----------
From:
Mark Alford
Reply To:
[EMAIL PROTECTED]
Sent:
Friday, December 21, 2001 15:32 PM
To:
[EMAIL PROTECTED]
Subject:
Re: 1600
suspention
If you want to go really
fat.
Get four standard lower control
arms (2 for each side) cut them 12.5mm off
centre (2 each way from centre) and then
weld the longer sections together.
Instant 25mm longer control arms. Extra 50mm of track
plus extra camber,
really helps that initial turn in.
If they are cleaned up and
painted, you would never pick them as modified.
CAUTION: Make sure they are
done professionally. I would suggest getting an
engineering shop to do them - you don't
one to break through bad
workmanship. Do this at your own risk.
Mark.
----- Original Message
-----
From:
"Chris Simpson" <[EMAIL PROTECTED]>
To:
<[EMAIL PROTECTED]>
Sent: Friday, December 21, 2001 3:14
PM
Subject: Re:
1600 suspention
>
> Trev,
>
> Before you just go buying some
blindly check them out at the pick-a-part
> near you. THis is what i
understand is the case, i havent measured them
> myself. If you really want to
make your car fat at the front add some R33
> GTS-t vented discs as that adds
another 10mm or so each side!
>
> Chris S
>
>
>
>
Pooley, Trevor writes:
>
>
> Chris,
>
>
> >
Good info mate I didn't know that one. I will have to check to out
at
pick
>
> apart.
>
>
> >
Cheers
> >
Trev
>
>
> >
-----Original Message-----
> > From: Chris Simpson [mailto:[EMAIL PROTECTED]]
> > Sent: Friday, 21 December 2001 12:35
> > To:
[EMAIL PROTECTED]
> > Subject: Re: 1600 suspention
> >
> >
> >
> > Guys,
> >
> > Early 200B Lower
control arms are 8mm longer than the standard 1600
ones.
> > The later ones are the
same. They changed the location of the LCA's on
the
> > later 200B i
believe.
>
>
> >
Chris S
>
>
>
>
>
>
> >
Pooley, Trevor writes:
> >
> >
> >
> > > Guys,
> > >
> > > Re 180B control arms and strut tops. Some
are the same and some are
> > slightly
> > > longer with offset strut
tops and will give a little camber.
> > >
> > > The is something on this on one of the USA
510 websites.
> > >
> > > Cheers
> > > Trev
> > >
> > >
> > > -----Original
Message-----
> > > From: Mark Alford [mailto:[EMAIL PROTECTED]]
> > > Sent: Friday, 21 December 2001 9:06
> > > To:
[EMAIL PROTECTED]
> > > Subject: Re: 1600 suspention
> > >
> > >
> > > 180B arms are
the same length as the 1600 ones I believe.
> > >
> > > Mark.
> > >
> > > ----- Original
Message -----
> > > From: "Shane McManus"
<[EMAIL PROTECTED]>
> > > To:
<[EMAIL PROTECTED]>
> > > Sent: Friday, December
21, 2001 7:45 AM
> > > Subject: 1600 suspention
> > >
> > >
> > > > i have heared that u
can put 180b lower suspention arms into a 1600
for
> > > > increased camber? is
this true
>
> > >
> > >
> > >
> >
> >
> >
> >
>
>
>
>
--membersozdat-------------------------------------------------------
OZDAT Mailing List
Please Note:-
Send (un)subscribe requests to
[EMAIL PROTECTED]
Send submissions to
[EMAIL PROTECTED]
No unauthorised redistribution of this
email
http://www.ozdat.com/ozdatonline/index.htm
http://www.ozdat.com/ozdatonline/listindex.html
http://www.mail-archive.com/[email protected]/
---------------------------------------------------------------------
