Hi Marius, Fixed images for the new BBG were scheduled to be released last night, however my publishing server ran out of hard-drive space, so the images didn't get published overnight rcn-ee.net.
Everything is building/running again, i will ping the MachineKit list when the updated images are available. Regards, On Fri, Jun 17, 2016 at 7:56 PM, Marius Alksnys <[email protected]> wrote: > I am trying to flash eMMC of BeagleBone Green with Machinekit image ... > without success :( > > I tried different images (7.10 and 8.5), different scripts in > /boot/uEnv.txt: > cmdline=init=/opt/scripts/tools/eMMC/init-eMMC-flasher-v3-bbgw.sh > and > cmdline=init=/opt/scripts/tools/eMMC/init-eMMC-flasher-v3-bbgw.sh > > I am using serial debug, where I can see error messages: > http://pastebin.com/6Jdysgip > > I also found similar issue described: > https://groups.google.com/forum/?utm_medium=email&utm_source=footer#!msg/beagleboard/l1GtJPIRvHU/iIP8ab_yBAAJ > > > It boots from sdcard though, but there is /dev/mmcblk0 only and the message > is similar: > ... > [ 0.790742] pinctrl-single 44e10800.pinmux: pin 44e10854 already > requested by 44e10800.pinmux; cannot claim for gpio-leds.8 > [ 0.802412] pinctrl-single 44e10800.pinmux: pin-21 (gpio-leds.8) status > -22 > [ 0.809695] pinctrl-single 44e10800.pinmux: could not request pin 21 on > device pinctrl-single > Loading, please wait... > [ 0.902088] mmc1: unrecognised EXT_CSD revision 7 > [ 0.907071] mmc1: error -22 whilst initialising MMC card > fsck: error 2 (No such file or directory) while executing fsck.ext4 for > /dev/mmcblk0p1 > fsck exited with status code 8 > [ 8.801104] systemd-fsck[144]: rootfs: clean, 80513/217728 files, > 446677/870144 blocks > [ 12.431393] libphy: PHY 4a101000.mdio:01 not found > [ 12.436434] net eth0: phy 4a101000.mdio:01 not found on slave 1 > > Debian GNU/Linux 8 beaglebone ttyO0 > > Machinekit Debian Image 2016-06-05 > > Support/FAQ: http://www.machinekit.io/ > > default username:password is [machinekit:machinekit] > > -- > website: http://www.machinekit.io blog: http://blog.machinekit.io github: > https://github.com/machinekit > --- You received this message because you are subscribed to the Google > Groups "Machinekit" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > Visit this group at https://groups.google.com/group/machinekit. > For more options, visit https://groups.google.com/d/optout. -- Robert Nelson https://rcn-ee.com/ -- website: http://www.machinekit.io blog: http://blog.machinekit.io github: https://github.com/machinekit --- You received this message because you are subscribed to the Google Groups "Machinekit" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. Visit this group at https://groups.google.com/group/machinekit. For more options, visit https://groups.google.com/d/optout.
