All your numeric variables are being reset during the @TPINDX (tool plane index) section. In this instance SmartCAM is treating the @TPINDX section the same as @TOOLCHG.
Change SMF question #60 to 0. This will eliminate the resetting of #FEED and other variable during @TPINDX. Unfortunately this will also eliminate the resetting of numeric variables at a tool change. You may need to add #RESET() to the @TOOLCHG section for any critical variables that are not unconditionally output during a tool change. i.e. @TOOLCHG #MOV <#FXD> Z#V9 M09 #OFFBLK #EVAL(#StepDesc=jos(st_desc)) (#StepDesc) #ONBLK M98 P9000 M01 T#TOOL M06 B#U0 G00 #WKPLN X#XPOS Y#YPOS T#NTOOL S#SPEED #SPNDL G43 Z#V8 H#LOFF M08 < #MOV>< X#XPOS>< Y#YPOS> #RESET(#ZDPTH,#ZCHK,#PECK,#FEED) ============================================= Fred Lauzus, CAM Programming Coordinator High Steel Structures, Incorporated mailto:[EMAIL PROTECTED] http://www.highsteel.com ============================================= -----Original Message----- From: Colin Williams [mailto:[EMAIL PROTECTED]] Sent: Tuesday, April 25, 2000 2:43 PM To: Lauzus, Frederick; Smartcam Forum Subject: Re: [mfg-smartcam] CANNED CYCLE Here is my tmp Colin -----Original Message----- From: Lauzus, Frederick <[EMAIL PROTECTED]> To: Colin Williams <[EMAIL PROTECTED]>; Smartcam Forum <[EMAIL PROTECTED]> Date: Tuesday, April 25, 2000 8:45 AM Subject: RE: [mfg-smartcam] CANNED CYCLE >Check if there is a #RESET() command that resets the variable #FEED, >possibly in the @TPINDX section. > >============================================= > Fred Lauzus, CAM Programming Coordinator > High Steel Structures, Incorporated > mailto:[EMAIL PROTECTED] http://www.highsteel.com >============================================= > > >-----Original Message----- >From: Colin Williams [mailto:[EMAIL PROTECTED]] >Sent: Tuesday, April 25, 2000 8:20 AM >To: Smartcam Forum >Subject: [mfg-smartcam] CANNED CYCLE > > >This is what my statement looks like. It is still calling up the feedrate. > >@FXD1 >< #ABSI>< #FXD>< #RTNLVL>< X#XPOS>< Y#YPOS>< Z#ZDPTH R#ZCHK>< F#FEED> > > >Colin > > >-----Original Message----- >From: Chinh N Pham <[EMAIL PROTECTED]> >To: 'Colin Williams' <[EMAIL PROTECTED]> >Date: Monday, April 24, 2000 4:29 PM >Subject: RE: [mfg-smartcam] canned cycle > > >> >>In the code gen. statement, put the feed rate call out in brackets <>, then >>it won't output same FEED value unless it is different. >><F#FEED> >> >>Chinh >>> -----Original Message----- >>> From: [EMAIL PROTECTED] >>> [mailto:[EMAIL PROTECTED]]On Behalf Of Colin Williams >>> Sent: Monday, April 24, 2000 3:38 PM >>> To: Smartcam Forum >>> Subject: [mfg-smartcam] canned cycle >>> >>> >>> pmill v11.0: >>> >>> When using canned cycles on different faces you would >>> normally cancel (g80) >>> then go onto the next face. Every time you call up the same >>> canned cycle for >>> different faces the feedrate is also called up. Is there a >>> way just to call >>> up the feedrate just at the first canned cycle? This way the >>> operator just >>> has to change the first feedrate. >>> >>> Thank You >>> >>> Colin Williams >>> Wabtec Corporation > > > >Thank You > >Colin Williams >Wabtec Corporation > > > >====================================================================== >To find out more about this mailing list including how to unsubscribe, >send the message "info mfg-smartcam" to [EMAIL PROTECTED] >====================================================================== ====================================================================== To find out more about this mailing list including how to unsubscribe, send the message "info mfg-smartcam" to [EMAIL PROTECTED] ======================================================================
