errol,
thanks that would be great!!!
andrew
From: "Errol Smith" <[EMAIL PROTECTED]>
To: <[EMAIL PROTECTED]>
Date sent: Thu, 26 Oct 2000 19:14:53 +1000
Send reply to: [EMAIL PROTECTED]
Subject: Re: Thermo wiring
> Andrew,
> I'll get some pricing tomorrow and mail you!
> Cheers
> Feral Errol
>
> ----------
> From: Andrew Greenbury <[EMAIL PROTECTED]>
> To: [EMAIL PROTECTED]
> Subject: Re: Thermo wiring
> Date: Thursday, October 26, 2000 9:27
>
> errol,
> can you give an indication on how much such a water temperature
> controller switch would cost, and any process control companies
> where they would be available in melbourne??
> thanks
> andrew
>
> From: "Errol Smith" <[EMAIL PROTECTED]>
> To: <[EMAIL PROTECTED]>
> Date sent: Wed, 25 Oct 2000 18:30:58 +1000
> Send reply to: [EMAIL PROTECTED]
> Subject: Re: Thermo wiring
>
> > Zac,
> > Using a standard Hella 4RA 30Amp relay and 10amp wire.
> > On the relay there are four terminals (30, 87,85, 86)
> >
> > Terminal 30 goes to battery +ve (through a 15Amp fuse assembly)
> > Terminal 87 goes to the thermo fan +ve wire.
> > The other thermo fan wire goes to a good earth.
> > Terminal 86 also goes to earth
> > Terminal 85 goes to the output terminal of the temp switch.(If two
> terminal
> > model either terminal will do)
> > Temp switch input terminal goes to a switched +ve lead from ignition
> > switch.
> >
> > I use an industrial water temperature controller switch made by LANDIS &
> > GYR (model "T80" with a range from 50 - 110 degrees C). These would be
> > available from most process control companies. These are rated at 10
> times
> > the number of operational cycles of a Davies Craig unit, and have a
> better
> > accuracy when set.
> > This controller uses three terminals with the centre terminal going
> through
> > the fuse to battery positive. Either of the outer terminals is switched
> > power to the fan.
> >
> > If you are going to be adding electrical items to your vehicle such as
> > driving lights stereo etc, think about putting in a separate fuse block
> > with sections for power with ignition on (through a 60 or 90 Amp relay)
> and
> > a second section for constant battery voltage. This will make future
> wiring
> > much easier and neater.
> >
> > Cheers
> > Feral Errol
> >
> >
> >
> >
> >
> >
> >
> > ----------
> > From: Zac Campbell <[EMAIL PROTECTED]>
> > To: [EMAIL PROTECTED]
> > Subject: Thermo wiring
> > Date: Wednesday, October 25, 2000 4:03
> >
> > List, how can I wire my thermo fan using a temp switch and relay? I would
> > like it to just go on and off automatically.
> > Sorry I have absolutely no idea what type of relay to use. I have some 6
> > amp wire here, is that suitable? And what temperature temp switch should
> I
> > get?! Where do I draw power from!!?? argh!
> >
> > Thanks,
> > zac
> >
> >
>
>
>
--membersozdat-------------------------------------------------------
OZDAT Mailing List Please Note:-
Send (un)subscribe requests to [EMAIL PROTECTED]
Send submissions to [EMAIL PROTECTED]
No unauthorised redistribution of this email
http://www.ozdat.com/ozdatonline/index.htm
http://www.ozdat.com/ozdatonline/listindex.html
http://www.mail-archive.com/[email protected]/
---------------------------------------------------------------------
