Well, I have looked on the source, and it seems that the eaglelion/5bcm
use the same hardware. Now I will have a try with that settings and see
what happens :D
First test with same settings as for eaglelion/5bcm
It seems that LB boots nearly correct, but after the bootloader calls
filo the Board stops any output.
Filo produce no output, too.
I'm not sure, but filo tries to bring up the vga console and fails.
Or is there any other reason why filo could fail?
What does filo first?
Also the serial output says, that LB fails to copy the IRQ Table. I
think that is not good :D and could be the main reason. Because of the
IRQs for IDE.
Any Hints?
Here are the results ;) (attachment)
thanks chris
LinuxBIOS-1.1.8.0Fallback Thu Apr 20 15:51:26 CEST 2006 starting...
Setting up default parameters for memory
Sizing memory
Probing for DIMM0
Found DIMM0
Page Size: 00001000
Component Banks: 4
Module Banks: 1
DIMM size: 04000000
Probing for DIMM1
MC_BANK_CFG = 00701420
Copying LinuxBIOS to ram.
Jumping to LinuxBIOS.
LinuxBIOS-1.1.8.0Fallback Thu Apr 20 15:51:26 CEST 2006 booting...
clocks_per_usec: 375
Enumerating buses...
Finding PCI configuration type.
PCI: Using configuration type 1
PCI_DOMAIN: 0000 enabled
PCI: pci_scan_bus for bus 0
PCI: 00:00.0 [1078/0001] enabled
PCI: 00:09.0 [10ea/5000] enabled
PCI: 00:12.0 [1078/0100] enabled
PCI: 00:12.1 [1078/0101] enabled
PCI: 00:12.2 [1078/0102] enabled
PCI: 00:12.3 [1078/0103] enabled
PCI: 00:12.4 [1078/0104] enabled
PCI: 00:13.0 [0e11/a0f8] enabled
PNP: 002e.0 enabled
PNP: 002e.1 enabled
PNP: 002e.2 enabled
PNP: 002e.3 disabled
PNP: 002e.4 enabled
PNP: 002e.5 enabled
PNP: 002e.6 enabled
PNP: 002e.7 enabled
PNP: 002e.8 enabled
PCI: 00:12.1 disabled
PCI: 00:12.2 enabled
PCI: 00:12.3 disabled
PCI: 00:12.4 disabled
PCI: pci_scan_bus returning with max=00
done
Allocating resources...
Reading resources...
Done reading resources.
Setting resources...
BC_DRAM_TOP = 0x03bfffff
MC_GBASE_ADD = 0x00000078
I would set ram size to 60 Mbytes
PCI: 00:09.0 10 <- [0x00fd000000 - 0x00fdffffff] mem
PCI: 00:09.0 30 <- [0x00fe000000 - 0x00fe00ffff] romem
PCI: 00:12.1 10 <- [0x00fe012000 - 0x00fe0120ff] mem
PCI: 00:12.2 20 <- [0x0000001000 - 0x000000107f] io
PCI: 00:12.3 10 <- [0x00fe013000 - 0x00fe01307f] mem
PCI: 00:12.4 10 <- [0x00fe010000 - 0x00fe010fff] mem
PCI: 00:13.0 10 <- [0x00fe011000 - 0x00fe011fff] mem
Done setting resources.
Done allocating resources.
Enabling resourcess...
PCI: 00:00.0 cmd <- 147
PCI: 00:09.0 cmd <- 142
PCI: 00:12.0 cmd <- 14f
PCI: 00:12.2 missing enable_resources
PCI: 00:12.1 cmd <- 142
PCI: 00:12.2 cmd <- 141
PCI: 00:12.3 cmd <- 142
PCI: 00:12.4 cmd <- 142
PCI: 00:13.0 cmd <- 142
done.
Initializing devices...
Root Device init
PCI: 00:00.0 init
northbridge: northbridge_init()
PCI: 00:12.0 init
PNP: 002e.0 init
PNP: 002e.1 init
PNP: 002e.2 init
PNP: 002e.4 init
PNP: 002e.5 init
PNP: 002e.6 init
PNP: 002e.7 init
PNP: 002e.8 init
PCI: 00:09.0 init
PCI: 00:12.1 init
PCI: 00:12.2 init
PCI: 00:12.3 init
PCI: 00:12.4 init
PCI: 00:13.0 init
Devices initialized
Copying IRQ routing tables to 0xf0000...done.
Verifing copy of IRQ routing tables at 0xf0000...failed
Moving GDT to 0x500...ok
Wrote linuxbios table at: 00000530 - 000006c4 checksum a262
Welcome to elfboot, the open sourced starter.
January 2002, Eric Biederman.
Version 1.3
33:stream_init() - rom_stream: 0xfffe0000 - 0xfffeffff
Found ELF candiate at offset 0
New segment addr 0x100000 size 0x23d00 offset 0xa0 filesize 0x9c68
(cleaned up) New segment addr 0x100000 size 0x23d00 offset 0xa0 filesize 0x9c68
New segment addr 0x123d00 size 0x48 offset 0x9d20 filesize 0x48
(cleaned up) New segment addr 0x123d00 size 0x48 offset 0x9d20 filesize 0x48
Dropping non PT_LOAD segment
Loading Segment: addr: 0x0000000000100000 memsz: 0x0000000000023d00 filesz:
0x0000000000009c68
Clearing Segment: addr: 0x0000000000109c68 memsz: 0x000000000001a098
Loading Segment: addr: 0x0000000000123d00 memsz: 0x0000000000000048 filesz:
0x0000000000000048
Jumping to boot code at 0x1078c4
--
linuxbios mailing list
[email protected]
http://www.openbios.org/mailman/listinfo/linuxbios
