The change with the extra parenthesis (in the patch starting with line 133)
seems unecessary. I looked at the XLlDma_mBdWrite macro and it appeared to have
the correct use of parethesis in the implementation.
So, assuming there's nothing subtle that I missed, it's not needed. However, it
does no harm either.
The rest of the patch seems fine.
- John
On Wednesday 02 April 2008 00:20, Johann Baudy wrote:
> I've solved this checksum offloading issue with this below patch.
> It may help, if you need performance. It certainly needs review but it works
> on my side.
>
> --- xilinxgit/drivers/net/xilinx_lltemac/xlltemac_main.c.orig 2008-03-21
> 09:11:43.000000000 +0100
> +++ xilinxgit/drivers/net/xilinx_lltemac/xlltemac_main.c 2008-03-21
> 09:24:23.000000000 +0100
> @@ -133,7 +133,7 @@
> (XLlDma_mBdRead((BdPtr), XLLDMA_BD_STSCTRL_USR0_OFFSET)) &
> 0xFFFFFFFE )
>
> #define BdCsumSetup(BdPtr, Start, Insert) \
> - XLlDma_mBdWrite((BdPtr), XLLDMA_BD_USR1_OFFSET, (Start) << 16 |
> (Insert))
> + XLlDma_mBdWrite((BdPtr), XLLDMA_BD_USR1_OFFSET, ((Start) << 16) |
> (Insert))
>
> /* Used for debugging */
> #define BdCsumInsert(BdPtr) \
> @@ -1540,7 +1541,7 @@ static int xenet_DmaSend_internal(struct
> /*
> * if tx checksum offloading is enabled, when the ethernet stack
> * wants us to perform the checksum in hardware,
> - * skb->ip_summed is CHECKSUM_COMPLETE. Otherwise skb->ip_summed is
> + * skb->ip_summed is CHECKSUM_PARTIAL. Otherwise skb->ip_summed is
> * CHECKSUM_NONE, meaning the checksum is already done, or
> * CHECKSUM_UNNECESSARY, meaning checksumming is turned off (e.g.
> * loopback interface)
> @@ -1565,9 +1566,11 @@ static int xenet_DmaSend_internal(struct
> * skb_transport_header(skb) points to the beginning of the ip header
> *
> */
> - if (skb->ip_summed == CHECKSUM_COMPLETE) {
> + if (skb->ip_summed == CHECKSUM_PARTIAL) {
> +
> + unsigned int csum_start_off = skb_transport_offset(skb);
> + unsigned int csum_index_off = csum_start_off + skb->csum_offset;
>
> - unsigned char *raw = skb_transport_header(skb);
> #if 0
> {
> unsigned int csum = _xenet_tx_csum(skb);
> @@ -1578,9 +1581,8 @@ static int xenet_DmaSend_internal(struct
> }
> #else
> BdCsumEnable(bd_ptr);
> - BdCsumSetup(bd_ptr, raw - skb->data,
> - (raw - skb->data) + skb->csum);
> -
> + BdCsumSetup(bd_ptr, csum_start_off,
> + csum_index_off);
> #endif
> lp->tx_hw_csums++;
> }
> @@ -3277,7 +3279,7 @@ static int __devinit xtenet_of_probe(str
> struct resource *r_irq = &r_irq_struct; /* Interrupt resources */
> struct resource *r_mem = &r_mem_struct; /* IO mem resources */
> struct xlltemac_platform_data *pdata = &pdata_struct;
> - void *mac_address;
> + const void *mac_address;
> int rc = 0;
> const phandle *llink_connected_handle;
> struct device_node *llink_connected_node;
>
>
> On Mon, Mar 31, 2008 at 11:10 AM, Magnus Hjorth <[EMAIL PROTECTED]> wrote:
>
> > Deactivating checksum offloading helped a lot! I still have some packet
> > loss and not the best performance (TFTP transfer about 100 kbyte/s) but at
> > least it works.
> >
> > Thanks!
> >
> > //Magnus
> >
> > > -----Original Message-----
> > > From: rza1 [mailto:[EMAIL PROTECTED]
> > > Sent: den 31 mars 2008 11:14
> > > To: Magnus Hjorth
> > > Cc: John Linn; git; linuxppc-embedded@ozlabs.org
> > > Subject: Re: Xilinx LLTEMAC driver issues
> > >
> > > Hi Magnus,
> > >
> > > 1.
> > > I am using nearly the same versions then you and got the same problems
> > > too ;-).
> > > I think there are some problems with the checksum offloading.
> > > Try to sniff the some packages (e.g. wireshark)...
> > > For me ICMP (ping) worked but udp and tcp not (because off a wrong
> > > checksum in the transport layer).
> > > A quick solution is to just deactivate checksum offloading.
> > >
> > > 2.
> > > I remember some problems with Virtex-4 presamples too.
> > > There where problems with the hard-temac wrapper. You had to use 1.00.a
> > > and not b version.
> > > But I don't have these problems with the EDK 9.2sp2/ISE9.2sp3 anymore.
> > >
> > > all the best,
> > > Robert
> > >
> > > Magnus Hjorth wrote:
> > > > Hi John,
> > > >
> > > > Thanks for the very fast reply! Right now I'm not at work so I don't
> > > > have the board or EDK here to test anything.
> > > >
> > > > I'm using checksum offload, but I don't know if DRE is enabled or not.
> > I
> > > > can't recall seeing any setting to enable/disable DRE..
> > > >
> > > > A few things that crossed my mind:
> > > >
> > > > Last year I did a design with EDK 8.2, back then there was an issue
> > with
> > > > the ML403 boards having an old revision of the FPGA which wasn't
> > > > compatible with some versions of the IP core. There are no such
> > version
> > > > issues with the xps_ll_temac?
> > > >
> > > > I don't think that I had phy-addr set in the DTS file. Will test that
> > on
> > > > Monday.
> > > >
> > > > Best regards,
> > > > Magnus
> > > >
> > > >
> > > > On Sat, 2008-03-29 at 07:58 -0600, John Linn wrote:
> > > >
> > > >> Hi Magnus,
> > > >>
> > > >> Sorry to hear you're having problems with it.
> > > >>
> > > >> I am doing testing on an ML405 which is the same board but with a
> > bigger
> > > FPGA, but with ppc arch and I don't see this issue. I have done limited
> > testing
> > > with powerpc arch and the LL TEMAC, but I didn't see this issue there
> > either.
> > > Powerpc arch is definitely less mature in my experience than the ppc
> > arch. I'll
> > > do a quick test with my powerpc arch and make sure again I'm not seeing
> > it.
> > > >>
> > > >> My kernel is from the Xilinx Git tree, but there have been a number
> > of
> > > changes we have pushed out so I don't know how long ago you pulled from
> > the Git
> > > tree.
> > > >>
> > > >> My EDK project is 10.1 so it's a little newer. I am using LL TEMAC
> > 1.01a so
> > > it's a little newer. I reviewed the change log for the LL TEMAC and
> > don't see
> > > any big problems that were fixed in the newer versions, more new
> > features. I'll
> > > check with some others here to see if I missed something there.
> > > >>
> > > >> I am using DMA also, but no DRE or checksum offload. You didn't say
> > anything
> > > about those. I'm going to insert my mhs file that describes my system to
> > let you
> > > compare your system configuration. It's not clear to me yet if you have
> > a h/w or
> > > s/w problem.
> > > >>
> > > >> I'll also insert some of my device tree with the LL TEMAC so you can
> > compare
> > > (ignore 16550 stuff as we are still working on that).
> > > >>
> > > >> Since you can't ping reliably I would probably focus on that since
> > it's
> > > simpler than the other issues you're seeing.
> > > >>
> > > >> Thanks,
> > > >> John
> > > >>
> > > >>
> > > >>
> > > >> #
> > >
> > ##############################################################################
> > > >> # Created by Base System Builder Wizard for Xilinx EDK 10.1.1 Build
> > > EDK_K_SP1.1
> > > >> # Thu Feb 14 14:11:12 2008
> > > >> # Target Board: Xilinx Virtex 4 ML405 Evaluation Platform Rev 1
> > > >> # Family: virtex4
> > > >> # Device: xc4vfx20
> > > >> # Package: ff672
> > > >> # Speed Grade: -10
> > > >> # Processor: ppc405_0
> > > >> # Processor clock frequency: 300.00 MHz
> > > >> # Bus clock frequency: 100.00 MHz
> > > >> # On Chip Memory : 8 KB
> > > >> # Total Off Chip Memory : 128 MB
> > > >> # - DDR_SDRAM = 128 MB
> > > >> #
> > >
> > ##############################################################################
> > > >> PARAMETER VERSION = 2.1.0
> > > >>
> > > >>
> > > >> PORT fpga_0_RS232_Uart_sin_pin = fpga_0_RS232_Uart_sin, DIR = I
> > > >> PORT fpga_0_RS232_Uart_sout_pin = fpga_0_RS232_Uart_sout, DIR = O
> > > >> PORT fpga_0_LEDs_4Bit_GPIO_IO_pin = fpga_0_LEDs_4Bit_GPIO_IO, DIR =
> > IO, VEC
> > > = [0:3]
> > > >> PORT fpga_0_IIC_EEPROM_Scl_pin = fpga_0_IIC_EEPROM_Scl, DIR = IO
> > > >> PORT fpga_0_IIC_EEPROM_Sda_pin = fpga_0_IIC_EEPROM_Sda, DIR = IO
> > > >> PORT fpga_0_SysACE_CompactFlash_SysACE_CLK_pin =
> > > fpga_0_SysACE_CompactFlash_SysACE_CLK, DIR = I
> > > >> PORT fpga_0_SysACE_CompactFlash_SysACE_MPA_pin =
> > > fpga_0_SysACE_CompactFlash_SysACE_MPA, DIR = O, VEC = [6:1]
> > > >> PORT fpga_0_SysACE_CompactFlash_SysACE_MPD_pin =
> > > fpga_0_SysACE_CompactFlash_SysACE_MPD, DIR = IO, VEC = [15:0]
> > > >> PORT fpga_0_SysACE_CompactFlash_SysACE_CEN_pin =
> > > fpga_0_SysACE_CompactFlash_SysACE_CEN, DIR = O
> > > >> PORT fpga_0_SysACE_CompactFlash_SysACE_OEN_pin =
> > > fpga_0_SysACE_CompactFlash_SysACE_OEN, DIR = O
> > > >> PORT fpga_0_SysACE_CompactFlash_SysACE_WEN_pin =
> > > fpga_0_SysACE_CompactFlash_SysACE_WEN, DIR = O
> > > >> PORT fpga_0_SysACE_CompactFlash_SysACE_MPIRQ_pin =
> > > fpga_0_SysACE_CompactFlash_SysACE_MPIRQ, DIR = I
> > > >> PORT fpga_0_DDR_SDRAM_DDR_Clk_pin = fpga_0_DDR_SDRAM_DDR_Clk, DIR =
> > O
> > > >> PORT fpga_0_DDR_SDRAM_DDR_Clk_n_pin = fpga_0_DDR_SDRAM_DDR_Clk_n,
> > DIR = O
> > > >> PORT fpga_0_DDR_SDRAM_DDR_Addr_pin = fpga_0_DDR_SDRAM_DDR_Addr, DIR
> > = O, VEC
> > > = [12:0]
> > > >> PORT fpga_0_DDR_SDRAM_DDR_BankAddr_pin =
> > fpga_0_DDR_SDRAM_DDR_BankAddr, DIR
> > > = O, VEC = [1:0]
> > > >> PORT fpga_0_DDR_SDRAM_DDR_CAS_n_pin = fpga_0_DDR_SDRAM_DDR_CAS_n,
> > DIR = O
> > > >> PORT fpga_0_DDR_SDRAM_DDR_CE_pin = fpga_0_DDR_SDRAM_DDR_CE, DIR = O
> > > >> PORT fpga_0_DDR_SDRAM_DDR_CS_n_pin = fpga_0_DDR_SDRAM_DDR_CS_n, DIR
> > = O
> > > >> PORT fpga_0_DDR_SDRAM_DDR_RAS_n_pin = fpga_0_DDR_SDRAM_DDR_RAS_n,
> > DIR = O
> > > >> PORT fpga_0_DDR_SDRAM_DDR_WE_n_pin = fpga_0_DDR_SDRAM_DDR_WE_n, DIR
> > = O
> > > >> PORT fpga_0_DDR_SDRAM_DDR_DM_pin = fpga_0_DDR_SDRAM_DDR_DM, DIR = O,
> > VEC =
> > > [3:0]
> > > >> PORT fpga_0_DDR_SDRAM_DDR_DQS = fpga_0_DDR_SDRAM_DDR_DQS, DIR = IO,
> > VEC =
> > > [3:0]
> > > >> PORT fpga_0_DDR_SDRAM_DDR_DQ = fpga_0_DDR_SDRAM_DDR_DQ, DIR = IO,
> > VEC =
> > > [31:0]
> > > >> PORT fpga_0_TriMode_MAC_GMII_GMII_TXD_0_pin =
> > > fpga_0_TriMode_MAC_GMII_GMII_TXD_0, DIR = O, VEC = [7:0]
> > > >> PORT fpga_0_TriMode_MAC_GMII_GMII_TX_EN_0_pin =
> > > fpga_0_TriMode_MAC_GMII_GMII_TX_EN_0, DIR = O
> > > >> PORT fpga_0_TriMode_MAC_GMII_GMII_TX_ER_0_pin =
> > > fpga_0_TriMode_MAC_GMII_GMII_TX_ER_0, DIR = O
> > > >> PORT fpga_0_TriMode_MAC_GMII_GMII_TX_CLK_0_pin =
> > > fpga_0_TriMode_MAC_GMII_GMII_TX_CLK_0, DIR = O
> > > >> PORT fpga_0_TriMode_MAC_GMII_GMII_RXD_0_pin =
> > > fpga_0_TriMode_MAC_GMII_GMII_RXD_0, DIR = I, VEC = [7:0]
> > > >> PORT fpga_0_TriMode_MAC_GMII_GMII_RX_DV_0_pin =
> > > fpga_0_TriMode_MAC_GMII_GMII_RX_DV_0, DIR = I
> > > >> PORT fpga_0_TriMode_MAC_GMII_GMII_RX_ER_0_pin =
> > > fpga_0_TriMode_MAC_GMII_GMII_RX_ER_0, DIR = I
> > > >> PORT fpga_0_TriMode_MAC_GMII_GMII_RX_CLK_0_pin =
> > > fpga_0_TriMode_MAC_GMII_GMII_RX_CLK_0, DIR = I
> > > >> PORT fpga_0_TriMode_MAC_GMII_MII_TX_CLK_0_pin =
> > > fpga_0_TriMode_MAC_GMII_MII_TX_CLK_0, DIR = I
> > > >> PORT fpga_0_TriMode_MAC_GMII_MDIO_0_pin =
> > fpga_0_TriMode_MAC_GMII_MDIO_0,
> > > DIR = IO
> > > >> PORT fpga_0_TriMode_MAC_GMII_MDC_0_pin =
> > fpga_0_TriMode_MAC_GMII_MDC_0, DIR
> > > = O
> > > >> PORT fpga_0_TriMode_MAC_GMII_TemacPhy_RST_n_pin =
> > > fpga_0_TriMode_MAC_GMII_TemacPhy_RST_n, DIR = O
> > > >> PORT sys_clk_pin = dcm_clk_s, DIR = I, SIGIS = CLK, CLK_FREQ =
> > 100000000
> > > >> PORT sys_rst_pin = sys_rst_s, DIR = I, RST_POLARITY = 0, SIGIS = RST
> > > >>
> > > >>
> > > >> BEGIN ppc405_virtex4
> > > >> PARAMETER INSTANCE = ppc405_0
> > > >> PARAMETER HW_VER = 2.01.a
> > > >> PARAMETER C_FASTEST_PLB_CLOCK = DPLB1
> > > >> PARAMETER C_IDCR_BASEADDR = 0b0100000000
> > > >> PARAMETER C_IDCR_HIGHADDR = 0b0111111111
> > > >> BUS_INTERFACE JTAGPPC = jtagppc_0_0
> > > >> BUS_INTERFACE IPLB0 = plb
> > > >> BUS_INTERFACE DPLB0 = plb
> > > >> BUS_INTERFACE IPLB1 = ppc405_0_iplb1
> > > >> BUS_INTERFACE DPLB1 = ppc405_0_dplb1
> > > >> BUS_INTERFACE RESETPPC = ppc_reset_bus
> > > >> PORT CPMC405CLOCK = proc_clk_s
> > > >> PORT EICC405EXTINPUTIRQ = EICC405EXTINPUTIRQ
> > > >> END
> > > >>
> > > >> BEGIN jtagppc_cntlr
> > > >> PARAMETER INSTANCE = jtagppc_0
> > > >> PARAMETER HW_VER = 2.01.a
> > > >> BUS_INTERFACE JTAGPPC0 = jtagppc_0_0
> > > >> END
> > > >>
> > > >> BEGIN plb_v46
> > > >> PARAMETER INSTANCE = plb
> > > >> PARAMETER C_DCR_INTFCE = 0
> > > >> PARAMETER C_NUM_CLK_PLB2OPB_REARB = 100
> > > >> PARAMETER HW_VER = 1.02.a
> > > >> PORT PLB_Clk = sys_clk_s
> > > >> PORT SYS_Rst = sys_bus_reset
> > > >> END
> > > >>
> > > >> BEGIN xps_bram_if_cntlr
> > > >> PARAMETER INSTANCE = xps_bram_if_cntlr_1
> > > >> PARAMETER HW_VER = 1.00.a
> > > >> PARAMETER C_SPLB_NATIVE_DWIDTH = 64
> > > >> PARAMETER C_BASEADDR = 0xffffe000
> > > >> PARAMETER C_HIGHADDR = 0xffffffff
> > > >> BUS_INTERFACE SPLB = plb
> > > >> BUS_INTERFACE PORTA = xps_bram_if_cntlr_1_port
> > > >> END
> > > >>
> > > >> BEGIN bram_block
> > > >> PARAMETER INSTANCE = plb_bram_if_cntlr_1_bram
> > > >> PARAMETER HW_VER = 1.00.a
> > > >> BUS_INTERFACE PORTA = xps_bram_if_cntlr_1_port
> > > >> END
> > > >>
> > > >> BEGIN xps_uart16550
> > > >> PARAMETER INSTANCE = RS232_Uart
> > > >> PARAMETER HW_VER = 2.00.a
> > > >> PARAMETER C_IS_A_16550 = 1
> > > >> PARAMETER C_BASEADDR = 0x83e00000
> > > >> PARAMETER C_HIGHADDR = 0x83e0ffff
> > > >> BUS_INTERFACE SPLB = plb
> > > >> PORT sin = fpga_0_RS232_Uart_sin
> > > >> PORT sout = fpga_0_RS232_Uart_sout
> > > >> PORT IP2INTC_Irpt = RS232_Uart_IP2INTC_Irpt
> > > >> END
> > > >>
> > > >> BEGIN xps_gpio
> > > >> PARAMETER INSTANCE = LEDs_4Bit
> > > >> PARAMETER HW_VER = 1.00.a
> > > >> PARAMETER C_INTERRUPT_PRESENT = 1
> > > >> PARAMETER C_GPIO_WIDTH = 4
> > > >> PARAMETER C_IS_DUAL = 0
> > > >> PARAMETER C_IS_BIDIR = 1
> > > >> PARAMETER C_ALL_INPUTS = 0
> > > >> PARAMETER C_BASEADDR = 0x81400000
> > > >> PARAMETER C_HIGHADDR = 0x8140ffff
> > > >> BUS_INTERFACE SPLB = plb
> > > >> PORT GPIO_IO = fpga_0_LEDs_4Bit_GPIO_IO
> > > >> PORT IP2INTC_Irpt = LEDs_4Bit_IP2INTC_Irpt
> > > >> END
> > > >>
> > > >> BEGIN xps_iic
> > > >> PARAMETER INSTANCE = IIC_EEPROM
> > > >> PARAMETER HW_VER = 2.00.a
> > > >> PARAMETER C_CLK_FREQ = 100000000
> > > >> PARAMETER C_IIC_FREQ = 100000
> > > >> PARAMETER C_TEN_BIT_ADR = 0
> > > >> PARAMETER C_BASEADDR = 0x81600000
> > > >> PARAMETER C_HIGHADDR = 0x8160ffff
> > > >> BUS_INTERFACE SPLB = plb
> > > >> PORT Scl = fpga_0_IIC_EEPROM_Scl
> > > >> PORT Sda = fpga_0_IIC_EEPROM_Sda
> > > >> PORT IIC2INTC_Irpt = IIC_EEPROM_IIC2INTC_Irpt
> > > >> END
> > > >>
> > > >> BEGIN xps_sysace
> > > >> PARAMETER INSTANCE = SysACE_CompactFlash
> > > >> PARAMETER HW_VER = 1.00.a
> > > >> PARAMETER C_MEM_WIDTH = 16
> > > >> PARAMETER C_BASEADDR = 0x83600000
> > > >> PARAMETER C_HIGHADDR = 0x8360ffff
> > > >> BUS_INTERFACE SPLB = plb
> > > >> PORT SysACE_CLK = fpga_0_SysACE_CompactFlash_SysACE_CLK
> > > >> PORT SysACE_MPA = fpga_0_SysACE_CompactFlash_SysACE_MPA_split
> > > >> PORT SysACE_MPD = fpga_0_SysACE_CompactFlash_SysACE_MPD
> > > >> PORT SysACE_CEN = fpga_0_SysACE_CompactFlash_SysACE_CEN
> > > >> PORT SysACE_OEN = fpga_0_SysACE_CompactFlash_SysACE_OEN
> > > >> PORT SysACE_WEN = fpga_0_SysACE_CompactFlash_SysACE_WEN
> > > >> PORT SysACE_MPIRQ = fpga_0_SysACE_CompactFlash_SysACE_MPIRQ
> > > >> PORT SysACE_IRQ = SysACE_CompactFlash_SysACE_IRQ
> > > >> END
> > > >>
> > > >> BEGIN mpmc
> > > >> PARAMETER INSTANCE = DDR_SDRAM
> > > >> PARAMETER HW_VER = 4.00.a
> > > >> PARAMETER C_NUM_PORTS = 3
> > > >> PARAMETER C_MEM_PARTNO = HYB25D512160BE-5
> > > >> PARAMETER C_MEM_DATA_WIDTH = 32
> > > >> PARAMETER C_MEM_DQS_WIDTH = 4
> > > >> PARAMETER C_MEM_DM_WIDTH = 4
> > > >> PARAMETER C_MEM_TYPE = DDR
> > > >> PARAMETER C_NUM_IDELAYCTRL = 2
> > > >> PARAMETER C_IDELAYCTRL_LOC = IDELAYCTRL_X0Y3-IDELAYCTRL_X0Y2
> > > >> PARAMETER C_PIM0_BASETYPE = 2
> > > >> PARAMETER C_PIM1_BASETYPE = 2
> > > >> PARAMETER C_PIM2_BASETYPE = 3
> > > >> PARAMETER C_MPMC_CLK0_PERIOD_PS = 10000
> > > >> PARAMETER C_SDMA2_PI2LL_CLK_RATIO = 1
> > > >> PARAMETER C_MPMC_BASEADDR = 0x00000000
> > > >> PARAMETER C_MPMC_HIGHADDR = 0x07ffffff
> > > >> PARAMETER C_SDMA_CTRL_BASEADDR = 0x84600000
> > > >> PARAMETER C_SDMA_CTRL_HIGHADDR = 0x8460ffff
> > > >> BUS_INTERFACE SPLB0 = ppc405_0_iplb1
> > > >> BUS_INTERFACE SPLB1 = ppc405_0_dplb1
> > > >> BUS_INTERFACE SDMA_LL2 = TriMode_MAC_GMII_LLINK0
> > > >> BUS_INTERFACE SDMA_CTRL2 = plb
> > > >> PORT DDR_Addr = fpga_0_DDR_SDRAM_DDR_Addr
> > > >> PORT DDR_BankAddr = fpga_0_DDR_SDRAM_DDR_BankAddr
> > > >> PORT DDR_CAS_n = fpga_0_DDR_SDRAM_DDR_CAS_n
> > > >> PORT DDR_CE = fpga_0_DDR_SDRAM_DDR_CE
> > > >> PORT DDR_CS_n = fpga_0_DDR_SDRAM_DDR_CS_n
> > > >> PORT DDR_RAS_n = fpga_0_DDR_SDRAM_DDR_RAS_n
> > > >> PORT DDR_WE_n = fpga_0_DDR_SDRAM_DDR_WE_n
> > > >> PORT DDR_DM = fpga_0_DDR_SDRAM_DDR_DM
> > > >> PORT DDR_DQS = fpga_0_DDR_SDRAM_DDR_DQS
> > > >> PORT DDR_DQ = fpga_0_DDR_SDRAM_DDR_DQ
> > > >> PORT DDR_Clk = fpga_0_DDR_SDRAM_DDR_Clk
> > > >> PORT DDR_Clk_n = fpga_0_DDR_SDRAM_DDR_Clk_n
> > > >> PORT MPMC_Clk0 = sys_clk_s
> > > >> PORT MPMC_Clk90 = DDR_SDRAM_mpmc_clk_90_s
> > > >> PORT SDMA2_Clk = sys_clk_s
> > > >> PORT MPMC_Clk_200MHz = clk_200mhz_s
> > > >> PORT MPMC_Rst = sys_periph_reset
> > > >> PORT SDMA2_Rx_IntOut = DDR_SDRAM_SDMA2_Rx_IntOut
> > > >> PORT SDMA2_Tx_IntOut = DDR_SDRAM_SDMA2_Tx_IntOut
> > > >> END
> > > >>
> > > >> BEGIN xps_ll_temac
> > > >> PARAMETER INSTANCE = TriMode_MAC_GMII
> > > >> PARAMETER HW_VER = 1.01.a
> > > >> PARAMETER C_SPLB_CLK_PERIOD_PS = 10000
> > > >> PARAMETER C_PHY_TYPE = 1
> > > >> PARAMETER C_NUM_IDELAYCTRL = 4
> > > >> PARAMETER C_IDELAYCTRL_LOC = IDELAYCTRL_X1Y1-IDELAYCTRL_X1Y3-
> > > IDELAYCTRL_X2Y2-IDELAYCTRL_X2Y3
> > > >> PARAMETER C_TEMAC_TYPE = 1
> > > >> PARAMETER C_BUS2CORE_CLK_RATIO = 1
> > > >> PARAMETER C_BASEADDR = 0x81c00000
> > > >> PARAMETER C_HIGHADDR = 0x81c0ffff
> > > >> BUS_INTERFACE SPLB = plb
> > > >> BUS_INTERFACE LLINK0 = TriMode_MAC_GMII_LLINK0
> > > >> PORT GMII_TXD_0 = fpga_0_TriMode_MAC_GMII_GMII_TXD_0
> > > >> PORT GMII_TX_EN_0 = fpga_0_TriMode_MAC_GMII_GMII_TX_EN_0
> > > >> PORT GMII_TX_ER_0 = fpga_0_TriMode_MAC_GMII_GMII_TX_ER_0
> > > >> PORT GMII_TX_CLK_0 = fpga_0_TriMode_MAC_GMII_GMII_TX_CLK_0
> > > >> PORT GMII_RXD_0 = fpga_0_TriMode_MAC_GMII_GMII_RXD_0
> > > >> PORT GMII_RX_DV_0 = fpga_0_TriMode_MAC_GMII_GMII_RX_DV_0
> > > >> PORT GMII_RX_ER_0 = fpga_0_TriMode_MAC_GMII_GMII_RX_ER_0
> > > >> PORT GMII_RX_CLK_0 = fpga_0_TriMode_MAC_GMII_GMII_RX_CLK_0
> > > >> PORT MII_TX_CLK_0 = fpga_0_TriMode_MAC_GMII_MII_TX_CLK_0
> > > >> PORT MDIO_0 = fpga_0_TriMode_MAC_GMII_MDIO_0
> > > >> PORT MDC_0 = fpga_0_TriMode_MAC_GMII_MDC_0
> > > >> PORT TemacPhy_RST_n = fpga_0_TriMode_MAC_GMII_TemacPhy_RST_n
> > > >> PORT GTX_CLK_0 = temac_clk_s
> > > >> PORT REFCLK = clk_200mhz_s
> > > >> PORT LlinkTemac0_CLK = sys_clk_s
> > > >> PORT TemacIntc0_Irpt = TriMode_MAC_GMII_TemacIntc0_Irpt
> > > >> END
> > > >>
> > > >> BEGIN util_bus_split
> > > >> PARAMETER INSTANCE = SysACE_CompactFlash_util_bus_split_0
> > > >> PARAMETER HW_VER = 1.00.a
> > > >> PARAMETER C_SIZE_IN = 7
> > > >> PARAMETER C_LEFT_POS = 0
> > > >> PARAMETER C_SPLIT = 6
> > > >> PORT Sig = fpga_0_SysACE_CompactFlash_SysACE_MPA_split
> > > >> PORT Out1 = fpga_0_SysACE_CompactFlash_SysACE_MPA
> > > >> END
> > > >>
> > > >> BEGIN plb_v46
> > > >> PARAMETER INSTANCE = ppc405_0_iplb1
> > > >> PARAMETER HW_VER = 1.02.a
> > > >> PORT PLB_Clk = sys_clk_s
> > > >> PORT SYS_Rst = sys_bus_reset
> > > >> END
> > > >>
> > > >> BEGIN plb_v46
> > > >> PARAMETER INSTANCE = ppc405_0_dplb1
> > > >> PARAMETER HW_VER = 1.02.a
> > > >> PORT PLB_Clk = sys_clk_s
> > > >> PORT SYS_Rst = sys_bus_reset
> > > >> END
> > > >>
> > > >> BEGIN clock_generator
> > > >> PARAMETER INSTANCE = clock_generator_0
> > > >> PARAMETER HW_VER = 2.00.a
> > > >> PARAMETER C_EXT_RESET_HIGH = 1
> > > >> PARAMETER C_CLKIN_FREQ = 100000000
> > > >> PARAMETER C_CLKOUT0_FREQ = 100000000
> > > >> PARAMETER C_CLKOUT0_BUF = TRUE
> > > >> PARAMETER C_CLKOUT0_PHASE = 0
> > > >> PARAMETER C_CLKOUT0_GROUP = DCM0
> > > >> PARAMETER C_CLKOUT1_FREQ = 100000000
> > > >> PARAMETER C_CLKOUT1_BUF = TRUE
> > > >> PARAMETER C_CLKOUT1_PHASE = 90
> > > >> PARAMETER C_CLKOUT1_GROUP = DCM0
> > > >> PARAMETER C_CLKOUT2_FREQ = 300000000
> > > >> PARAMETER C_CLKOUT2_BUF = TRUE
> > > >> PARAMETER C_CLKOUT2_PHASE = 0
> > > >> PARAMETER C_CLKOUT2_GROUP = DCM0
> > > >> PARAMETER C_CLKOUT3_FREQ = 200000000
> > > >> PARAMETER C_CLKOUT3_BUF = TRUE
> > > >> PARAMETER C_CLKOUT3_PHASE = 0
> > > >> PARAMETER C_CLKOUT3_GROUP = NONE
> > > >> PARAMETER C_CLKOUT4_FREQ = 125000000
> > > >> PARAMETER C_CLKOUT4_BUF = TRUE
> > > >> PARAMETER C_CLKOUT4_PHASE = 0
> > > >> PARAMETER C_CLKOUT4_GROUP = NONE
> > > >> PORT CLKOUT0 = sys_clk_s
> > > >> PORT CLKOUT1 = DDR_SDRAM_mpmc_clk_90_s
> > > >> PORT CLKOUT2 = proc_clk_s
> > > >> PORT CLKOUT3 = clk_200mhz_s
> > > >> PORT CLKOUT4 = temac_clk_s
> > > >> PORT CLKIN = dcm_clk_s
> > > >> PORT LOCKED = Dcm_all_locked
> > > >> PORT RST = net_gnd
> > > >> END
> > > >>
> > > >> BEGIN proc_sys_reset
> > > >> PARAMETER INSTANCE = proc_sys_reset_0
> > > >> PARAMETER HW_VER = 2.00.a
> > > >> PARAMETER C_EXT_RESET_HIGH = 0
> > > >> BUS_INTERFACE RESETPPC0 = ppc_reset_bus
> > > >> PORT Slowest_sync_clk = sys_clk_s
> > > >> PORT Dcm_locked = Dcm_all_locked
> > > >> PORT Ext_Reset_In = sys_rst_s
> > > >> PORT Bus_Struct_Reset = sys_bus_reset
> > > >> PORT Peripheral_Reset = sys_periph_reset
> > > >> END
> > > >>
> > > >> BEGIN xps_intc
> > > >> PARAMETER INSTANCE = xps_intc_0
> > > >> PARAMETER HW_VER = 1.00.a
> > > >> PARAMETER C_BASEADDR = 0x81800000
> > > >> PARAMETER C_HIGHADDR = 0x8180ffff
> > > >> BUS_INTERFACE SPLB = plb
> > > >> PORT Irq = EICC405EXTINPUTIRQ
> > > >> PORT Intr = RS232_Uart_IP2INTC_Irpt & LEDs_4Bit_IP2INTC_Irpt &
> > > IIC_EEPROM_IIC2INTC_Irpt & SysACE_CompactFlash_SysACE_IRQ &
> > > TriMode_MAC_GMII_TemacIntc0_Irpt & DDR_SDRAM_SDMA2_Rx_IntOut &
> > > DDR_SDRAM_SDMA2_Tx_IntOut
> > > >> END
> > > >>
> > > >>
> > > >>
> > > >> #address-cells = <1>;
> > > >> #size-cells = <1>;
> > > >> compatible = "xlnx,virtex";
> > > >> model = "testing";
> > > >> DDR_SDRAM: [EMAIL PROTECTED] {
> > > >> device_type = "memory";
> > > >> reg = < 0 8000000 >;
> > > >> } ;
> > > >> chosen {
> > > >> bootargs = "console=ttyS0,9600 ip=on
> > > nfsroot=172.16.40.76:/v2pclients/jhl26,tcp";
> > > >> linux,stdout-path = "/[EMAIL PROTECTED]/[EMAIL PROTECTED]";
> > > >> } ;
> > > >> cpus {
> > > >> #address-cells = <1>;
> > > >> #cpus = <1>;
> > > >> #size-cells = <0>;
> > > >> ppc405_0: [EMAIL PROTECTED] {
> > > >> clock-frequency = <11e1a300>;
> > > >> compatible = "PowerPC,405", "ibm,ppc405";
> > > >> d-cache-line-size = <20>;
> > > >> d-cache-size = <4000>;
> > > >> device_type = "cpu";
> > > >> i-cache-line-size = <20>;
> > > >> i-cache-size = <4000>;
> > > >> model = "PowerPC,405";
> > > >> reg = <0>;
> > > >> timebase-frequency = <11e1a300>;
> > > >> xlnx,apu-control = <de00>;
> > > >> xlnx,apu-udi-1 = <a18983>;
> > > >> xlnx,apu-udi-2 = <a38983>;
> > > >> xlnx,apu-udi-3 = <a589c3>;
> > > >> xlnx,apu-udi-4 = <a789c3>;
> > > >> xlnx,apu-udi-5 = <a98c03>;
> > > >> xlnx,apu-udi-6 = <ab8c03>;
> > > >> xlnx,apu-udi-7 = <ad8c43>;
> > > >> xlnx,apu-udi-8 = <af8c43>;
> > > >> xlnx,deterministic-mult = <0>;
> > > >> xlnx,disable-operand-forwarding = <1>;
> > > >> xlnx,fastest-plb-clock = "DPLB0";
> > > >> xlnx,generate-plb-timespecs = <1>;
> > > >> xlnx,mmu-enable = <1>;
> > > >> xlnx,pvr-high = <0>;
> > > >> xlnx,pvr-low = <0>;
> > > >> } ;
> > > >> } ;
> > > >> plb: [EMAIL PROTECTED] {
> > > >> #address-cells = <1>;
> > > >> #size-cells = <1>;
> > > >> compatible = "xlnx,plb-v46-1.02.a";
> > > >> ranges ;
> > > >> IIC_EEPROM: [EMAIL PROTECTED] {
> > > >> compatible = "xlnx,xps-iic-2.00.a";
> > > >> interrupt-parent = <&xps_intc_0>;
> > > >> interrupts = < 4 2 >;
> > > >> reg = < 81600000 10000 >;
> > > >> xlnx,clk-freq = <5f5e100>;
> > > >> xlnx,family = "virtex4";
> > > >> xlnx,gpo-width = <1>;
> > > >> xlnx,iic-freq = <186a0>;
> > > >> xlnx,scl-inertial-delay = <0>;
> > > >> xlnx,sda-inertial-delay = <0>;
> > > >> xlnx,ten-bit-adr = <0>;
> > > >> } ;
> > > >> LEDs_4Bit: [EMAIL PROTECTED] {
> > > >> compatible = "xlnx,xps-gpio-1.00.a";
> > > >> interrupt-parent = <&xps_intc_0>;
> > > >> interrupts = < 5 2 >;
> > > >> reg = < 81400000 10000 >;
> > > >> xlnx,all-inputs = <0>;
> > > >> xlnx,all-inputs-2 = <0>;
> > > >> xlnx,dout-default = <0>;
> > > >> xlnx,dout-default-2 = <0>;
> > > >> xlnx,family = "virtex4";
> > > >> xlnx,gpio-width = <4>;
> > > >> xlnx,interrupt-present = <1>;
> > > >> xlnx,is-bidir = <1>;
> > > >> xlnx,is-bidir-2 = <1>;
> > > >> xlnx,is-dual = <0>;
> > > >> xlnx,tri-default = <ffffffff>;
> > > >> xlnx,tri-default-2 = <ffffffff>;
> > > >> } ;
> > > >> RS232_Uart: [EMAIL PROTECTED] {
> > > >> compatible = "xlnx,xps-uart16550-2.00.a";
> > > >> // compatible = "ns16550";
> > > >> device_type = "serial";
> > > >> interrupt-parent = <&xps_intc_0>;
> > > >> interrupts = < 6 2 >;
> > > >> reg = < 83e00000 10000 >;
> > > >> current-speed = <d#9600>;
> > > >> clock-frequency = <d#100000000>; /* added
> > > by jhl */
> > > >> reg-shift = <2>;
> > > >> xlnx,family = "virtex4";
> > > >> xlnx,has-external-rclk = <0>;
> > > >> xlnx,has-external-xin = <0>;
> > > >> xlnx,is-a-16550 = <1>;
> > > >> } ;
> > > >> SysACE_CompactFlash: [EMAIL PROTECTED] {
> > > >> compatible = "xlnx,xps-sysace-1.00.a";
> > > >> interrupt-parent = <&xps_intc_0>;
> > > >> interrupts = < 3 2 >;
> > > >> reg = < 83600000 10000 >;
> > > >> xlnx,family = "virtex4";
> > > >> xlnx,mem-width = <10>;
> > > >> } ;
> > > >> TriMode_MAC_GMII: [EMAIL PROTECTED] {
> > > >> #address-cells = <1>;
> > > >> #size-cells = <1>;
> > > >> compatible = "xlnx,compound";
> > > >> [EMAIL PROTECTED] {
> > > >> compatible = "xlnx,xps-ll-temac-
> > > 1.01.a";
> > > >> device_type = "network";
> > > >> interrupt-parent =
> > > <&xps_intc_0>;
> > > >> interrupts = < 2 2 >;
> > > >> llink-connected = <&PIM2>;
> > > >> local-mac-address = [ 02 00 00
> > > 00 00 01 ];
> > > >> reg = < 81c00000 40 >;
> > > >> xlnx,bus2core-clk-ratio = <1>;
> > > >> xlnx,phy-type = <1>;
> > > >> xlnx,phyaddr = <1>;
> > > >> xlnx,rxcsum = <0>;
> > > >> xlnx,rxfifo = <1000>;
> > > >> xlnx,temac-type = <1>;
> > > >> xlnx,txcsum = <0>;
> > > >> xlnx,txfifo = <1000>;
> > > >> } ;
> > > >> } ;
> > > >> [EMAIL PROTECTED] {
> > > >> #address-cells = <1>;
> > > >> #size-cells = <1>;
> > > >> compatible = "xlnx,mpmc-4.00.a";
> > > >> PIM2: [EMAIL PROTECTED] {
> > > >> compatible = "xlnx,ll-dma-
> > > 1.00.a";
> > > >> interrupt-parent =
> > > <&xps_intc_0>;
> > > >> interrupts = < 1 2 0 2 >;
> > > >> reg = < 84600100 80 >;
> > > >> } ;
> > > >> } ;
> > > >> xps_bram_if_cntlr_1: [EMAIL PROTECTED] {
> > > >> compatible = "xlnx,xps-bram-if-cntlr-
> > > 1.00.a";
> > > >> reg = < ffffe000 2000 >;
> > > >> xlnx,family = "virtex4";
> > > >> } ;
> > > >> xps_intc_0: [EMAIL PROTECTED] {
> > > >> #interrupt-cells = <2>;
> > > >> compatible = "xlnx,xps-intc-1.00.a";
> > > >> interrupt-controller ;
> > > >> reg = < 81800000 10000 >;
> > > >> xlnx,num-intr-inputs = <7>;
> > > >> } ;
> > > >> } ;
> > > >> ppc405_0_dplb1: [EMAIL PROTECTED] {
> > > >> #address-cells = <1>;
> > > >> #size-cells = <1>;
> > > >> compatible = "xlnx,plb-v46-1.02.a";
> > > >> ranges ;
> > > >> } ;
> > > >> } ;
> > > >>
> > > >>
> > > >>
> > > >> -----Original Message-----
> > > >> From: Magnus Hjorth [mailto:[EMAIL PROTECTED]
> > > >> Sent: Saturday, March 29, 2008 6:54 AM
> > > >> To: git
> > > >> Cc: linuxppc-embedded@ozlabs.org
> > > >> Subject: Xilinx LLTEMAC driver issues
> > > >>
> > > >> Hi,
> > > >>
> > > >> I'm having some networking troubles with the Xilinx LLTEMAC driver
> > from the
> > > >> Xilinx Linux git tree (powerpc arch) on an ML403 board. EDK9.2SP2,
> > > >> xps_ll_temac v1.00.b
> > > >>
> > > >> The weird thing is, that it sort of half works. It successfully makes
> > a DHCP
> > > >> request and gets its IP address. I tried setting up a tftpd server,
> > and I can
> > > >> see UDP requests coming in but the response doesn't seem to come out.
> > I also
> > > >> tried running a TCP server on the board, and it can see and accept
> > incoming
> > > >> connections but after that no data seems to get through. I can ping
> > out and
> > > >> get around 40% packet loss.
> > > >>
> > > >> Looking at /proc/interrupts, I can see both TxDma interrupts and
> > RxDma
> > > >> interrupts. No eth0 interrupts but that seems to be OK judging by the
> > driver
> > > >> source comments. Ifconfig shows no collistions, no dropped packets,
> > no
> > > errors,
> > > >> so the system seems to think that everything is OK.
> > > >>
> > > >> Clues anyone? I'm starting to run out of ideas...
> > > >>
> > > >> Best regards,
> > > >> Magnus
> > > >>
> > > >>
> > > >> --
> > > >>
> > > >> Magnus Hjorth, M.Sc.
> > > >> Omnisys Instruments AB
> > > >> Gruvgatan 8
> > > >> SE-421 30 Västra Frölunda, SWEDEN
> > > >> Phone: +46 31 734 34 09
> > > >> Fax: +46 31 734 34 29
> > > >> http://www.omnisys.se
> > > >>
> > > >
> > > > _______________________________________________
> > > > Linuxppc-embedded mailing list
> > > > Linuxppc-embedded@ozlabs.org
> > > > https://ozlabs.org/mailman/listinfo/linuxppc-embedded
> > _______________________________________________
> > Linuxppc-embedded mailing list
> > Linuxppc-embedded@ozlabs.org
> > https://ozlabs.org/mailman/listinfo/linuxppc-embedded
> >
>
>
>
> --
> Johann Baudy
> [EMAIL PROTECTED]
>
_______________________________________________
Linuxppc-embedded mailing list
Linuxppc-embedded@ozlabs.org
https://ozlabs.org/mailman/listinfo/linuxppc-embedded
