFIG_XILINX_WATCHDOG=y
+
+CONFIG_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_DWC3=y
+CONFIG_USB_DWC3_OF_SIMPLE=y
+CONFIG_USB_OTG=y
+CONFIG_USB_OTG_FSM=m
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_XILINX=y
+CONFIG_USB_ETH=m
+CONFIG_USB_MASS_STORAGE=m
bsp/xilinx/soc/drivers-zynq.cfg has some of these already. Can we
update and then include that fragment ?
This is a nasty cfg. I think you don't want to use it. But we can
remove them since we have already include usb-mass-storage.scc
+
+CONFIG_MMC=y
+CONFIG_MMC_BLOCK=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_PLTFM=y
+CONFIG_MMC_SDHCI_OF_ARASAN=y
+
+CONFIG_EDAC=y
+CONFIG_EDAC_MM_EDAC=y
+CONFIG_EDAC_SYNOPSYS=y
+CONFIG_EDAC_ZYNQMP_OCM=y
+
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_HCTOSYS=y
+CONFIG_RTC_HCTOSYS_DEVICE="rtc0"
+CONFIG_RTC_INTF_SYSFS=y
+CONFIG_RTC_DRV_ZYNQMP=y
+
+CONFIG_DMADEVICES=y
+CONFIG_DMA_ENGINE=y
+CONFIG_DMA_OF=y
+CONFIG_CMA=y
+CONFIG_DMA_CMA=y
+CONFIG_CMA_SIZE_MBYTES=256
Similar to my USB comment, I'm seeing some of this in existing
fragments, can we update those fragments and then just include them ?
En, I'll clean of them, some of them are redundant. But I'll keep
CONFIG_DMA_CMA=y since:
grep -rni 'CONFIG_DMA_CMA=y' ./
./bsp/beaglebone/beaglebone.cfg:47:CONFIG_DMA_CMA=y
./bsp/xilinx-zynqmp/xilinx-zynqmp.cfg:140:CONFIG_DMA_CMA=y
./bsp/intel-x86/intel-x86.cfg:319:CONFIG_DMA_CMA=y
+
+CONFIG_XILINX_AXIDMA=y
+CONFIG_XILINX_AXICDMA=y
+CONFIG_XILINX_ZYNQMP_DMA=y
+CONFIG_XILINX_DMA=y
+
+CONFIG_UIO=y
+CONFIG_UIO_XILINX_APM=y
+CONFIG_VIRTIO=y
+CONFIG_COMMON_CLK=y
+CONFIG_COMMON_CLK_SI570=y
+CONFIG_COMMON_CLK_ZYNQMP=y
+CONFIG_CLKSRC_OF=y
+CONFIG_IOMMU_API=y
+CONFIG_IOMMU_SUPPORT=y
+CONFIG_OF_IOMMU=y
+CONFIG_ARM_SMMU=y
+CONFIG_ARM_SMMU_V3=y
+#
+CONFIG_REMOTEPROC=m
remotproc doesn't belong in a BSP fragment.
remove it.
+CONFIG_ZYNQMP_R5_REMOTEPROC=m
+
+CONFIG_STAGING=y
+CONFIG_SOC_XILINX_ZYNQMP=y
+CONFIG_ZYNQMP_PM_DOMAINS=y
+CONFIG_PM_GENERIC_DOMAINS=y
+CONFIG_ZYNQMP_PM_API=y
+CONFIG_IRQCHIP=y
+CONFIG_ARM_GIC=y
+CONFIG_ARM_GIC_V3=y
+CONFIG_ARM_GIC_V3_ITS=y
+
+CONFIG_IIO=y
+CONFIG_XILINX_AMS=y
+CONFIG_XILINX_FCLK=y
+
+CONFIG_FPGA=y
+CONFIG_FPGA_MGR_ZYNQMP_FPGA=y
+CONFIG_NVMEM_ZYNQMP=y
+CONFIG_FPGA_REGION=y
+CONFIG_FPGA_BRIDGE=y
+
+CONFIG_RESET_CONTROLLER=y
+CONFIG_ZYNQMP_RESET_CONTROLLER=y
+
+CONFIG_REGULATOR=y
+CONFIG_REGULATOR_FIXED_VOLTAGE=y
+CONFIG_REGULATOR_GPIO=y
+
+
+CONFIG_FB=y
+CONFIG_FB_XILINX=y
+CONFIG_MEDIA_SUPPORT=y
+CONFIG_MEDIA_CONTROLLER=y
+CONFIG_MEDIA_CAMERA_SUPPORT=y
+CONFIG_VIDEO_DEV=y
+CONFIG_VIDEO_V4L2_SUBDEV_API=y
+CONFIG_VIDEO_V4L2=y
+CONFIG_V4L_PLATFORM_DRIVERS=y
+CONFIG_VIDEO_XILINX=y
+CONFIG_VIDEO_XILINX_CFA=y
+CONFIG_VIDEO_XILINX_CRESAMPLE=y
+CONFIG_VIDEO_XILINX_HLS=y
+CONFIG_VIDEO_XILINX_REMAPPER=y
+CONFIG_VIDEO_XILINX_RGB2YUV=y
+CONFIG_VIDEO_XILINX_SCALER=y
+CONFIG_VIDEO_XILINX_SWITCH=y
+CONFIG_VIDEO_XILINX_TPG=y
+CONFIG_VIDEO_XILINX_VTC=y
The CONFIG_FB and related fragments can be separated out into a
feature fragment and then included. That's what we've done with other
FB features.
En, yeah, these parts are BSP related other than this just one
CONFIG_FB, can we live with these as other BSPs did?
+
+CONFIG_DRM=y
+CONFIG_DRM_KMS_HELPER=y
+CONFIG_DRM_KMS_FB_HELPER=y
+CONFIG_DRM_FBDEV_EMULATION=y
+CONFIG_DRM_BRIDGE=y
+CONFIG_DRM_XILINX=y
+CONFIG_HDMI=y
+CONFIG_XILINX_FRMBUF=y
+CONFIG_XILINX_DPDMA=y
+CONFIG_XILINX_DMA_ENGINES=y
+
+CONFIG_FW_LOADER=y
+
+CONFIG_TIGON3=m
+CONFIG_E1000E=m
Overall, this looks good to me. It just needs a bit of tweaking for reuse.
OK, I'll send v2 with sanity test, thanks Bruce.
Cheers,
Zumeng
Bruce
diff --git a/bsp/xilinx-zynqmp/xilinx-zynqmp.scc
b/bsp/xilinx-zynqmp/xilinx-zynqmp.scc
new file mode 100644
index 0000000..81696c2
--- /dev/null
+++ b/bsp/xilinx-zynqmp/xilinx-zynqmp.scc
@@ -0,0 +1,7 @@
+include cfg/usb-mass-storage.scc
+include cfg/fs/flash_fs.cfg
+include features/hugetlb/hugetlb.scc
+# enable the ability to run 32 bit apps
+include arch/arm/32bit-compat.scc
+
+kconf hardware xilinx-zynqmp.cfg
--
2.7.4
--
- Thou shalt not follow the NULL pointer, for chaos and madness await
thee at its end
- "Use the force Harry" - Gandalf, Star Trek II
--
_______________________________________________
linux-yocto mailing list
linux-yocto@yoctoproject.org
https://lists.yoctoproject.org/listinfo/linux-yocto
