Its not that hard, just need to be handy with a welder cos the sheets are thin... took me a bit of time cos it was my first time with a welder. Also they arent perfect so now I have the job of a bit of bog.... Anyway good luck, just think about getting the beast on the road rust free :)
----- Original Message ----- From: "Greg" <[EMAIL PROTECTED]> To: <[EMAIL PROTECTED]> Sent: Sunday, December 23, 2001 9:58 PM Subject: RE: 1600 door sills > Thanks Richard, but I will replace the whole bloody thing. Otherwise the > car is pretty rust free, so I am not in too much trouble. This will be the > only big job I have to perform, oh and the rust around the master cylinder > on the fire wall where fluid has been leaking! > > regards Greg > > -----Original Message----- > From: [EMAIL PROTECTED] > [mailto:[EMAIL PROTECTED]]On Behalf Of Richard Webb > Sent: Sunday, 23 December 2001 1:37 PM > To: [EMAIL PROTECTED] > Subject: Re: 1600 door sills > > > I did this to my 1600, its very time consuming and as greg said its hard > when you come to the front mud flap (which is usually where the rust is!!) > > Anyway good luck and I have a small amount of sill left so if you only need > a small piece let me know and you can have mine if I can find it.... I have > about 1/2 the length from the rear tyre to the front tyre. If that makes any > sense! > > Rich > ----- Original Message ----- > From: "Richardson, Thomas Morgwn - RICTM002" > <[EMAIL PROTECTED]> > To: <[EMAIL PROTECTED]> > Sent: Sunday, December 23, 2001 11:01 AM > Subject: RE: 1600 door sills > > > > Greg, > > > > Randy at the 1600 workshop does them for $88 a side. The problem with > this > > method is that usually the mudwings (the end caps at the front and backs > of the > > sill panels) are buggered too and they're *really* tricky to fix. I > should > > know, my wagon has only one good one! Good luck! > > > > - Tom > > > > -----Original Message----- > > From: Greg [mailto:[EMAIL PROTECTED]] > > Sent: Sunday, 23 December 2001 9:19 AM > > To: [EMAIL PROTECTED] > > Subject: RE: 1600 door sills > > > > > > Thanks to those who replied, > > > > if I can't find anyone in Melbourne, then I will give them a ring, and see > > if they can ship some down to me, depending on what they want for them. > > > > thanks > > > > Greg > > > > -----Original Message----- > > From: [EMAIL PROTECTED] > > [mailto:[EMAIL PROTECTED]]On Behalf Of Jeremy > > Levartovsky > > Sent: Sunday, 23 December 2001 12:27 AM > > To: [EMAIL PROTECTED] > > Subject: RE: 1600 door sills > > > > > > Hi Greg, > > > > I bought mine from Rare Spares in Sydney, I can't remember how much they > > cost, just give 'em a call. > > > > Regards, > > > > Jeremy > > > > -----Original Message----- > > From: [EMAIL PROTECTED] > > [mailto:[EMAIL PROTECTED]]On Behalf Of Greg > > Sent: Saturday, 22 December 2001 3:48 PM > > To: Ozdat mail > > Subject: 1600 door sills > > > > > > I heard somewhere that someone sells bottom sills for 1600's. I think > they > > were in melbourne. Anyone know of this place, and how much they charge??? > > Mine are totally rusted, and I want to chop and replace. > > > > > > regards Greg > > > > > > > > > > --membersozdat------------------------------------------------------- OZDAT Mailing List Please Note:- Send (un)subscribe requests to [EMAIL PROTECTED] Send submissions to [EMAIL PROTECTED] No unauthorised redistribution of this email http://www.ozdat.com/ozdatonline/index.htm http://www.ozdat.com/ozdatonline/listindex.html http://www.mail-archive.com/[email protected]/ ---------------------------------------------------------------------
