Tom,
Sorry I couldn't help out any more than that,
Cheers
Feral Errol
----------
From: Tom Richardson <[EMAIL PROTECTED]>
To: [EMAIL PROTECTED]
Subject: Re: The mystery cam
Date: Friday, September 15, 2000 3:51
I rang Wade today and they don't have any idea where it came from. Their
525B designator is used for a Mazda cam of some sort... will take the
verniers home tonight and get some accurate measurements and work it all
out
from there (hopefully)
Thanks again guys!
- Tom
----- Original Message -----
From: "Craig Overend" <[EMAIL PROTECTED]>
To: <[EMAIL PROTECTED]>
Sent: Friday, September 15, 2000 2:56 AM
Subject: Re: The mystery cam
> We need an accurate measurement of the lobe height and diameter to work
> out lobe lift which is then multiplied by 1.5 to get the approx valve
> lift. You can then look up the cam specs on those web sites and more
> than likely it will have similar performance.
>
> For example the factory B cam that I have is the following:
> 40.3mm - 33.0mm = 7.3mm * 1.5 = 10.95mm valve lift
>
> Craig.
>
> Tom Richardson wrote:
> >
> > Howdy
> >
> > Thanks to Errol and Craig for the replys. The only markings on the cam
> > itself are 'I.5' 'CWC' C1' and 'A3' and on the other side there is '
ER
30'
> > and 'D1' stamped along the shaft at various intervals in between the
lobes,
> > and '525B 110� L.C.' engraved on the end. I dont have anything
accurate
to
> > measure the cam (will borrow some verniers tomorrow and try again) but
all
> > of the lobes are approx 11 mm proud of the shaft. This give any clues?
> > Still got no idea about duration though... argh ;)
> >
> > Thanks again
> >
> > - Tom
> >
> > ----- Original Message -----
> > From: "Errol Smith" <[EMAIL PROTECTED]>
> > To: <[EMAIL PROTECTED]>
> > Sent: Thursday, September 14, 2000 9:03 AM
> > Subject: Re: A bit of help with a cam
> >
> > > Tom,
> > > the duration sounds wrong, could you check it again,
> > > Cheers
> > > Feral Errol
> > >
> > > ----------
> > > From: Tom Richardson <[EMAIL PROTECTED]>
> > > To: [EMAIL PROTECTED]
> > > Subject: A bit of help with a cam
> > > Date: Thursday, September 14, 2000 3:00
> > >
> > > Morning all
> > >
> > > Was wondering if anybody could translate the specs of this cam for
me:
> > >
> > > 525B 110� L.C.
> > >
> > > Duration is 110�? Lift I don't know though.
> > >
> > > What kind of power characteristics would this cam show? Would it be
> > > suitable for an internally stock L18 with minor porting & polishing,
> > > headers and SU's? (Don't laugh cos I don't know if those factors
have
> > > anything to do with the suitability of the cam!). I have it here if
> > there's
> > > a number I missed.
> > >
> > > Thanks!
> > >
> > > - Tom
> > >
> > >
> > >
> >
>
>
--membersozdat-------------------------------------------------------
OZDAT Mailing List Please Note:-
Send (un)subscribe requests to [EMAIL PROTECTED]
Send submissions to [EMAIL PROTECTED]
No unauthorised redistribution of this email
http://www.ozdat.com/ozdatonline/index.htm
http://www.ozdat.com/ozdatonline/listindex.html
http://www.mail-archive.com/[email protected]/
---------------------------------------------------------------------
