You can normally get a dedicated iLO port for HP machines that lack them as an option, this is apparently 514206-B21 on your machine.
There is perhaps a register to poke in bge that will make bge0 useable regardless of what the bios does as well. See if you can set it as a dedicated NIC via the bios, we don't do 'shared' management ports in OpenBSD. On Tue, May 10, 2011 at 07:54:25AM +0000, Peter van Oord van der Vlies wrote: > Hello misc, > > I am installing several HP DL320G6 servers and see there are some problems > with the Network Adapter that is shared with ILO2 . > > When openbsd boots the ILO adapter becomes unavailable and within openbsd the > interface bge0 is not usable. It's connected at 10BaseT but in real it's > connected at 1000baseT . > Ifconfig : > > bge0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500 > lladdr 1c:c1:de:f9:c6:50 > priority: 0 > media: Ethernet autoselect (10baseT full-duplex) > status: active > > See below dmesg output : > > OpenBSD 4.9 (GENERIC.MP) #794: Wed Mar 2 07:19:02 MST 2011 > [email protected]:/usr/src/sys/arch/i386/compile/GENERIC.MP > cpu0: Intel(R) Xeon(R) CPU E5502 @ 1.87GHz ("GenuineIntel" 686-class) 1.87 > GHz > cpu0: > FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUS > H,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3 > ,CX16,xTPR,PDCM,DCA,SSE4.1,SSE4.2,POPCNT > real mem = 3747340288 (3573MB) > avail mem = 3675897856 (3505MB) > mainbus0 at root > bios0 at mainbus0: AT/286+ BIOS, date 12/31/99, BIOS32 rev. 0 @ 0xf0000, > SMBIOS rev. 2.7 @ 0xdf7fe000 (134 entries) > bios0: vendor HP version "W07" date 01/29/2011 > bios0: HP ProLiant DL320 G6 > acpi0 at bios0: rev 2 > acpi0: sleep states S0 S4 S5 > acpi0: tables DSDT FACP SPCR MCFG HPET FFFF SPMI ERST APIC SRAT FFFF BERT HEST > DMAR SSDT SSDT SSDT > acpi0: wakeup devices PCI0(S4) > acpitimer0 at acpi0: 3579545 Hz, 24 bits > acpimcfg0 at acpi0 addr 0xe0000000, bus 0-63 > acpihpet0 at acpi0: 14318179 Hz > acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat > cpu0 at mainbus0: apid 16 (boot processor) > cpu0: apic clock running at 133MHz > cpu1 at mainbus0: apid 20 (application processor) > cpu1: Intel(R) Xeon(R) CPU E5502 @ 1.87GHz ("GenuineIntel" 686-class) 1.87 > GHz > cpu1: > FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUS > H,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3 > ,CX16,xTPR,PDCM,DCA,SSE4.1,SSE4.2,POPCNT > ioapic0 at mainbus0: apid 8 pa 0xfec00000, version 20, 24 pins > ioapic1 at mainbus0: apid 0 pa 0xfec80000, version 20, 24 pins > acpiprt0 at acpi0: bus 1 (IP2P) > acpiprt1 at acpi0: bus 3 (NIB1) > acpiprt2 at acpi0: bus 4 (IPT5) > acpiprt3 at acpi0: bus -1 (PRB2) > acpiprt4 at acpi0: bus 10 (PT07) > acpiprt5 at acpi0: bus 7 (PT03) > acpiprt6 at acpi0: bus 13 (PT01) > acpiprt7 at acpi0: bus 0 (PCI0) > acpicpu0 at acpi0: C3, C3, C1 > acpicpu1 at acpi0: C3, C3, C1 > acpitz0 at acpi0: critical temperature 31 degC > bios0: ROM list: 0xc0000/0xb000 0xcb000/0x4000! 0xcf000/0x1a00 > ipmi at mainbus0 not configured > pci0 at mainbus0 bus 0: configuration mode 1 (bios) > pchb0 at pci0 dev 0 function 0 "Intel 5500 Host" rev 0x13 > ppb0 at pci0 dev 1 function 0 "Intel X58 PCIE" rev 0x13 > pci1 at ppb0 bus 13 > bnx0 at pci1 dev 0 function 0 "Broadcom BCM5709" rev 0x20: apic 0 int 4 (irq > 7) > bnx1 at pci1 dev 0 function 1 "Broadcom BCM5709" rev 0x20: apic 0 int 16 (irq > 11) > ppb1 at pci0 dev 3 function 0 "Intel X58 PCIE" rev 0x13 > pci2 at ppb1 bus 7 > ppb2 at pci0 dev 7 function 0 "Intel X58 PCIE" rev 0x13 > pci3 at ppb2 bus 10 > ciss0 at pci3 dev 0 function 0 "Hewlett-Packard Smart Array" rev 0x01: apic 0 > int 6 (irq 7) > ciss0: 1 LD, HW rev 2, FW 3.00/3.00, 64bit fifo rro > scsibus0 at ciss0: 1 targets > sd0 at scsibus0 targ 0 lun 0: <HP, LOGICAL VOLUME, 3.00> SCSI3 0/direct fixed > sd0: 286070MB, 512 bytes/sec, 585871964 sec total > pchb1 at pci0 dev 13 function 0 vendor "Intel", unknown product 0x343a rev > 0x13 > pchb2 at pci0 dev 13 function 1 vendor "Intel", unknown product 0x343b rev > 0x13 > pchb3 at pci0 dev 13 function 2 vendor "Intel", unknown product 0x343c rev > 0x13 > pchb4 at pci0 dev 13 function 3 vendor "Intel", unknown product 0x343d rev > 0x13 > pchb5 at pci0 dev 13 function 4 "Intel 5520/X58 QuickPath" rev 0x13 > pchb6 at pci0 dev 13 function 5 "Intel 5520 QuickPath" rev 0x13 > pchb7 at pci0 dev 13 function 6 vendor "Intel", unknown product 0x341a rev > 0x13 > pchb8 at pci0 dev 14 function 0 vendor "Intel", unknown product 0x341c rev > 0x13 > pchb9 at pci0 dev 14 function 1 vendor "Intel", unknown product 0x341d rev > 0x13 > pchb10 at pci0 dev 14 function 2 vendor "Intel", unknown product 0x341e rev > 0x13 > pchb11 at pci0 dev 14 function 3 vendor "Intel", unknown product 0x341f rev > 0x13 > pchb12 at pci0 dev 14 function 4 vendor "Intel", unknown product 0x3439 rev > 0x13 > "Intel X58 Misc" rev 0x13 at pci0 dev 20 function 0 not configured > "Intel X58 GPIO" rev 0x13 at pci0 dev 20 function 1 not configured > "Intel X58 RAS" rev 0x13 at pci0 dev 20 function 2 not configured > uhci0 at pci0 dev 26 function 0 "Intel 82801JI USB" rev 0x00: apic 8 int 20 > (irq 5) > uhci1 at pci0 dev 26 function 1 "Intel 82801JI USB" rev 0x00: apic 8 int 23 > (irq 7) > uhci2 at pci0 dev 26 function 2 "Intel 82801JI USB" rev 0x00: apic 8 int 22 > (irq 10) > ehci0 at pci0 dev 26 function 7 "Intel 82801JI USB" rev 0x00: apic 8 int 22 > (irq 10) > usb0 at ehci0: USB revision 2.0 > uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1 > ppb3 at pci0 dev 28 function 0 "Intel 82801JI PCIE" rev 0x00 > pci4 at ppb3 bus 2 > ppb4 at pci4 dev 0 function 0 "ServerWorks PCIE-PCIX" rev 0xb5 > pci5 at ppb4 bus 3 > bge0 at pci5 dev 4 function 0 "Broadcom BCM5715" rev 0xa3, BCM5715 A3 > (0x9003): apic 8 int 16 (irq 7), address 1c:c1:de:f9:c6:50 > brgphy0 at bge0 phy 1: BCM5714 10/100/1000baseT/SX PHY, rev. 0 > bge1 at pci5 dev 4 function 1 "Broadcom BCM5715" rev 0xa3, BCM5715 A3 > (0x9003): apic 8 int 17 (irq 11), address 1c:c1:de:f9:c6:51 > brgphy1 at bge1 phy 1: BCM5714 10/100/1000baseT/SX PHY, rev. 0 > ppb5 at pci0 dev 28 function 4 "Intel 82801JI PCIE" rev 0x00 > pci6 at ppb5 bus 4 > uhci3 at pci0 dev 29 function 0 "Intel 82801JI USB" rev 0x00: apic 8 int 20 > (irq 5) > uhci4 at pci0 dev 29 function 1 "Intel 82801JI USB" rev 0x00: apic 8 int 23 > (irq 7) > uhci5 at pci0 dev 29 function 2 "Intel 82801JI USB" rev 0x00: apic 8 int 22 > (irq 10) > ehci1 at pci0 dev 29 function 7 "Intel 82801JI USB" rev 0x00: apic 8 int 20 > (irq 5) > usb1 at ehci1: USB revision 2.0 > uhub1 at usb1 "Intel EHCI root hub" rev 2.00/1.00 addr 1 > ppb6 at pci0 dev 30 function 0 "Intel 82801BA Hub-to-PCI" rev 0x90 > pci7 at ppb6 bus 1 > vga1 at pci7 dev 3 function 0 "ATI ES1000" rev 0x02 > wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation) > wsdisplay0: screen 1-5 added (80x25, vt100 emulation) > radeondrm0 at vga1: apic 8 int 23 (irq 7) > drm0 at radeondrm0 > "Compaq iLO" rev 0x03 at pci7 dev 4 function 0 not configured > "Compaq iLO" rev 0x03 at pci7 dev 4 function 2 not configured > uhci6 at pci7 dev 4 function 4 "Hewlett-Packard USB" rev 0x00: apic 8 int 22 > (irq 10) > "Hewlett-Packard IPMI" rev 0x00 at pci7 dev 4 function 6 not configured > usb2 at uhci6: USB revision 1.0 > uhub2 at usb2 "Hewlett-Packard UHCI root hub" rev 1.00/1.00 addr 1 > pcib0 at pci0 dev 31 function 0 "Intel 82801JIR LPC" rev 0x00 > pciide0 at pci0 dev 31 function 2 "Intel 82801JI SATA" rev 0x00: DMA, channel > 0 configured to native-PCI, channel 1 configured to native-PCI > pciide0: using apic 8 int 17 (irq 11) for native-PCI interrupt > pciide1 at pci0 dev 31 function 5 "Intel 82801JI SATA" rev 0x00: DMA, channel > 0 wired to native-PCI, channel 1 wired to native-PCI > pciide1: using apic 8 int 17 (irq 11) for native-PCI interrupt > usb3 at uhci0: USB revision 1.0 > uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1 > usb4 at uhci1: USB revision 1.0 > uhub4 at usb4 "Intel UHCI root hub" rev 1.00/1.00 addr 1 > usb5 at uhci2: USB revision 1.0 > uhub5 at usb5 "Intel UHCI root hub" rev 1.00/1.00 addr 1 > usb6 at uhci3: USB revision 1.0 > uhub6 at usb6 "Intel UHCI root hub" rev 1.00/1.00 addr 1 > usb7 at uhci4: USB revision 1.0 > uhub7 at usb7 "Intel UHCI root hub" rev 1.00/1.00 addr 1 > usb8 at uhci5: USB revision 1.0 > uhub8 at usb8 "Intel UHCI root hub" rev 1.00/1.00 addr 1 > isa0 at pcib0 > isadma0 at isa0 > com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo > com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo > com1: probed fifo depth: 0 bytes > pckbc0 at isa0 port 0x60/5 > pckbd0 at pckbc0 (kbd slot) > pckbc0: using irq 1 for kbd slot > wskbd0 at pckbd0: console keyboard, using wsdisplay0 > pcppi0 at isa0 port 0x61 > spkr0 at pcppi0 > npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16 > mtrr: Pentium Pro MTRR support > uhidev0 at uhub2 port 1 configuration 1 interface 0 "HP Virtual Keyboard" rev > 1.10/0.02 addr 2 > uhidev0: iclass 3/1 > ukbd0 at uhidev0: 8 modifier keys, 6 key codes, country code 33 > wskbd1 at ukbd0 mux 1 > wskbd1: connecting to wsdisplay0 > uhidev1 at uhub2 port 1 configuration 1 interface 1 "HP Virtual Keyboard" rev > 1.10/0.02 addr 2 > uhidev1: iclass 3/1 > ums0 at uhidev1: 3 buttons > wsmouse0 at ums0 mux 0 > vscsi0 at root > scsibus1 at vscsi0: 256 targets > softraid0 at root > root on sd0a swap on sd0b dump on sd0b > bnx0: address 1c:c1:de:7a:ef:1c > brgphy2 at bnx0 phy 1: BCM5709 10/100/1000baseT PHY, rev. 8 > bnx1: address 1c:c1:de:7a:ef:1e > brgphy3 at bnx1 phy 1: BCM5709 10/100/1000baseT PHY, rev. 8 > > > Thanks, > > Peter
