Sorry im located in perth, not sure how much freight would be for it to your state, if you want to look into it i dont mind freightin but it would have to be at your expense.
regards chris
From: "Leighton Wolfe" <[EMAIL PROTECTED]>but
Reply-To: [EMAIL PROTECTED]
To: <[EMAIL PROTECTED]>
Subject: Re: lots of parts for sale
Date: Sat, 16 Nov 2002 10:15:20 +1100
where are you fj man ???
i would be interested in the Gearbox and cross member and tail shaft???
thanx
Leighton
----- Original Message -----
From: "FJ MAN" <[EMAIL PROTECTED]>
To: <[EMAIL PROTECTED]>
Sent: Friday, November 15, 2002 9:00 PM
Subject: lots of parts for sale
>
>
> Time to get rid of some less needed partsl
> Intercooler , used for one week (can inspect) custom made core size =
> 550x400x67 tube and fin, overall width 750mm 2.5inch outlets, very good
> quality weldin, made up by rotormotion in perth usin kj thermal core.
lookin
> for around $550.
>
> Z18/20 motor rebuilt, with cam,head work, xf falcon throttle body, ca18det
> injectors, fj20 CAS so it runs just 4 plugs not the original 8, all built
by
> previous owner, very strong motor. custom sump and mounts for slottin
> straight into a 1600. Does not come with turbo only. (offers of a
reasonable
> nature)
>
> Mtx8 microtech to suit z18/20 motor runnin CAS, with or without loom,
comes
> with coil packs and 4 line handset, used on car for a week before ripped
> down for rebuild. Is tuned to run motor with ca18det injectors (dyno
> tunin/maps on computer alone cost 6 hours dyno time.) obviously useless if
> not used on motor but a good buy for a datto owner. lookin for $750 with
> handset and coils.
>
> brand new never used clutch from direct clutches in brisbane ... rated at
> 700hp, 4 puck, sprung centre. cost 700 dollars to suit z18/20 motor, but
it
> should suit fj20 turbo motors too depends on flywheel. its brand new
lookin
> at least 450 for it, (inspection will show its never been used).
>
> Fuel supply set up : surge tank with screw on aircraft fittings, pierburg
> pre pump and vl turbo fuel pump all brand new and cost 700 dollars, lookin
> at around 300 ono for this.
>
> Fj20 turbo gearbox in very good condition, was rebuilt recently before car
> came apart and only used redline oil. can supply crossmember to fit it
into
> a 1600, as well as tail shaft. With tailshaft and crossmember looking at
> offers of around $550 can supply gearbox part numbers etc.
>
> All 1600 datsun parts i can supply, rust free doors, dash's fuel tanks
> gearbox, brakes etc windscreens especially. All must go
> All of this is located in perth, only willin to ship the mtx8 or the fuel
> supply, the rest is probably too much hassle.
> regards chris
>
>
>
>
>
> _________________________________________________________________
> STOP MORE SPAM with the new MSN 8 and get 2 months FREE*
> http://join.msn.com/?page=features/junkmail
>
>
_________________________________________________________________
STOP MORE SPAM with the new MSN 8 and get 2 months FREE* http://join.msn.com/?page=features/junkmail
--membersozdat-------------------------------------------------------
OZDAT Mailing List Please Note:-
Send (un)subscribe requests to [EMAIL PROTECTED]
Send submissions to [EMAIL PROTECTED]
No unauthorised redistribution of this email
http://www.ozdat.com/ozdatonline/index.htm
http://www.ozdat.com/ozdatonline/listindex.html
http://www.mail-archive.com/[email protected]/
---------------------------------------------------------------------
