Yet another tool for configuring modeline: http://www.dkfz-heidelberg.de/spec/linux/modeline/
-----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of [EMAIL PROTECTED] Sent: Thursday, February 06, 2003 5:37 PM To: LTSP discussion list Subject: FW: Re: [Ltsp-discuss] Modeline About a month ago Pedro Noticioso has sent the following reply to this list. Maybe that helps. -----FW: <[EMAIL PROTECTED]>----- Date: Wed, 29 Jan 2003 11:44:36 -0800 (PST) Sender: [EMAIL PROTECTED] From: pedro noticioso <[EMAIL PROTECTED]> To: [EMAIL PROTECTED] Subject: Re: [Ltsp-discuss] Modeline This is a simple tool to automatically give you the correct modelines 8) http://www.hut.fi/Misc/Electronics/faq/vga2rgb/calc.html --- Jake Schroeder <[EMAIL PROTECTED]> wrote: > I found the manual for your Philips Brilliance 150P, > and in the Product > Information section it says this: > > Input Frequency > - XGA Hsync 48-60 KHz, Vsync 60-75 Hz (N.I.) > - SVGA Hsync 35-50 KHz, Vsync 56-75 Hz (N.I.) > - VGA Hsync 31-38 KHz, Vsync 60-75 Hz (N.I.) > > So for most purposes, I would use the XGA values. I > am not the modeline > master, so I do not know how to construct a modeline > that will support > all of the resolutions. But it seems that 75 Hz is > actually the best > recommended refresh rate - anything higher, and you > might get the error > that shows up when the monitor can't sync to the > video signal. Refresh > rate is not important in LCDs though; you can use 60 > Hz and not see the > difference. > > - Jake > > > > On Wed, Jan 29, 2003 at 05:24:07PM +0100, Alfred > Poschmann wrote: > > On Wednesday 29 January 2003 16:23, Jake Schroeder > wrote: > > > On Wed, Jan 29, 2003 at 04:04:30PM +0100, Tom > Schouteden wrote: > > > > hi, does anyone here have a modeline example > for TFT screens? on the > > > > clients my screen looks like it has vertical > "blurry fields". there > > > > appear to be some (imaginary) vertical columns > below which the fonts > > > > look more blurred/aliased than those next to > them. i think this may be > > > > caused by a wrong modeline. any other > suggestions are also welcome. > > > > > > > > (btw: my previous font spacing issue was > solved as soon as i enabled > > > > xfs) > > > > > The best solution is to find your monitor's > preferred sync rates at > > > their website, and then make sure you use these > in your XFree86 config. > > > I went to www.hyundaiq.com and found my > monitor's official sync rates (H > > > 31-60, V 44-75), and promptly wrote them on the > bottom of the base with > > > a Sharpie marker. :-) If your sync rates are > slightly above/below what > > > your monitor is expecting, it won't be able to > auto-adjust to them, and > > > you'll get the weird fuzziness/stripes that you > are seeing. > > > > I don't know how to calculate Modelines, so I had > to google for LCD-Modelines. > > I found the following (now in lts.conf): > > X_MODE_0 = 1024x768 75.00 1024 1048 1184 > 1328 768 771 777 806 > > > > I know, 75 Hz is not the best for LCD, but the > best I could get :) > > So, where and how should I adjust the sync rates > for this Philips Brilliance > > 150P? How did you adjusted them? > > > > TIA, > > Alfred > > > > > > > > > ------------------------------------------------------- > > This SF.NET email is sponsored by: > > SourceForge Enterprise Edition + IBM + LinuxWorld > http://www.vasoftware.com > > > _____________________________________________________________________ > > Ltsp-discuss mailing list. To un-subscribe, or > change prefs, goto: > > > https://lists.sourceforge.net/lists/listinfo/ltsp-discuss > > For additional LTSP help, try #ltsp channel on > irc.freenode.net > > -- > > > ------------------------------------------------------- > This SF.NET email is sponsored by: > SourceForge Enterprise Edition + IBM + LinuxWorld = > Something 2 See! > http://www.vasoftware.com > _____________________________________________________________________ > Ltsp-discuss mailing list. To un-subscribe, or > change prefs, goto: > > https://lists.sourceforge.net/lists/listinfo/ltsp-discuss > For additional LTSP help, try #ltsp channel on irc.freenode.net __________________________________________________ Do you Yahoo!? Yahoo! Mail Plus - Powerful. Affordable. Sign up now. http://mailplus.yahoo.com ------------------------------------------------------- This SF.NET email is sponsored by: SourceForge Enterprise Edition + IBM + LinuxWorld = Something 2 See! http://www.vasoftware.com _____________________________________________________________________ Ltsp-discuss mailing list. To un-subscribe, or change prefs, goto: https://lists.sourceforge.net/lists/listinfo/ltsp-discuss For additional LTSP help, try #ltsp channel on irc.freenode.net --------------End of forwarded message------------------------- -------------------------------------------- Wouter DeBacker ([EMAIL PROTECTED]) 07-Feb-03 00:36:40 (SuSE Linux Xfmail) -------------------------------------------- ------------------------------------------------------- This SF.NET email is sponsored by: SourceForge Enterprise Edition + IBM + LinuxWorld = Something 2 See! http://www.vasoftware.com _____________________________________________________________________ Ltsp-discuss mailing list. To un-subscribe, or change prefs, goto: https://lists.sourceforge.net/lists/listinfo/ltsp-discuss For additional LTSP help, try #ltsp channel on irc.freenode.net ------------------------------------------------------- This SF.NET email is sponsored by: SourceForge Enterprise Edition + IBM + LinuxWorld = Something 2 See! http://www.vasoftware.com _____________________________________________________________________ Ltsp-discuss mailing list. To un-subscribe, or change prefs, goto: https://lists.sourceforge.net/lists/listinfo/ltsp-discuss For additional LTSP help, try #ltsp channel on irc.freenode.net
