Hi Yinghai,
On Mon, Sep 17, 2007 at 08:40:41PM +0200, [EMAIL PROTECTED] wrote:
> > 1. 64 bit kernel? I never tried 32 bit kernel...
> I have done tests with both types (32b & 64b)=> same results!
>
> > 2. nothing to with irq.
> Ok
>
> > 3. boot log wht pci_vga card?
> The boot log that i have send (which encompasses both LinuxBIOS and Linux
> kernel
> boot logs, captured on a serial link) "lb_linux_dump.txt", was done with the
> pci
> vga card plugged into a "normal" (not PCIe) slot.
I've attached that boot log to this message.
Thanks,
Ward.
--
Ward Vandewege <[EMAIL PROTECTED]>
Free Software Foundation - Senior System Administrator
LinuxBIOS-2.0.0_m57sli_Fallback lundi 10 septembre 2007, 19:14:19 (UTC+0200)
starting...
*sysinfo range: [000cf000,000cf730)
bsp_apicid=00
core0 started:
started ap apicid: 01
SBLink=00
NC node|link=00
begin msr fid, vid 31081212080c0202
end msr fid, vid 31081208080c020c
mcp55_num:01
ht reset -
LinuxBIOS-2.0.0_m57sli_Fallback lundi 10 septembre 2007, 19:14:19 (UTC+0200)
starting...
*sysinfo range: [000cf000,000cf730)
bsp_apicid=00
core0 started:
started ap apicid: 01
SBLink=00
NC node|link=00
begin msr fid, vid 31081208080c020c
end msr fid, vid 31081208080c020c
mcp55_num:01
Ram1.00
Ram2.00
Unbuffered
400Mhz
Interleaved
RAM: 0x00200000 KB
Ram3
dimm_mask = 00000011
x4_mask = 00000000
x16_mask = 00000000
single_rank_mask = 00000000
ODC = 00113222
Addr Timing= 00202520
Initializing memory: done
Setting variable MTRR 2, base: 0MB, range: 2048MB, type WB
set DQS timing:RcvrEn:Pass1: 00 CTLRMaxDelay=17 done
set DQS timing:DQSPos: 00 done
set DQS timing:RcvrEn:Pass2: 00 CTLRMaxDelay=2c done
Total DQS Training : tsc [00]=00000000324d23be
Total DQS Training : tsc [01]=00000000339dcdf3
Total DQS Training : tsc [02]=0000000087337f2b
Total DQS Training : tsc [03]=00000000885122c3
Ram4
v_esp=000cee78
testx = 5a5a5a5a
Copying data from cache to RAM -- switching to use RAM as stack... Done
testx = 5a5a5a5a
Disabling cache as ram now
Clearing initial memory region: Done
Copying LinuxBIOS to RAM.
src=fffdf000
dst=00100000
linxbios_ram.nrv2b length = 0000d667
linxbios_ram.bin length = 000225d0
Jumping to LinuxBIOS.
LinuxBIOS-2.0.0_m57sli_Fallback mardi 11 septembre 2007, 12:45:25 (UTC+0200)
booting...
Enumerating buses...
APIC_CLUSTER: 0 enabled
PCI_DOMAIN: 0000 enabled
PCI: 00:18.3 siblings=1
CPU: APIC: 00 enabled
CPU: APIC: 01 enabled
PCI: pci_scan_bus for bus 00
PCI: 00:18.0 [1022/1100] enabled
PCI: 00:18.1 [1022/1101] enabled
PCI: 00:18.2 [1022/1102] enabled
PCI: 00:18.3 [1022/1103] enabled
PCI: 00:00.0 [10de/0369] enabled
PCI: 00:00.0 [10de/0369] enabled next_unitid: 0010
PCI: pci_scan_bus for bus 00
PCI: 00:00.0 [10de/0369] enabled
PCI: 00:01.0 [10de/0360] enabled
PCI: 00:01.1 [10de/0368] enabled
PCI: 00:01.2 [10de/036a] enabled
PCI: 00:01.3 [10de/036b] enabled
PCI: 00:02.0 [10de/036c] enabled
PCI: 00:02.1 [10de/036d] enabled
PCI: 00:04.0 [10de/036e] enabled
PCI: 00:05.0 [10de/037f] enabled
PCI: 00:05.1 [10de/037f] enabled
PCI: 00:05.2 [10de/037f] enabled
PCI: 00:06.0 [10de/0370] enabled
PCI: 00:06.1 [10de/0371] enabled
PCI: 00:08.0 [10de/0373] enabled
PCI: 00:0a.0 [10de/0376] enabled
PCI: 00:0b.0 [10de/0374] enabled
PCI: 00:0c.0 [10de/0374] enabled
PCI: 00:0d.0 [10de/0378] enabled
PCI: 00:0e.0 [10de/0375] enabled
PCI: 00:0f.0 [10de/0377] enabled
PNP: 002e.0 disabled
PNP: 002e.1 enabled
PNP: 002e.2 disabled
PNP: 002e.3 disabled
PNP: 002e.4 enabled
PNP: 002e.5 enabled
PNP: 002e.6 enabled
PNP: 002e.8 disabled
PNP: 002e.9 disabled
PNP: 002e.a disabled
smbus: PCI: 00:01.1[0]->I2C: 01:50 enabled
smbus: PCI: 00:01.1[0]->I2C: 01:51 enabled
smbus: PCI: 00:01.1[0]->I2C: 01:52 enabled
smbus: PCI: 00:01.1[0]->I2C: 01:53 enabled
smbus: PCI: 00:01.1[0]->I2C: 01:54 enabled
smbus: PCI: 00:01.1[0]->I2C: 01:55 enabled
smbus: PCI: 00:01.1[0]->I2C: 01:56 enabled
smbus: PCI: 00:01.1[0]->I2C: 01:57 enabled
smbus: PCI: 00:01.1[1]->I2C: 02:51 enabled
PCI: pci_scan_bus for bus 01
PCI: pci_scan_bus returning with max=001
PCI: pci_scan_bus for bus 02
PCI: pci_scan_bus returning with max=002
PCI: pci_scan_bus for bus 03
PCI: pci_scan_bus returning with max=003
PCI: pci_scan_bus for bus 04
PCI: pci_scan_bus returning with max=004
PCI: pci_scan_bus for bus 05
PCI: pci_scan_bus returning with max=005
PCI: pci_scan_bus for bus 06
PCI: pci_scan_bus returning with max=006
PCI: pci_scan_bus for bus 07
PCI: pci_scan_bus returning with max=007
PCI: pci_scan_bus returning with max=007
PCI: pci_scan_bus returning with max=007
done
Allocating resources...
Reading resources...
PCI: 00:06.0 1c <- [0x000000f000 - 0x000000efff] bus 01 io
PCI: 00:06.0 24 <- [0x00fff00000 - 0x00ffefffff] bus 01 prefmem
PCI: 00:06.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 01 mem
PCI: 00:0a.0 1c <- [0x00fffff000 - 0x00ffffefff] bus 02 io
PCI: 00:0a.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 02 prefmem
PCI: 00:0a.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 02 mem
PCI: 00:0b.0 1c <- [0x00fffff000 - 0x00ffffefff] bus 03 io
PCI: 00:0b.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 03 prefmem
PCI: 00:0b.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 03 mem
PCI: 00:0c.0 1c <- [0x00fffff000 - 0x00ffffefff] bus 04 io
PCI: 00:0c.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 04 prefmem
PCI: 00:0c.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 04 mem
PCI: 00:0d.0 1c <- [0x00fffff000 - 0x00ffffefff] bus 05 io
PCI: 00:0d.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 05 prefmem
PCI: 00:0d.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 05 mem
PCI: 00:0e.0 1c <- [0x00fffff000 - 0x00ffffefff] bus 06 io
PCI: 00:0e.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 06 prefmem
PCI: 00:0e.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 06 mem
PCI: 00:0f.0 1c <- [0x00fffff000 - 0x00ffffefff] bus 07 io
PCI: 00:0f.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 07 prefmem
PCI: 00:0f.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 07 mem
Done reading resources.
Setting resources...
PCI: 00:18.0 1c0 <- [0x0000001000 - 0x0000002fff] io <node 0 link 0>
PCI: 00:18.0 1b8 <- [0x00fc100000 - 0x00fc0fffff] prefmem <node 0 link 0>
PCI: 00:18.0 1b0 <- [0x00fc000000 - 0x00fc0fffff] mem <node 0 link 0>
PCI: 00:01.0 14 <- [0x00fc044000 - 0x00fc044fff] mem
PNP: 002e.1 60 <- [0x00000003f8 - 0x00000003ff] io
PNP: 002e.1 70 <- [0x0000000004 - 0x0000000004] irq
PNP: 002e.4 60 <- [0x0000000290 - 0x0000000297] io
PNP: 002e.4 62 <- [0x0000000230 - 0x0000000237] io
PNP: 002e.4 70 <- [0x0000000009 - 0x0000000009] irq
PNP: 002e.5 60 <- [0x0000000060 - 0x0000000060] io
PNP: 002e.5 62 <- [0x0000000064 - 0x0000000064] io
PNP: 002e.5 70 <- [0x0000000001 - 0x0000000001] irq
PNP: 002e.6 70 <- [0x000000000c - 0x000000000c] irq
PCI: 00:01.1 10 <- [0x0000001c00 - 0x0000001c3f] io
PCI: 00:01.1 20 <- [0x0000001c40 - 0x0000001c7f] io
PCI: 00:01.1 24 <- [0x0000001c80 - 0x0000001cbf] io
PCI: 00:01.1 60 <- [0x0000001000 - 0x00000010ff] io
PCI: 00:01.1 64 <- [0x0000001400 - 0x00000014ff] io
PCI: 00:01.1 68 <- [0x0000001800 - 0x00000018ff] io
PCI: 00:01.3 10 <- [0x00fc000000 - 0x00fc03ffff] mem
PCI: 00:02.0 10 <- [0x00fc045000 - 0x00fc045fff] mem
PCI: 00:02.1 10 <- [0x00fc04a000 - 0x00fc04a0ff] mem
PCI: 00:04.0 20 <- [0x0000001cc0 - 0x0000001ccf] io
PCI: 00:05.0 10 <- [0x0000002000 - 0x0000002007] io
PCI: 00:05.0 14 <- [0x0000002070 - 0x0000002073] io
PCI: 00:05.0 18 <- [0x0000002010 - 0x0000002017] io
PCI: 00:05.0 1c <- [0x0000002080 - 0x0000002083] io
PCI: 00:05.0 20 <- [0x0000001cd0 - 0x0000001cdf] io
PCI: 00:05.0 24 <- [0x00fc046000 - 0x00fc046fff] mem
PCI: 00:05.1 10 <- [0x0000002020 - 0x0000002027] io
PCI: 00:05.1 14 <- [0x0000002090 - 0x0000002093] io
PCI: 00:05.1 18 <- [0x0000002030 - 0x0000002037] io
PCI: 00:05.1 1c <- [0x00000020a0 - 0x00000020a3] io
PCI: 00:05.1 20 <- [0x0000001ce0 - 0x0000001cef] io
PCI: 00:05.1 24 <- [0x00fc047000 - 0x00fc047fff] mem
PCI: 00:05.2 10 <- [0x0000002040 - 0x0000002047] io
PCI: 00:05.2 14 <- [0x00000020b0 - 0x00000020b3] io
PCI: 00:05.2 18 <- [0x0000002050 - 0x0000002057] io
PCI: 00:05.2 1c <- [0x00000020c0 - 0x00000020c3] io
PCI: 00:05.2 20 <- [0x0000001cf0 - 0x0000001cff] io
PCI: 00:05.2 24 <- [0x00fc048000 - 0x00fc048fff] mem
PCI: 00:06.1 10 <- [0x00fc040000 - 0x00fc043fff] mem
PCI: 00:08.0 10 <- [0x00fc049000 - 0x00fc049fff] mem
PCI: 00:08.0 14 <- [0x0000002060 - 0x0000002067] io
PCI: 00:08.0 18 <- [0x00fc04b000 - 0x00fc04b0ff] mem
PCI: 00:08.0 1c <- [0x00fc04c000 - 0x00fc04c00f] mem
PCI: 00:18.3 94 <- [0x00f8000000 - 0x00fbffffff] mem <gart>
Done setting resources.
Done allocating resources.
Enabling resources...
PCI: 00:18.0 cmd <- 140
PCI: 00:00.0 subsystem <- 1022/2b80
PCI: 00:00.0 cmd <- 146
PCI: 00:01.0 subsystem <- 1022/2b80
PCI: 00:01.0 cmd <- 14f
mcp55 lpc decode:PNP: 002e.1, base=0x000003f8, end=0x000003ff
mcp55 lpc decode:PNP: 002e.4, base=0x00000290, end=0x00000297
mcp55 lpc decode:PNP: 002e.4, base=0x00000230, end=0x00000237
mcp55 lpc decode:PNP: 002e.5, base=0x00000060, end=0x00000060
mcp55 lpc decode:PNP: 002e.5, base=0x00000064, end=0x00000064
PCI: 00:01.1 subsystem <- 1022/2b80
PCI: 00:01.1 cmd <- 141
PCI: 00:01.2 cmd <- 540
PCI: 00:01.3 cmd <- 142
PCI: 00:02.0 subsystem <- 1022/2b80
PCI: 00:02.0 cmd <- 142
PCI: 00:02.1 subsystem <- 1022/2b80
PCI: 00:02.1 cmd <- 142
PCI: 00:04.0 subsystem <- 1022/2b80
PCI: 00:04.0 cmd <- 141
PCI: 00:05.0 subsystem <- 1022/2b80
PCI: 00:05.0 cmd <- 143
PCI: 00:05.1 subsystem <- 1022/2b80
PCI: 00:05.1 cmd <- 143
PCI: 00:05.2 subsystem <- 1022/2b80
PCI: 00:05.2 cmd <- 143
PCI: 00:06.0 bridge ctrl <- 0a03
PCI: 00:06.0 cmd <- 144
PCI: 00:06.1 subsystem <- 1022/2b80
PCI: 00:06.1 cmd <- 142
PCI: 00:08.0 subsystem <- 1022/2b80
PCI: 00:08.0 cmd <- 143
PCI: 00:0a.0 bridge ctrl <- 0003
PCI: 00:0a.0 cmd <- 140
PCI: 00:0b.0 bridge ctrl <- 0003
PCI: 00:0b.0 cmd <- 140
PCI: 00:0c.0 bridge ctrl <- 0003
PCI: 00:0c.0 cmd <- 140
PCI: 00:0d.0 bridge ctrl <- 0003
PCI: 00:0d.0 cmd <- 140
PCI: 00:0e.0 bridge ctrl <- 0003
PCI: 00:0e.0 cmd <- 140
PCI: 00:0f.0 bridge ctrl <- 0003
PCI: 00:0f.0 cmd <- 140
PCI: 00:18.1 subsystem <- 1022/2b80
PCI: 00:18.1 cmd <- 140
PCI: 00:18.2 subsystem <- 1022/2b80
PCI: 00:18.2 cmd <- 140
PCI: 00:18.3 cmd <- 140
done.
Initializing devices...
Root Device init
APIC_CLUSTER: 0 init
start_eip=0x00006000, offset=0x00110000, code_size=0x0000005b
Initializing CPU #0
CPU: vendor AMD device 40fb2
CPU: family 0f, model 4b, stepping 02
Enabling cache
Setting fixed MTRRs(0-88) type: UC
Setting fixed MTRRs(0-16) Type: WB, RdMEM, WrMEM
Setting fixed MTRRs(24-88) Type: WB, RdMEM, WrMEM
DONE fixed MTRRs
Setting variable MTRR 0, base: 0MB, range: 2048MB, type WB
DONE variable MTRRs
Clear out the extra MTRR's
MTRR check
Fixed MTRRs : Enabled
Variable MTRRs: Enabled
CPU model AMD Athlon(tm) 64 X2 Dual Core Processor 3800+
Setting up local apic... apic_id: 0x00 done.
ECC Disabled
CPU #0 Initialized
Initializing CPU #1
Waiting for 1 CPUS to stop
CPU: vendor AMD device 40fb2
CPU: family 0f, model 4b, stepping 02
Enabling cache
Setting fixed MTRRs(0-88) type: UC
Setting fixed MTRRs(0-16) Type: WB, RdMEM, WrMEM
Setting fixed MTRRs(24-88) Type: WB, RdMEM, WrMEM
DONE fixed MTRRs
Setting variable MTRR 0, base: 0MB, range: 2048MB, type WB
DONE variable MTRRs
Clear out the extra MTRR's
MTRR check
Fixed MTRRs : Enabled
Variable MTRRs: Enabled
CPU model AMD Athlon(tm) 64 X2 Dual Core Processor 3800+
Setting up local apic... apic_id: 0x01 done.
CPU #1 Initialized
All AP CPUs stopped
PCI: 00:18.0 init
PCI: 00:01.0 init
set power on after power fail
RTC Init
Invalid CMOS LB checksum
PNP: 002e.1 init
PNP: 002e.4 init
FAN_CTL: reg = 0x02a9, read value = 0x50
FAN_CTL: reg = 0x02a9, writing value = 0xd7
PNP: 002e.5 init
Keyboard selftest failed
PNP: 002e.6 init
PCI: 00:01.1 init
PCI: 00:02.1 init
PCI: 00:04.0 init
IDE0
PCI: 00:05.0 init
SATA S SATA P
PCI: 00:05.1 init
SATA S SATA P
PCI: 00:05.2 init
SATA S SATA P
PCI: 00:06.0 init
dev_root mem base = 0x00f8000000
[0x50] <-- 0xf8000000
PCI: 00:06.1 init
base = fc040000
codec_mask = 01
codec viddid: 10ec0888
No verb!
PCI: 00:08.0 init
MCP55 MAC PHY ID 0x01410c00 PHY ADDR 1
PCI: 00:0a.0 init
PCI: 00:0b.0 init
PCI: 00:0c.0 init
PCI: 00:0d.0 init
PCI: 00:0e.0 init
PCI: 00:0f.0 init
PCI: 00:18.1 init
PCI: 00:18.2 init
PCI: 00:18.3 init
NB: Function 3 Misc Control.. done.
PCI: 00:01.2 init
PCI: 00:01.3 init
Devices initialized
Writing IRQ routing tables to 0xf0000...done.
Wrote the mp table end at: 00000020 - 00000274
Moving GDT to 0x500...ok
Adjust low_table_end from 0x00000530 to 0x00001000
Adjust rom_table_end from 0x000f0400 to 0x00100000
Wrote linuxbios table at: 00000530 - 00000de8 checksum 8b7b
Welcome to elfboot, the open sourced starter.
January 2002, Eric Biederman.
Version 1.3
rom_stream: 0xfffc0000 - 0xfffdefff
Found ELF candidate at offset 0
header_offset is 0
Try to load at offset 0x0
New segment addr 0x100000 size 0x3cd20 offset 0xc0 filesize 0x12d08
(cleaned up) New segment addr 0x100000 size 0x3cd20 offset 0xc0 filesize 0x12d08
New segment addr 0x13cd20 size 0x48 offset 0x12de0 filesize 0x48
(cleaned up) New segment addr 0x13cd20 size 0x48 offset 0x12de0 filesize 0x48
Dropping non PT_LOAD segment
Dropping non PT_LOAD segment
Loading Segment: addr: 0x000000007ff80000 memsz: 0x000000000003cd20 filesz:
0x0000000000012d08
Clearing Segment: addr: 0x000000007ff92d08 memsz: 0x000000000002a018
Loading Segment: addr: 0x000000007ffbcd20 memsz: 0x0000000000000048 filesz:
0x0000000000000048
Jumping to boot code at 0x10e4fc
FILO version 0.5 ([EMAIL PROTECTED]) Mon Jul 30 12:17:14 CEST 2007
menu: hda3:/boot/filo/menu.lst
hda: LBA 40GB: ST340016A
Mounted ext2fs
Mounted ext2fs
Found Linux version 2.6.20-15-generic ([EMAIL PROTECTED]) #2 SMP Sun Apr 15
06:17:24 UTC 2007 bzImage.
Loading kernel... ok
Loading initrd... ok
Jumping to entry point...
[ 0.000000] Linux version 2.6.20-15-generic ([EMAIL PROTECTED]) (gcc version
4.1.2 (Ubuntu 4.1.2-0ubuntu4)) #2 SMP Sun Apr 15 06:17:24 UTC 2007 (Ubuntu
2.6.20-15.27-generic)
[ 0.000000] Command line: acpi=off pci=noacpi,nobios console=tty0
console=ttyS0,115200 root=UUID=3bd44ac7-3a5b-4d3a-b452-fbbc051c9f8d ro
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000001000 - 00000000000a0000 (usable)
[ 0.000000] BIOS-e820: 00000000000c0000 - 00000000000f0000 (usable)
[ 0.000000] BIOS-e820: 0000000000100000 - 0000000080000000 (usable)
[ 0.000000] PCI: Unknown option `nobios'
[ 0.000000] end_pfn_map = 524288
[ 0.000000] DMI not present or invalid.
[ 0.000000] Scanning NUMA topology in Northbridge 24
[ 0.000000] Number of nodes 1
[ 0.000000] Node 0 MemBase 0000000000000000 Limit 0000000080000000
[ 0.000000] Using node hash shift of 63
[ 0.000000] Bootmem setup node 0 0000000000000000-0000000080000000
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 1 -> 4096
[ 0.000000] DMA32 4096 -> 1048576
[ 0.000000] Normal 1048576 -> 1048576
[ 0.000000] early_node_map[3] active PFN ranges
[ 0.000000] 0: 1 -> 160
[ 0.000000] 0: 192 -> 240
[ 0.000000] 0: 256 -> 524288
[ 0.000000] Nvidia board detected. Ignoring ACPI timer override.
[ 0.000000] If you got timer trouble try acpi_use_timer_override
[ 0.000000] Intel MultiProcessor Specification v1.4
[ 0.000000] MPTABLE: OEM ID: GIGABYTE MPTABLE: Product ID: M57SLI
MPTABLE: APIC at: 0xFEE00000
[ 0.000000] Processor #0 (Bootup-CPU)
[ 0.000000] Processor #1
[ 0.000000] I/O APIC #2 at 0xFC044000.
[ 0.000000] Setting APIC routing to physical flat
[ 0.000000] Processors: 2
[ 0.000000] Nosave address range: 00000000000a0000 - 00000000000c0000
[ 0.000000] Nosave address range: 00000000000f0000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 88000000 (gap:
80000000:80000000)
[ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] PERCPU: Allocating 34048 bytes of per cpu data
[ 0.000000] Built 1 zonelists. Total pages: 515988
[ 0.000000] Kernel command line: acpi=off pci=noacpi,nobios console=tty0
console=ttyS0,115200 root=UUID=3bd44ac7-3a5b-4d3a-b452-fbbc051c9f8d ro
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
[ 18.078019] Console: colour dummy device 80x25
[ 18.300317] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 18.308675] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 18.316158] Checking aperture...
[ 18.319404] CPU 0: aperture @ f8000000 size 64 MB
[ 18.339604] Memory: 2053392k/2097152k available (2217k kernel code, 43564k
reserved, 1162k data, 304k init)
[ 18.427016] Calibrating delay using timer specific routine.. 4007.33
BogoMIPS (lpj=8014667)
[ 18.435440] Security Framework v1.0.0 initialized
[ 18.440151] SELinux: Disabled at boot.
[ 18.444010] Mount-cache hash table entries: 256
[ 18.448665] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 18.455797] CPU: L2 Cache: 512K (64 bytes/line)
[ 18.460328] CPU 0/0 -> Node 0
[ 18.463304] CPU: Physical Processor ID: 0
[ 18.467316] CPU: Processor Core ID: 0
[ 18.471002] SMP alternatives: switching to UP code
[ 18.476012] Early unpacking initramfs... done
[ 18.841396] Using local APIC timer interrupts.
[ 18.895747] result 12500066
[ 18.898537] Detected 12.500 MHz APIC timer.
[ 18.906311] SMP alternatives: switching to SMP code
[ 18.911283] Booting processor 1/2 APIC 0x1
[ 18.925636] Initializing CPU#1
[ 19.005911] Calibrating delay using timer specific routine.. 4000.28
BogoMIPS (lpj=8000579)
[ 19.005918] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 19.005920] CPU: L2 Cache: 512K (64 bytes/line)
[ 19.005922] CPU 1/1 -> Node 0
[ 19.005924] CPU: Physical Processor ID: 0
[ 19.005925] CPU: Processor Core ID: 1
[ 19.006002] AMD Athlon(tm) 64 X2 Dual Core Processor 3800+ stepping 02
[ 19.009908] CPU 1: Syncing TSC to CPU 0.
[ 19.010002] CPU 1: synchronized TSC with CPU 0 (last diff 0 cycles, maxerr
522 cycles)
[ 19.010013] Brought up 2 CPUs
[ 19.064956] time.c: Using 1.193182 MHz WALL PIT GTOD PIT/TSC timer.
[ 19.071213] time.c: Detected 2000.008 MHz processor.
[ 19.716265] migration_cost=165
[ 19.719685] Time: 1:46:20 Date: 08/16/107
[ 19.723909] NET: Registered protocol family 16
[ 19.728723] PCI: Using configuration type 1
[ 19.733435] ACPI: Interpreter disabled.
[ 19.737283] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 19.742943] pnp: PnP ACPI: disabled
[ 19.746482] PCI: Probing PCI hardware
[ 19.751869] PCI: Using IRQ router default [10de/0370] at 0000:00:06.0
[ 19.758339] PCI->APIC IRQ transform: 0000:00:01.1[A] -> IRQ 10
[ 19.764174] PCI->APIC IRQ transform: 0000:00:01.3[B] -> IRQ 10
[ 19.770000] PCI->APIC IRQ transform: 0000:00:02.0[A] -> IRQ 22
[ 19.775831] PCI->APIC IRQ transform: 0000:00:02.1[B] -> IRQ 23
[ 19.781661] PCI->APIC IRQ transform: 0000:00:05.0[A] -> IRQ 20
[ 19.787489] PCI->APIC IRQ transform: 0000:00:05.1[B] -> IRQ 23
[ 19.793319] PCI->APIC IRQ transform: 0000:00:05.2[C] -> IRQ 21
[ 19.799150] PCI->APIC IRQ transform: 0000:00:06.1[B] -> IRQ 23
[ 19.804979] PCI->APIC IRQ transform: 0000:00:08.0[A] -> IRQ 22
[ 19.810874] NET: Registered protocol family 8
[ 19.815230] NET: Registered protocol family 20
[ 19.820054] PCI: Bridge: 0000:00:06.0
[ 19.823726] IO window: disabled.
[ 19.827149] MEM window: disabled.
[ 19.830652] PREFETCH window: disabled.
[ 19.834579] PCI: Bridge: 0000:00:0a.0
[ 19.838245] IO window: disabled.
[ 19.841655] MEM window: disabled.
[ 19.845149] PREFETCH window: disabled.
[ 19.849075] PCI: Bridge: 0000:00:0b.0
[ 19.852743] IO window: disabled.
[ 19.856141] MEM window: disabled.
[ 19.859636] PREFETCH window: disabled.
[ 19.863565] PCI: Bridge: 0000:00:0c.0
[ 19.867231] IO window: disabled.
[ 19.870639] MEM window: disabled.
[ 19.874135] PREFETCH window: disabled.
[ 19.878061] PCI: Bridge: 0000:00:0d.0
[ 19.881727] IO window: disabled.
[ 19.885136] MEM window: disabled.
[ 19.888630] PREFETCH window: disabled.
[ 19.892558] PCI: Bridge: 0000:00:0e.0
[ 19.896224] IO window: disabled.
[ 19.899625] MEM window: disabled.
[ 19.903118] PREFETCH window: disabled.
[ 19.907046] PCI: Bridge: 0000:00:0f.0
[ 19.910712] IO window: disabled.
[ 19.914112] MEM window: disabled.
[ 19.917608] PREFETCH window: disabled.
[ 19.921614] NET: Registered protocol family 2
[ 19.964113] IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 19.971556] TCP established hash table entries: 262144 (order: 10, 4194304
bytes)
[ 19.980773] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 19.987907] TCP: Hash tables configured (established 262144 bind 65536)
[ 19.994518] TCP reno registered
[ 20.008083] checking if image is initramfs... it is
[ 20.616653] Freeing initrd memory: 7303k freed
[ 20.624816] audit: initializing netlink socket (disabled)
[ 20.630224] audit(1189907180.184:1): initialized
[ 20.634978] VFS: Disk quotas dquot_6.5.1
[ 20.638913] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 20.645400] io scheduler noop registered
[ 20.649339] io scheduler anticipatory registered
[ 20.653968] io scheduler deadline registered
[ 20.658259] io scheduler cfq registered (default)
[ 20.663247] assign_interrupt_mode Found MSI capability
[ 20.668456] assign_interrupt_mode Found MSI capability
[ 20.673667] assign_interrupt_mode Found MSI capability
[ 20.678871] assign_interrupt_mode Found MSI capability
[ 20.684076] assign_interrupt_mode Found MSI capability
[ 20.689273] assign_interrupt_mode Found MSI capability
[ 20.716245] Real Time Clock Driver v1.12ac
[ 20.720417] Linux agpgart interface v0.102 (c) Dave Jones
[ 20.725805] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing
enabled
[ 20.733642] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 20.740048] mice: PS/2 mouse device common for all mice
[ 20.745755] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024
blocksize
[ 20.753438] input: Macintosh mouse button emulation as /class/input/input0
[ 20.760323] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 20.766659] ide: Assuming 33MHz system bus speed for PIO modes; override
with idebus=xx
[ 20.774883] PNP: No PS/2 controller found. Probing ports directly.
[ 20.781319] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 20.786293] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 20.791428] TCP cubic registered
[ 20.794666] NET: Registered protocol family 1
[ 20.799060] Magic number: 7:558:761
[ 20.802838] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 20.809168] Freeing unused kernel memory: 304k freed
Loading, please wait...
[ 20.831939] input: AT Translated Set 2 keyboard as /class/input/input1
Begin: Loading essential drivers... ...
[ 20.960675] Capability LSM initialized
Done.
Begin: Running /scripts/init-premount ...
[ 21.034479] thermal: Unknown symbol acpi_processor_set_thermal_limit
Done.
Begin: Mounting root file system... ...
Begin: Running /scripts/local-top ...
Done.
Begin: Waiting for root file system... ...
[ 21.499780] SCSI subsystem initialized
[ 21.514209] ata1: SATA max UDMA/133 cmd 0x0000000000012000 ctl
0x0000000000012072 bmdma 0x0000000000011cd0 irq 20
[ 21.524900] ata2: SATA max UDMA/133 cmd 0x0000000000012010 ctl
0x0000000000012082 bmdma 0x0000000000011cd8 irq 20
[ 21.535258] scsi0 : sata_nv
[ 21.538144] usbcore: registered new interface driver usbfs
[ 21.543726] usbcore: registered new interface driver hub
[ 21.549127] usbcore: registered new device driver usb
[ 21.559131] forcedeth.c: Reverse Engineered nForce ethernet driver. Version
0.59.
[ 21.852354] ata1: SATA link down (SStatus 0 SControl 300)
[ 21.868057] ATA: abnormal status 0x7F on port 0x0000000000012007
[ 21.874135] scsi1 : sata_nv
[ 22.191689] ata2: SATA link down (SStatus 0 SControl 300)
[ 22.207402] ATA: abnormal status 0x7F on port 0x0000000000012017
[ 22.213528] ata3: SATA max UDMA/133 cmd 0x0000000000012020 ctl
0x0000000000012092 bmdma 0x0000000000011ce0 irq 23
[ 22.223881] ata4: SATA max UDMA/133 cmd 0x0000000000012030 ctl
0x00000000000120a2 bmdma 0x0000000000011ce8 irq 23
[ 22.234216] scsi2 : sata_nv
[ 22.550989] ata3: SATA link down (SStatus 0 SControl 300)
[ 22.566712] ATA: abnormal status 0x7F on port 0x0000000000012027
[ 22.572787] scsi3 : sata_nv
[ 22.890323] ata4: SATA link down (SStatus 0 SControl 300)
[ 22.906038] ATA: abnormal status 0x7F on port 0x0000000000012037
[ 22.912165] ata5: SATA max UDMA/133 cmd 0x0000000000012040 ctl
0x00000000000120b2 bmdma 0x0000000000011cf0 irq 21
[ 22.922533] ata6: SATA max UDMA/133 cmd 0x0000000000012050 ctl
0x00000000000120c2 bmdma 0x0000000000011cf8 irq 21
[ 22.932865] scsi4 : sata_nv
[ 23.249618] ata5: SATA link down (SStatus 0 SControl 300)
[ 23.265343] ATA: abnormal status 0x7F on port 0x0000000000012047
[ 23.271413] scsi5 : sata_nv
[ 23.588954] ata6: SATA link down (SStatus 0 SControl 300)
[ 23.604668] ATA: abnormal status 0x7F on port 0x0000000000012057
[ 23.610793] ehci_hcd 0000:00:02.1: EHCI Host Controller
[ 23.616170] ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus
number 1
[ 23.623646] ehci_hcd 0000:00:02.1: debug port 1
[ 23.628225] ehci_hcd 0000:00:02.1: irq 23, io mem 0xfc04a000
[ 23.633947] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec
2004
[ 23.641591] usb usb1: configuration #1 chosen from 1 choice
[ 23.647238] hub 1-0:1.0: USB hub found
[ 23.651031] hub 1-0:1.0: 10 ports detected
[ 23.762904] NFORCE-MCP55: IDE controller at PCI slot 0000:00:04.0
[ 23.769318] NFORCE-MCP55: chipset revision 161
[ 23.773795] NFORCE-MCP55: not 100% native mode: will probe irqs later
[ 23.780275] NFORCE-MCP55: 0000:00:04.0 (rev a1) UDMA133 controller
[ 23.786492] ide0: BM-DMA at 0x1cc0-0x1cc7, BIOS settings: hda:pio,
hdb:pio
[ 24.084160] hda: ST340016A, ATA DISK drive
[ 24.762873] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 24.768977] ohci_hcd 0000:00:02.0: OHCI Host Controller
[ 24.774277] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus
number 2
[ 24.781716] ohci_hcd 0000:00:02.0: irq 22, io mem 0xfc045000
[ 24.848563] usb usb2: configuration #1 chosen from 1 choice
[ 24.854195] hub 2-0:1.0: USB hub found
[ 24.857973] hub 2-0:1.0: 10 ports detected
[ 24.966820] forcedeth: using HIGHDMA
[ 25.269672] usb 2-8: new low speed USB device using ohci_hcd and address 2
[ 25.492311] usb 2-8: configuration #1 chosen from 1 choice
[ 25.500116] eth0: forcedeth.c: subsystem: 01022:2b80 bound to 0000:00:08.0
[ 25.509935] usbcore: registered new interface driver hiddev
[ 25.522305] input: PS/2+USB Mouse as /class/input/input2
[ 25.527711] input: USB HID v1.11 Mouse [PS/2+USB Mouse] on usb-0000:00:02.0-8
[ 25.534949] usbcore: registered new interface driver usbhid
[ 25.540561] drivers/usb/input/hid-core.c: v2.6:USB HID core driver
[ 25.548611] hda: max request size: 128KiB
[ 25.553156] hda: Host Protected Area detected.
[ 25.553158] current capacity is 78163247 sectors (40019 MB)
[ 25.553160] native capacity is 78165360 sectors (40020 MB)
[ 25.569453] hda: Host Protected Area disabled.
[ 25.573945] hda: 78165360 sectors (40020 MB) w/2048KiB Cache,
CHS=65535/16/63, UDMA(33)
[ 25.582078] hda: cache flushes not supported
[ 25.586430] hda: hda1 hda2 hda3
Done.
Begin: Running /scripts/local-premount ...
kinit: name_to_d[ 25.812304] Attempting manual resume
ev_t(/dev/disk/by-uuid/c7601fc0-23eb-4c73-8ab6-9b407bb8b62a) = hda2(3,2)
kinit: trying to resume from
/dev/disk/by-uuid/c7601fc0-23eb-4c73-8ab6-9b407bb8b62a
kinit: No resume image, doing normal boot...
Done.
[ 25.840099] kjournald starting. Commit interval 5 seconds
[ 25.845657] EXT3-fs: mounted filesystem with ordered data mode.
Begin: Running /scripts/local-bottom ...
Done.
Done.
Begin: Running /scripts/init-bottom ...
Done.
* Reading files needed to boot... [80G [74G[ OK ]
* Setting preliminary keymap... [80G [74G[ OK ]
* Preparing restricted drivers... [80G [74G[ OK ]
* Starting basic networking... [80G [74G[ OK ]
* Starting kernel event manager... [80G [74G[ OK ]
* Loading hardware drivers... [80G [ 34.840143] eth2: no link during
initialization.
modprobe: FATAL: Error inserting af_packet
(/lib/modules/2.6.20-15-generic/kernel/net/packet/af_packet.ko): Invalid module
format
[74G[ OK ]
* Loading kernel modules... [80G * Loading manual drivers...
[80G [74G[ OK ]
* Activating swap... [80G [74G[ OK ]
* Checking root file system... [80G fsck 1.40-WIP (14-Nov-2006)
/dev/hda3: clean, 82253/2443200 files, 551350/4885768 blocks (check after next
mount)
[74G[ OK ]
* Checking file systems... [80G fsck 1.40-WIP (14-Nov-2006)
/dev/hda1: clean, 81447/2198880 files, 577764/4395777 blocks (check in 4 mounts)
[74G[ OK ]
* Mounting local filesystems... [80G [74G[ OK ]
* Activating swapfile swap... [80G [74G[ OK ]
* Configuring network interfaces... [80G modprobe: FATAL: Error
inserting af_packet
(/lib/modules/2.6.20-15-generic/kernel/net/packet/af_packet.ko): Invalid module
format
modprobe: FATAL: Error inserting af_packet
(/lib/modules/2.6.20-15-generic/kernel/net/packet/af_packet.ko): Invalid module
format
modprobe: FATAL: Error inserting af_packet
(/lib/modules/2.6.20-15-generic/kernel/net/packet/af_packet.ko): Invalid module
format
[74G[ OK ]
* Starting system log daemon... [80G [74G[ OK ]
* Doing Wacom setup... [80G cat: */id: No such file or directory
[74G[ OK ]
* Starting kernel log... [80G [74G[ OK ]
* Starting system message bus dbus [80G [74G[ OK ]
* Starting Hardware abstraction layer hald [80G
Ubuntu 7.04 sarcosuchus ttyS0
sarcosuchus login: [74G[ OK ]
* Starting DHCP D-Bus daemon dhcdbd [80G [74G[ OK ]
* Starting network connection manager NetworkManager [80G [74G[ OK ]
* Starting network events dispatcher NetworkManagerDispatcher [80G
[74G[ OK ]
* Starting Common Unix Printing System: cupsd [80G WARNING: Error
inserting parport
(/lib/modules/2.6.20-15-generic/kernel/drivers/parport/parport.ko): Invalid
module format
FATAL: Error inserting lp
(/lib/modules/2.6.20-15-generic/kernel/drivers/char/lp.ko): Invalid module
format
WARNING: Error inserting parport
(/lib/modules/2.6.20-15-generic/kernel/drivers/parport/parport.ko): Invalid
module format
FATAL: Error inserting ppdev
(/lib/modules/2.6.20-15-generic/kernel/drivers/char/ppdev.ko): Invalid module
format
[74G[ OK ]
* Starting HP Linux Printing and Imaging System [80G [74G[ OK ]
xserver-xorg postinst warning: overwriting possibly-customised configuration
file; backup in /etc/X11/xorg.conf.20070916034646
* Starting powernowd... [80G /etc/rc2.d/S20powernowd: 156: cannot
create /sys/devices/system/cpu/cpu0//cpufreq/scaling_governor: Directory
nonexistent
* CPU frequency scaling not supported
[74G[ OK ]
* Starting Bluetooth services [80G [74G[ OK ]
* Starting anac(h)ronistic cron anacron [80G [74G[ OK ]
* Starting deferred execution scheduler atd [80G [74G[ OK ]
* Starting periodic command scheduler crond [80G [74G[ OK ]
* Checking battery state... [80G [74G[ OK ]
Starting K Display Manager: kdm.
* Running local boot scripts (/etc/rc.local) [80G [74G[ OK ]
--
linuxbios mailing list
[email protected]
http://www.linuxbios.org/mailman/listinfo/linuxbios
