Hello all: I have a DE10-nano board and attempting Michael's "mksocfpga_stretch_machinekit_4.9.76-2018-05-26-de10_nano_desktop_sd.img" File. After reboot, I enter in Hwaddr (Hardware Mac address) reboot and get ip address. But I need a TFTP boot file??? Here's my console output.
Any idea's? I am not aware of needing a TFTP file to boot from, Unless
there are different instructions?
I was following "Readme_HDMI_desktop_image.md" in the (Google) Drive
directory.
Please assistance! Thanks!!
-------------------------------------------------------------------
Console output
=> setenv ethaddr 4a:XXXXXXXXXX (entered in real address!)
=> setenv hostname
mksocfpga-nano-soc
=>
saveenv
Saving Environment to
MMC...
Writing to MMC(0)...
done
=>
reset
resetting
...
U-Boot SPL 2018.01-00005-g1cda48acf8 (May 26 2018 -
11:28:03)
drivers/ddr/altera/sequencer.c: Preparing to start memory
calibration
drivers/ddr/altera/sequencer.c: CALIBRATION
PASSED
drivers/ddr/altera/sequencer.c: Calibration
complete
Trying to boot from
MMC1
U-Boot 2018.01-00005-g1cda48acf8 (May 26 2018 - 11:28:03
+0200)
CPU: Altera SoCFPGA
Platform
FPGA: Altera Cyclone V, SE/A6 or SX/C6 or ST/D6, version
0x0
BOOT: SD/MMC Internal Transceiver
(3.0V)
Watchdog
enabled
I2C:
ready
DRAM: 1
GiB
MMC: dwmmc0@ff704000:
0
In:
serial
Out:
serial
Err:
serial
Model: Terasic
DE10-Nano
Net: eth0:
ethernet@ff702000
Hit any key to stop autoboot:
0
switch to partitions #0,
OK
mmc0 is current
device
Scanning mmc
0:3...
fs_devread read outside partition
1903784304
fs_devread read outside partition
1903784304
fs_devread read outside partition
1903784304
fs_devread read outside partition
1903784304
fs_devread read outside partition
1903784304
fs_devread read outside partition
1903784304
fs_devread read outside partition
1903784304
fs_devread read outside partition
1903784304
fs_devread read outside partition
1903784304
fs_devread read outside partition
1903784304
starting
USB...
USB0: Core Release:
2.93a
scanning bus 0 for devices... 4 USB Device(s)
found
scanning usb for storage devices... 0 Storage Device(s)
found
Speed: 1000, full
duplex
BOOTP broadcast
1
DHCP client bound to address 192.168.0.51 (80
ms)
*** Warning: no boot file name; using
'C0A80033.img'
Using ethernet@ff702000
device
TFTP from server 0.0.0.0; our IP address is 192.168.0.51; sending through
gateway
192.168.0.1
Filename
'C0A80033.img'.
Load address:
0x1000000
Loading: T T T T T T T T T
T
Retry count exceeded; starting
again
missing environment variable:
pxeuuid
missing environment variable:
bootfile
Retrieving file:
pxelinux.cfg/01-4a-65-c6-74-51-f2
Speed: 1000, full
duplex
*** ERROR: `serverip' not
set
missing environment variable:
bootfile
Retrieving file:
pxelinux.cfg/C0A80033
Speed: 1000, full
duplex
*** ERROR: `serverip' not
set
missing environment variable:
bootfile
Retrieving file:
pxelinux.cfg/C0A8003
Speed: 1000, full
duplex
*** ERROR: `serverip' not
set
missing environment variable:
bootfile
Retrieving file:
pxelinux.cfg/C0A800
Speed: 1000, full
duplex
*** ERROR: `serverip' not
set
missing environment variable:
bootfile
Retrieving file:
pxelinux.cfg/C0A80
Speed: 1000, full
duplex
*** ERROR: `serverip' not
set
missing environment variable:
bootfile
Retrieving file:
pxelinux.cfg/C0A8
Speed: 1000, full
duplex
*** ERROR: `serverip' not
set
missing environment variable:
bootfile
Retrieving file:
pxelinux.cfg/C0A
Speed: 1000, full
duplex
*** ERROR: `serverip' not
set
missing environment variable:
bootfile
Retrieving file:
pxelinux.cfg/C0
Speed: 1000, full
duplex
*** ERROR: `serverip' not
set
missing environment variable:
bootfile
Retrieving file:
pxelinux.cfg/C
Speed: 1000, full
duplex
*** ERROR: `serverip' not
set
missing environment variable:
bootfile
Retrieving file:
pxelinux.cfg/default-arm-socfpga
Speed: 1000, full
duplex
*** ERROR: `serverip' not
set
missing environment variable:
bootfile
Retrieving file:
pxelinux.cfg/default-arm
Speed: 1000, full
duplex
*** ERROR: `serverip' not
set
missing environment variable:
bootfile
Retrieving file:
pxelinux.cfg/default
Speed: 1000, full
duplex
*** ERROR: `serverip' not
set
Config file not
found
Speed: 1000, full
duplex
BOOTP broadcast
1
DHCP client bound to address 192.168.0.51 (79
ms)
Using ethernet@ff702000
device
TFTP from server 0.0.0.0; our IP address is 192.168.0.51; sending through
gateway
192.168.0.1
Filename
'boot.scr.uimg'.
Load address:
0x2100000
Loading: T T T T T T T T T
T
Retry count exceeded; starting
again
Speed: 1000, full
duplex
BOOTP broadcast
1
DHCP client bound to address 192.168.0.51 (76
ms)
Using ethernet@ff702000
device
TFTP from server 0.0.0.0; our IP address is 192.168.0.51; sending through
gateway
192.168.0.1
Filename
'boot.scr.uimg'.
Load address:
0x1000000
Loading: T T T T T T T T T
T
Retry count exceeded; starting
again
=>
=>
=>
reset
resetting
...
U-Boot SPL 2018.01-00005-g1cda48acf8 (May 26 2018 -
11:28:03)
drivers/ddr/altera/sequencer.c: Preparing to start memory
calibration
drivers/ddr/altera/sequencer.c: CALIBRATION
PASSED
drivers/ddr/altera/sequencer.c: Calibration
complete
Trying to boot from
MMC1
U-Boot 2018.01-00005-g1cda48acf8 (May 26 2018 - 11:28:03 +0200)
--
website: http://www.machinekit.io blog: http://blog.machinekit.io github:
https://github.com/machinekit
---
You received this message because you are subscribed to the Google Groups
"Machinekit" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to [email protected].
Visit this group at https://groups.google.com/group/machinekit.
For more options, visit https://groups.google.com/d/optout.
