On Mon, Jun 1, 2015 at 12:22 PM, eien sakebe <[email protected]> wrote: > hello, > i've switched recently from imx.6 sabre sd (everything worked fine) to sabre > auto, built my entier filesystem and npoticed that when the system boots, > the display shows "no signal message". > I've tried passing video=mxcfb0:dev=hdmi,1024x768M@60,if=RGB24 > video=mxcfb1:off video=mxcfb2:off video=mxcfb3:off and when i do the kernel > freezes during boot. > Following is the default log > > CPU: Freescale i.MX6Q rev1.2 at 792 MHz > CPU: Temperature 34 C > Reset cause: POR > Board: MX6Q-Sabreauto revA > I2C: ready > DRAM: 2 GiB > PMIC: PFUZE100 ID=0x10 > Flash: 32 MiB > NAND: 0 MiB > MMC: FSL_SDHC: 0 > auto-detected panel HDMI > Display: HDMI (1024x768) > In: serial > Out: serial > Err: serial > Net: FEC [PRIME] > Hit any key to stop autoboot: 0 > => setenv mmcargs "setenv bootargs console=${console},${baudrate} > video=mxcfb0:dev=hdmi, 1024x768M@60,if=RGB24 bpp=32 root=${mmcroot} > coherent_pool=32M" > => boot > switch to partitions #0, OK > mmc0 is current device > reading boot.scr > ** Unable to read file boot.scr ** > reading zImage > 5934384 bytes read in 277 ms (20.4 MiB/s) > Booting from mmc ... > reading imx6q-sabreauto.dtb > 44656 bytes read in 20 ms (2.1 MiB/s) > Kernel image @ 0x12000000 [ 0x000000 - 0x5a8d30 ] > ## Flattened Device Tree blob at 18000000 > Booting using the fdt blob at 0x18000000 > Using Device Tree in place at 18000000, end 1800de6f > > Starting kernel ... > > Booting Linux on physical CPU 0x0 > Linux version 3.14.28-1.0.0_ga+g91cf351 (ui@ui-virtual-machine) (gcc version > 4.9.2 (GCC) ) #1 SMP PREEMPT Sat May 2 02:00:26 CEST 2015 > CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d > CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache > Machine model: Freescale i.MX6 Quad SABRE Automotive Board > cma: CMA: reserved 320 MiB at 6a000000 > Memory policy: Data cache writealloc > PERCPU: Embedded 8 pages/cpu @ee71d000 s8896 r8192 d15680 u32768 > Built 1 zonelists in Zone order, mobility grouping on. Total pages: 520720 > Kernel command line: console=ttymxc3,115200 video=mxcfb0:dev=hdmi, > 1024x768M@60,if=RGB24 bpp=32 root=/dev/mmcblk2p2 rootwait rw > coherent_pool=32M > PID hash table entries: 4096 (order: 2, 16384 bytes) > Dentry cache hash table entries: 262144 (order: 8, 1048576 bytes) > Inode-cache hash table entries: 131072 (order: 7, 524288 bytes) > Memory: 1736024K/2097152K available (7213K kernel code, 394K rwdata, 6180K > rodata, 328K init, 428K bss, 361128K reserved, 270336K highmem) > Virtual kernel memory layout: > vector : 0xffff0000 - 0xffff1000 ( 4 kB) > fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) > vmalloc : 0xf0000000 - 0xff000000 ( 240 MB) > lowmem : 0x80000000 - 0xef800000 (1784 MB) > pkmap : 0x7fe00000 - 0x80000000 ( 2 MB) > modules : 0x7f000000 - 0x7fe00000 ( 14 MB) > .text : 0x80008000 - 0x80d1c630 (13394 kB) > .init : 0x80d1d000 - 0x80d6f2c0 ( 329 kB) > .data : 0x80d70000 - 0x80dd2a80 ( 395 kB) > .bss : 0x80dd2a8c - 0x80e3dd5c ( 429 kB) > SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 > Preemptible hierarchical RCU implementation. > NR_IRQS:16 nr_irqs:16 16 > L310 cache controller enabled > l2x0: 16 ways, CACHE_ID 0x410000c7, AUX_CTRL 0x32070000, Cache size: 1024 kB > Switching to timer-based delay loop > sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every > 1431655765682ns > Console: colour dummy device 80x30 > Calibrating delay loop (skipped), value calculated using timer frequency.. > 6.00 BogoMIPS (lpj=30000) > pid_max: default: 32768 minimum: 301 > Mount-cache hash table entries: 4096 (order: 2, 16384 bytes) > Mountpoint-cache hash table entries: 4096 (order: 2, 16384 bytes) > CPU: Testing write buffer coherency: ok > CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 > Setting up static identity map for 0x106dd308 - 0x106dd360 > CPU1: Booted secondary processor > CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 > CPU2: Booted secondary processor > CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 > CPU3: Booted secondary processor > CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 > Brought up 4 CPUs > SMP: Total of 4 processors activated. > CPU: All CPU(s) started in SVC mode. > devtmpfs: initialized > VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 > pinctrl core: initialized pinctrl subsystem > regulator-dummy: no parameters > NET: Registered protocol family 16 > DMA: preallocated 32768 KiB pool for atomic coherent allocations > cpuidle: using governor ladder > cpuidle: using governor menu > CPU identified as i.MX6Q, silicon rev 1.2 > Use WDOG1 as reset source > syscon 20c8000.anatop: regmap [mem 0x020c8000-0x020c8fff] registered > vdd1p1: 800 <--> 1375 mV at 1100 mV > vdd3p0: 2800 <--> 3150 mV at 3000 mV > vdd2p5: 2000 <--> 2750 mV at 2400 mV > vddarm: 725 <--> 1450 mV at 1150 mV > vddpu: 725 <--> 1450 mV at 1150 mV > vddsoc: 725 <--> 1450 mV at 1175 mV > syscon 20e0000.iomuxc-gpr: regmap [mem 0x020e0000-0x020e0037] registered > syscon 21bc000.ocotp-ctrl: regmap [mem 0x021bc000-0x021bffff] registered > hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. > hw-breakpoint: maximum watchpoint size is 4 bytes. > imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver > bio: create slab <bio-0> at 0 > mxs-dma 110000.dma-apbh: initialized > cs42888_supply: 3300 mV > 3P3V: 3300 mV > vio1: 3300 mV > vio2: 3300 mV > vd: 3300 mV > va: 5000 mV > platform usb_h1_vbus.30: Driver reg-fixed-voltage requests probe deferral > platform usb_otg_vbus.31: Driver reg-fixed-voltage requests probe deferral > i2c-core: driver [max17135] using legacy suspend method > i2c-core: driver [max17135] using legacy resume method > SCSI subsystem initialized > usbcore: registered new interface driver usbfs > usbcore: registered new interface driver hub > usbcore: registered new device driver usb > usbphy_nop1.12 supply vcc not found, using dummy regulator > usbphy_nop2.13 supply vcc not found, using dummy regulator > i2c i2c-1: IMX I2C adapter registered > i2c i2c-2: IMX I2C adapter registered > Linux video capture interface: v2.00 > pps_core: LinuxPPS API ver. 1 registered > pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti > <[email protected]> > PTP clock support registered > imx-ipuv3 2400000.ipu: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7) > imx-ipuv3 2800000.ipu: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7) > MIPI CSI2 driver module loaded > Advanced Linux Sound Architecture Driver Initialized. > Bluetooth: Core ver 2.18 > NET: Registered protocol family 31 > Bluetooth: HCI device and connection manager initialized > Bluetooth: HCI socket layer initialized > Bluetooth: L2CAP socket layer initialized > Bluetooth: SCO socket layer initialized > cfg80211: Calling CRDA to update world regulatory domain > Switched to clocksource mxc_timer1 > NET: Registered protocol family 2 > TCP established hash table entries: 16384 (order: 4, 65536 bytes) > TCP bind hash table entries: 16384 (order: 5, 131072 bytes) > TCP: Hash tables configured (established 16384 bind 16384) > TCP: reno registered > UDP hash table entries: 1024 (order: 3, 32768 bytes) > UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes) > NET: Registered protocol family 1 > RPC: Registered named UNIX socket transport module. > RPC: Registered udp transport module. > RPC: Registered tcp transport module. > RPC: Registered tcp NFSv4.1 backchannel transport module. > hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available > imx6_busfreq busfreq.16: DDR medium rate not supported. > Bus freq driver module loaded > futex hash table entries: 1024 (order: 4, 65536 bytes) > bounce pool size: 64 pages > VFS: Disk quotas dquot_6.5.2 > Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) > NFS: Registering the id_resolver key type > Key type id_resolver registered > Key type id_legacy registered > jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. > fuse init (API version 7.22) > msgmni has been set to 3502 > io scheduler noop registered > io scheduler deadline registered > io scheduler cfq registered (default) > backlight.17 supply power not found, using dummy regulator > MIPI DSI driver module loaded > mxc_hdmi 20e0000.hdmi_video: Detected HDMI controller 0x13:0xa:0xa0:0xc1 > mxc_sdc_fb fb.23: registered mxc display driver hdmi > Console: switching to colour frame buffer device 80x30 > mxc_hdmi 20e0000.hdmi_video: Error only one HDMI output support now! > mxc_sdc_fb fb.24: NO mxc display driver found! > mxc_sdc_fb fb.25: NO mxc display driver found! > mxc_sdc_fb fb.26: registered mxc display driver ldb > mxc_hdmi 20e0000.hdmi_video: Read EDID again > imx-sdma 20ec000.sdma: no iram assigned, using external mem > imx-sdma 20ec000.sdma: no event needs to be remapped > imx-sdma 20ec000.sdma: loaded firmware 3.1 > imx-sdma 20ec000.sdma: initialized > pfuze100-regulator 1-0008: Full layer: 1, Metal layer: 2 > pfuze100-regulator 1-0008: FAB: 0, FIN: 0 > pfuze100-regulator 1-0008: pfuze100 found. > SW1AB: 300 <--> 1875 mV at 1375 mV > SW1C: 300 <--> 1875 mV at 1375 mV > SW2: 800 <--> 3300 mV at 3000 mV > SW3A: 400 <--> 1975 mV at 1500 mV > SW3B: 400 <--> 1975 mV at 1500 mV > SW4: 800 <--> 1975 mV at 1800 mV > SWBST: 5000 <--> 5150 mV at 5000 mV > VSNVS: 1000 <--> 3000 mV at 3000 mV > VREFDDR: 750 mV > VGEN1: 800 <--> 1550 mV at 800 mV > VGEN2: 800 <--> 1550 mV at 1500 mV > VGEN3: 1800 <--> 3300 mV at 1800 mV > VGEN4: 1800 <--> 3300 mV at 1800 mV > VGEN5: 1800 <--> 3300 mV at 2500 mV > VGEN6: 1800 <--> 3300 mV at 2800 mV > Serial: IMX driver > 21ec000.serial: ttymxc2 at MMIO 0x21ec000 (irq = 60, base_baud = 5000000) is > a IMX > 21f0000.serial: ttymxc3 at MMIO 0x21f0000 (irq = 61, base_baud = 5000000) is > a IMX > mxc_hdmi 20e0000.hdmi_video: create default modelist > > Anyone have a begining of idea please ?
Maybe https://bugzilla.yoctoproject.org/show_bug.cgi?id=6703 ? Daiane > > thank you in advance > > -- > _______________________________________________ > meta-freescale mailing list > [email protected] > https://lists.yoctoproject.org/listinfo/meta-freescale > -- _______________________________________________ meta-freescale mailing list [email protected] https://lists.yoctoproject.org/listinfo/meta-freescale
