Hi again all,
I am able to boot and get X up. It takes about 45 seconds, which is not
bad, but it is a bit more than I was expecting. sshd takes up a bit of
this time though. I have most everything else disabled.
One of the largest problems is that none of the onboard USB ports work.
Also, none of the PCI cards I am using appears to work as well (Which
all of the devices work fine with the factory bios). Finally, I
unfortunately rely heavily on ACPI to startup and shutdown the system.
I have included a bit of output with this message, such as my config
file, output from `lspci -vvv`, and the output from `dmesg`. Perhaps I
did something wrong, or I'm setting my expectations a bit too high. I
appreciate anyone's time and effort that the may put into this, and I
thinking this pretty much rocks! (This would explain why I bought
another motherboard and a few extra DOCs...)
Any and all ideas are appreciated!
Regards,
Todd E. Johnson
[EMAIL PROTECTED]
Linux version 2.4.19 (root@grandamp) (gcc version 2.95.3 20010315 (release)) #23 Thu
Oct 3 19:19:23 EST 2002
BIOS-provided physical RAM map:
BIOS-e801: 0000000000000000 - 000000000009f000 (usable)
BIOS-e801: 0000000000100000 - 000000001f700000 (usable)
503MB LOWMEM available.
Advanced speculative caching feature not present
On node 0 totalpages: 128768
zone(0): 4096 pages.
zone(1): 124672 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/hda2 video=sisfb:800x600-16@72
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
Initializing CPU#0
Detected 1102.511 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 2202.00 BogoMIPS
Memory: 506428k/515072k available (1694k kernel code, 8256k reserved, 622k data, 112k
init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: Before vendor init, caps: 0383fbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After vendor init, caps: 0383fbff 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
CPU: Intel(R) Celeron(TM) CPU 1100MHz stepping 01
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1102.5109 MHz.
..... host bus clock speed is 100.2281 MHz.
cpu: 0, clocks: 1002281, slice: 501140
CPU0<T0:1002272,T1:501120,D:12,S:501140,C:1002281>
mtrr: v1.40 (20010327) Richard Gooch ([EMAIL PROTECTED])
mtrr: detected mtrr type: Intel
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unknown bridge resource 0: assuming transparent
Unknown bridge resource 2: assuming transparent
PCI: Using IRQ router SIS [1039/0008] at 00:01.0
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Installing knfsd (copyright (C) 1996 [EMAIL PROTECTED]).
ACPI: System description tables not found
ACPI-0068: *** Error: Acpi_load_tables: Could not get RSDP, AE_ERROR
ACPI-0116: *** Error: Acpi_load_tables: Could not load tables: AE_ERROR
ACPI: System description table load failed
parport0: PC-style at 0x378 (0x778) [PCSPP(,...)]
parport0: irq 7 detected
i2c-core.o: i2c core module
i2c-algo-bit.o: i2c bit algorithm module
sisfb_lite: $Id: linux-2.4.19-sis.patch,v 1.1 2002/09/03 02:56:32 ollie Exp $
sisfb_lite: framebuffer at 0xf0000000, mapped to 0xe0000000, size 8192 KB
sisfb_lite: Turned on MTRR Write Combine for framebuffer
sisfb_lite: Use 64KB off-screen memory for Turbo Queue
sisfb_lite: Video Dot Clock = 50113 KHz
Console: switching to colour frame buffer device 100x37
Detected PS/2 Mouse Port.
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
PCI: Assigned IRQ 5 for device 00:01.6
PCI: Sharing IRQ 5 with 00:01.4
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SIS5513: IDE controller on PCI bus 00 dev 01
SiS pirq: advanced IDE/ACPI/DAQ mapping not yet implemented
advanced SiS pirq mapping not yet implemented
SIS5513: chipset revision 208
SIS5513: not 100% native mode: will probe irqs later
SiS630
ide0: BM-DMA at 0x2c80-0x2c87, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0x2c88-0x2c8f, BIOS settings: hdc:pio, hdd:pio
hda: C/H/S=0/0/0 from BIOS ignored
hda: WDC WD1000BB-00CAA0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: 195371568 sectors (100030 MB) w/2048KiB Cache, CHS=193821/16/63, UDMA(66)
Partition check:
hda: [PTBL] [12161/255/63] hda1 hda2 hda3
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
sis900.c: v1.08.04 4/25/2002
PCI: Assigned IRQ 9 for device 00:01.1
eth0: SiS 900 Internal MII PHY transceiver found at address 1.
eth0: Using transceiver found at address 1 as default
eth0: SiS 900 PCI Fast Ethernet at 0x2000, IRQ 9, 00:07:95:ec:1e:ae.
Linux video capture interface: v1.00
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 431M
agpgart: unsupported bridge
agpgart: no supported devices found.
SCSI subsystem driver Revision: 1.00
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
ohci1394: $Rev: 530 $ Ben Collins <[EMAIL PROTECTED]>
PCI: No IRQ known for interrupt pin A of device 02:0b.0. Please try using pci=biosirq.
ohci1394: Failed to allocate shared interrupt 0
video1394: Installed video1394 module
raw1394: /dev/raw1394 device initialized
ieee1394: sbp2: Please load the lower level IEEE-1394 driver (e.g. ohci1394) before
sbp2...
cmpci: version $Revision: 5.64 $ time 15:00:42 Oct 3 2002
PCI: Enabling device 00:0f.0 (0080 -> 0081)
PCI: No IRQ known for interrupt pin A of device 00:0f.0. Please try using pci=biosirq.
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
PCI: No IRQ known for interrupt pin C of device 02:08.2. Please try using pci=biosirq.
hcd.c: Found HC with no IRQ. Check BIOS/PCI 02:08.2 setup!
PCI: Assigned IRQ 11 for device 00:01.2
PCI: Sharing IRQ 11 with 00:01.3
usb-ohci.c: USB OHCI at membase 0xe0822000, IRQ 11
usb-ohci.c: usb-00:01.2, Silicon Integrated Systems [SiS] 7001
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 3 ports detected
PCI: Found IRQ 11 for device 00:01.3
PCI: Sharing IRQ 11 with 00:01.2
usb-ohci.c: USB OHCI at membase 0xe0824000, IRQ 11
usb-ohci.c: usb-00:01.3, Silicon Integrated Systems [SiS] 7001 (#2)
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
PCI: No IRQ known for interrupt pin A of device 02:08.0. Please try using pci=biosirq.
usb-ohci.c: found OHCI device with no IRQ assigned. check BIOS settings!
PCI: No IRQ known for interrupt pin B of device 02:08.1. Please try using pci=biosirq.
usb-ohci.c: found OHCI device with no IRQ assigned. check BIOS settings!
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <[EMAIL PROTECTED]>
hid-core.c: USB HID support drivers
usb.c: registered new driver powermate
usb.c: registered new driver usbtouch
usbtouch.c: USB Touchscreen support registered.
usb.c: registered new driver serial
usbserial.c: USB Serial support registered for Generic
usbserial.c: USB Serial Driver core v1.4
usbserial.c: USB Serial support registered for Belkin F5U120-PC USB Serial Adapter
usbserial.c: USB Serial support registered for Belkin F5U103 USB Serial Adapter
usbserial.c: USB Serial support registered for Belkin USB Serial Adapter
usbserial.c: USB Serial support registered for Peracom single port USB Serial Adapter
usbserial.c: USB Serial support registered for GO-COM232 USB Serial Converter
belkin_sa.c: USB Belkin Serial converter driver v1.1
usbserial.c: USB Serial support registered for Magic Control Technology USB-RS232
usbserial.c: USB Serial support registered for MCT/Sitecom USB-RS232
usbserial.c: USB Serial support registered for MCT/D-Link DU-H3SP USB BAY
mct_u232.c: v1.1:Magic Control Technology USB-RS232 converter driver
usbserial.c: USB Serial support registered for PL-2303
pl2303.c: Prolific PL2303 USB to serial adaptor driver v0.9
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
IrCOMM protocol (Dag Brattli)
FAT: bogus logical sector size 0
FAT: bogus logical sector size 0
reiserfs: checking transaction log (device 03:02) ...
Warning, log replay starting on readonly filesystem
hub.c: USB new device connect on bus2/2, assigned device number 2
usb.c: USB device not accepting new address=2 (error=-110)
hub.c: USB new device connect on bus2/2, assigned device number 3
usb.c: USB device not accepting new address=3 (error=-110)
reiserfs: replayed 8 transactions in 1 seconds
Using r5 hash to sort names
ReiserFS version 3.6.25
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 112k freed
Adding Swap: 248968k swap-space (priority -1)
reiserfs: checking transaction log (device 03:03) ...
reiserfs: replayed 10 transactions in 1 seconds
Using r5 hash to sort names
ReiserFS version 3.6.25
eth0: Media Link On 10mbps half-duplex
usbtouch.c: open_usbtouch(0): invalid tscrn_minor
sisfb_lite: Video Dot Clock = 50113 KHz
hub.c: USB new device connect on bus1/2, assigned device number 2
usb.c: USB device not accepting new address=2 (error=-110)
hub.c: USB new device connect on bus1/2, assigned device number 3
usb.c: USB device not accepting new address=3 (error=-110)
hub.c: USB new device connect on bus1/1, assigned device number 4
usb.c: USB device not accepting new address=4 (error=-110)
hub.c: USB new device connect on bus1/1, assigned device number 5
usb.c: USB device not accepting new address=5 (error=-110)
hub.c: USB new device connect on bus2/2, assigned device number 4
usb.c: USB device not accepting new address=4 (error=-110)
hub.c: USB new device connect on bus2/2, assigned device number 5
usb.c: USB device not accepting new address=5 (error=-110)
hub.c: USB new device connect on bus2/1, assigned device number 6
usb.c: USB device not accepting new address=6 (error=-110)
hub.c: USB new device connect on bus2/1, assigned device number 7
usb.c: USB device not accepting new address=7 (error=-110)
hub.c: USB new device connect on bus2/1, assigned device number 8
usb.c: USB device not accepting new address=8 (error=-110)
hub.c: USB new device connect on bus2/1, assigned device number 9
usb.c: USB device not accepting new address=9 (error=-110)
00:00.0 Host bridge: Silicon Integrated Systems [SiS] 630 Host (rev 30)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Latency: 64
Region 0: Memory at f8000000 (32-bit, non-prefetchable) [size=64M]
Capabilities: [c0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2,x4
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=x4
00:00.1 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev d0) (prog-if
80 [Master])
Subsystem: Silicon Integrated Systems [SiS] SiS5513 EIDE Controller (A,B step)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 16
Interrupt: pin A routed to IRQ 14
Region 4: I/O ports at 2c80 [size=16]
00:01.0 ISA bridge: Silicon Integrated Systems [SiS] 85C503/5513
Control: I/O- Mem- BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
00:01.1 Ethernet controller: Silicon Integrated Systems [SiS] SiS900 10/100 Ethernet
(rev 84)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (13000ns min, 2750ns max)
Interrupt: pin C routed to IRQ 9
Region 0: I/O ports at 2000 [size=256]
Region 1: Memory at fc200000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=160mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.2 USB Controller: Silicon Integrated Systems [SiS] 7001 (rev 07) (prog-if 10
[OHCI])
Subsystem: Silicon Integrated Systems [SiS] 7001
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (20000ns max)
Interrupt: pin D routed to IRQ 11
Region 0: Memory at fc201000 (32-bit, non-prefetchable) [size=4K]
00:01.3 USB Controller: Silicon Integrated Systems [SiS] 7001 (rev 07) (prog-if 10
[OHCI])
Subsystem: Silicon Integrated Systems [SiS]: Unknown device 7000
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (20000ns max)
Interrupt: pin D routed to IRQ 11
Region 0: Memory at fc202000 (32-bit, non-prefetchable) [size=4K]
00:01.4 Multimedia audio controller: Silicon Integrated Systems [SiS] SiS PCI Audio
Accelerator (rev 02)
Subsystem: Silicon Integrated Systems [SiS] SiS PCI Audio Accelerator
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 5
Region 0: I/O ports at 2400 [size=256]
Region 1: Memory at fc203000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=55mA
PME(D0-,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.6 Modem: Silicon Integrated Systems [SiS] 56k Winmodem (Smart Link HAMR5600
compatible) (rev a0) (prog-if 00 [Gene
ric])
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 5
Region 0: I/O ports at 2800 [size=256]
Region 1: I/O ports at 2c00 [size=128]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:02.0 PCI bridge: Silicon Integrated Systems [SiS] 5591/5592 AGP (prog-if 00 [Normal
decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00001000-00001fff
Memory behind bridge: fc000000-fc0fffff
Prefetchable memory behind bridge: f0000000-f7ffffff
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
00:0b.0 PCI bridge: Hint Corp HB1-SE33 PCI-PCI Bridge (rev 13) (prog-if 00 [Normal
decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64, cache line size 10
Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
I/O behind bridge: 00002000-00001fff
Memory behind bridge: fc100000-fc1fffff
Prefetchable memory behind bridge: 00000000fc200000-00000000fc100000
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [90] #06 [0000]
Capabilities: [a0] Vital Product Data
00:0d.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 0
Region 0: Memory at fc204000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0d.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 0
Region 0: Memory at fc205000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0f.0 Multimedia audio controller: C-Media Electronics Inc CM8738 (rev 10)
Subsystem: C-Media Electronics Inc CMI8738/C3DX PCI Audio Device
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 0
Region 0: I/O ports at ff00 [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: Silicon Integrated Systems [SiS] SiS630 GUI
Accelerator+3D (rev 21) (prog-if 00 [VGA]
)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
BIST result: 00
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
Region 1: Memory at fc000000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at 1000 [size=128]
Capabilities: [40] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] AGP version 2.0
Status: RQ=15 SBA+ 64bit- FW- Rate=x1,x2,x4
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
02:08.0 USB Controller: NEC Corporation USB (rev 41) (prog-if 10 [OHCI])
Subsystem: Adaptec: Unknown device 0235
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 0
Region 0: Memory at fc104000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:08.1 USB Controller: NEC Corporation USB (rev 41) (prog-if 10 [OHCI])
Subsystem: Adaptec: Unknown device 0235
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 0
Region 0: Memory at fc105000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:08.2 USB Controller: NEC Corporation USB 2.0 (rev 02) (prog-if 20 [EHCI])
Subsystem: Adaptec: Unknown device 02e0
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 0
Region 0: Memory at fc107000 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:0b.0 FireWire (IEEE 1394): Texas Instruments TSB12LV26 IEEE-1394 Controller (Link)
(prog-if 10 [OHCI])
Subsystem: Texas Instruments: Unknown device 8010
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (750ns min, 1000ns max), cache line size 10
Interrupt: pin A routed to IRQ 0
Region 0: Memory at fc106000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at fc100000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
m758lmr+.config
Description: Binary data
