* Stuart Henderson <[email protected]> le [20-06-2014 00:19:17 +0000]:
> On 2014-06-18, Thuban <[email protected]> wrote:
> > * Peter N. M. Hansteen <[email protected]> le [18-06-2014 18:37:52 +0200]:
> >> On Wed, Jun 18, 2014 at 06:21:24PM +0200, Thuban wrote:
> >> > > >
> >> > > > jme0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
> >> > > > lladdr 00:90:f5:bc:7b:5E
> >> > > > groups egress
> >> > > > media: Ethernet autoselect (none)
> >> > > > status: no carrier
> >> > > > inet6 fe80::290:f5ff:febc:7b56%jme0 prefixlen 64 scopeid 0x1
> >> > > > inet 192.168.1.70 netmask 0xffffff0 broadcast 192.168.1.255
> >> > > >
> >>
> >> > Haha.
> >> > Cable is plugged.
> >> >
> >> > I tried today to modify media to 10baseT, but the router's LED is still
> >> > off and I can't connect.
> >>
> >> Try a different cable.
> >>
> >> If you get status: no carrier with a cable plugged in, the most likely
> >> culprit is
> >> the cable.
> >
> > I am currently using this cable on my debian and connexion works
> >>
> >> Are you saying here that the exact same hardware works with linux, but gets
> >> a 'no carrier' with OpenBSD and FreeBSD? Is it possible to try booting with
> >> Linux again (a live cd will do) and check link status?
> >>
> > Exactly. On linux, I can use the ethernet correctly. The linux's
> > ifconfig gives this :
> >
> > eth0 Link encap:Ethernet HWaddr 00:90:f5:bc:7b:56
> > inet adr:192.168.1.68 Bcast:192.168.1.255 Masque:255.255.255.0
> > adr inet6: 2001:41d0:fe34:de00:290:f5ff:febc:7b56/64
> > Scope:Global
> > adr inet6: fe80::290:f5ff:febc:7b56/64 Scope:Lien
> > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
> > RX packets:266 errors:0 dropped:0 overruns:0 frame:0
> > TX packets:263 errors:0 dropped:0 overruns:0 carrier:0
> > collisions:0 lg file transmission:1000
> > RX bytes:61935 (60.4 KiB) TX bytes:31036 (30.3 KiB)
> > Interruption:44
> >
> > Regards
>
> Given what vigdis said, I wonder:-
>
> - what speed is the switch port you're using
>
> - what speed does linux negotiate
>
> - what speed is your NIC supposed to support? 10/100 or also gigabit?
>
I'm not sure how to give you the correct answers to theses questions.
The speed is 100Mb/s. Following, the output of ethtool on the linux box
:
Settings for eth0:
Supported ports: [ TP MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Supported pause frame use: No
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Link partner advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Link partner advertised pause frame use: Symmetric
Link partner advertised auto-negotiation: Yes
Speed: 100Mb/s
Duplex: Full
Port: MII
PHYAD: 1
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: pg
Wake-on: g
Current message level: 0x000020c6 (8390)
probe link rx_err tx_err hw
Link detected: yes
Do not hesitate to give me some advice to find more interesting
informations.
Regards,
--
Thuban
PubKey : http://yeuxdelibad.net/Divers/thuban.pub
