MessageI've heard bad things about them (the "new" ones, not rebuilds).  I also 
heard they were cast/assembled here in the states (Florida?).
  ----- Original Message ----- 
  From: Skip Cannon 
  To: [email protected] ; [email protected] 
  Sent: Saturday, March 28, 2009 10:23 PM
  Subject: RE: OK, fine, let's talk v8s


  I've had two Miata crate motors, both new, not the remans they sell now.  
Both were bad but I found the problems before I started them.  One had to have 
a new crank, cams and bearings,  The crank had metal snags sticking up from two 
of the main journals which had gouged grooves in the main bearings.  You could 
see that the engine had only been rotated about 2/3 of a turn during assembly.  
The crank was also flattened around the oil holes indicating that there had 
been work done on it.  The cams were rusty with pits on the lobes.
   
  The other one had rust on the cylinder walls.  
   
  I talked with someone deep inside the Mazda parts system and he told me that 
the crate engines were assembled from reject parts from the engine assembly 
plant.
   
  Skip
    -----Original Message-----
    From: [email protected] 
[mailto:[email protected]] On Behalf Of Bill Cardell
    Sent: Saturday, March 28, 2009 8:04 PM
    To: [email protected]; [email protected]
    Subject: RE: OK, fine, let's talk v8s


    Not so sure it's true of the Miata crate motors. I spoke with someone at 
Laguna this weekend who sold her car after three or four crate motors failed, 
none lasting more than a year. This is in a street car.

    Bill Cardell 
    TurboDog's Dad 
    www.flyinmiata.com 
    www.fmwestfield.com 
    orders 1-800-FLY-MX5S 
    Before you call our tech line (970.464.5600) please check out the FAQ 
section of our website 







----------------------------------------------------------------------------
    From: [email protected] 
[mailto:[email protected]] On Behalf Of [email protected]
    Sent: Saturday, March 28, 2009 7:28 PM
    To: [email protected]
    Subject: Re: OK, fine, let's talk v8s


    In a message dated 3/28/2009 8:16:52 P.M. Eastern Standard Time, 
[email protected] writes:
      On the crate motor:

      I met a guy (Keith Turk, some of you may know him) who runs at
      Bonneville.  He ran very expensive small blocks in a 1980 Camaro.  You
      may have seen the car in Hot Rod Mag as that is one of his sponsors.
      He gets surplus parts from NASCAR teams, things like radiators, etc.
      He had some small blocks with well over $20k invested.
      A while back a friend of his and fellow Bonneville guy passed away.
      He wanted to run the next year but didn't get to invest the time into
      prep like he had in previous years.  So, he decided to just get a big
      block crate motor so he could run 200+MPH without having to spend the
      time and money in very high dollar small block motors.  He spent a
      fraction of what he usually spent on motors.  Well, with that crate
      motor he ran the fastest he had ever run.
      There is a lot to be said for those crate motors.

    I don't doubt it.  When the Speed Channel or Spike motorheads are dynoing 
stock and crate engines, the crate performance engines put out incredible HP.  
The crate engines should be better engineered, as the parts have been produced 
by the folks who also produce the stock engines, and they have "standards" to 
meet/uphold.  


----------------------------------------------------------------------------
    A Good Credit Score is 700 or Above. See yours in just 2 easy steps! 


------------------------------------------------------------------------------


  _______________________________________________
  Miatapower mailing list
  [email protected]
  http://list.miatapower.net/cgi-bin/mailman/listinfo/miatapower

_______________________________________________
Miatapower mailing list
[email protected]
http://list.miatapower.net/cgi-bin/mailman/listinfo/miatapower

Reply via email to