Link? Max Dillon Charleston SC
Apr 4, 2021 8:49:26 AM Curt Raymond via Mercedes <mercedes@okiebenz.com>: > Have you seen the wildfire lifts like the folks on YouTube are using? Derrick > on Vice Grip Garage has one. They have wheels they can lift up on to move > around. I'm thinking one would go well in the barn on the northern estate. > Curt > > Sent from Yahoo Mail on Android > > On Sat, Apr 3, 2021 at 5:28 PM, Kaleb Striplin via > Mercedes<mercedes@okiebenz.com> wrote: I already have 220 in place. Reason > I asked about installation is I already have this one lift in place, just > need to bolt it done and I have been too lazy to do that. Would probably have > a hard time finding a helper unless the kid gets out of jail, in which case I > would then be on the hook to house him again. > > Sent from my iPhone > >> On Apr 3, 2021, at 3:54 PM, Floyd Thursby via Mercedes >> <mercedes@okiebenz.com> wrote: >> >> I watched some install vids, if you have a helper and something to lift the >> posts with (your tractor) you should be good with putting the posts up. Not >> much to it really. I think you drill the holes for your floor bolts then >> walk the post into place and drive in some expanding bolts then tighten them >> down. You'll need 220 for the motor most likely so if you have 220 in the >> shop you should be good to just run a line over. >> >> --FT >> >>> On 4/3/21 4:37 PM, Kaleb Striplin via Mercedes wrote: >>> I have the drive on alignment lift in the shop that I still have not bolted >>> down. I have been thinking about going ahead with buying a 2 post lift as >>> well and it seems prices have gone up on these since the last time I priced >>> them. I figured I would probably be better off getting one installed rather >>> than trying to do it myself? Anybody had one installed lately and what was >>> the cost? I am getting to the point I really don’t want to work on cars on >>> my back anymore. In fact, I am getting ready to start on lower ball joints >>> on the 211 and I am really thinking about waiting until I have a working >>> lift to do the job. >>> >>> I think the drive on list will be fine for some jobs, but the ramps >>> themselves would get in the way on other jobs which is where the 2 post >>> lift would come into place. Also would be easier to roll dead cars into >>> place with a 2 post lift. >>> >>> Sent from my iPhone >>> >>> _______________________________________ >>> http://www.okiebenz.com >>> >>> To search list archives http://www.okiebenz.com/archive/ >>> >>> To Unsubscribe or change delivery options go to: >>> http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com >>> >> -- >> --FT >> >> _______________________________________ >> http://www.okiebenz.com >> >> To search list archives http://www.okiebenz.com/archive/ >> >> To Unsubscribe or change delivery options go to: >> http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com >> > > > _______________________________________ > http://www.okiebenz.com > > To search list archives http://www.okiebenz.com/archive/ > > To Unsubscribe or change delivery options go to: > http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com > > > _______________________________________ > http://www.okiebenz.com > > To search list archives http://www.okiebenz.com/archive/ > > To Unsubscribe or change delivery options go to: > http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com _______________________________________ http://www.okiebenz.com To search list archives http://www.okiebenz.com/archive/ To Unsubscribe or change delivery options go to: http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com