* Gustav Fransson Nyvell <[email protected]> le [20-06-2014 11:32:22 +0200]:
> On 06/20/14 07:45, Thuban wrote:
> >* Stuart Henderson <[email protected]> le [20-06-2014 00:19:17 +0000]:
> >>On 2014-06-18, Thuban <[email protected]> wrote:
> >>>* Peter N. M. Hansteen <[email protected]> le [18-06-2014 18:37:52 +0200]:
> >>>>On Wed, Jun 18, 2014 at 06:21:24PM +0200, Thuban wrote:
> >>>>>>> jme0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
> >>>>>>> lladdr 00:90:f5:bc:7b:5E
> >>>>>>> groups egress
> >>>>>>> media: Ethernet autoselect (none)
> >>>>>>> status: no carrier
> >>>>>>> inet6 fe80::290:f5ff:febc:7b56%jme0 prefixlen 64 scopeid 0x1
> >>>>>>> inet 192.168.1.70 netmask 0xffffff0 broadcast 192.168.1.255
> >>>>>>>
> >>>>>Haha.
> >>>>>Cable is plugged.
> >>>>>
> >>>>>I tried today to modify media to 10baseT, but the router's LED is still
> >>>>>off and I can't connect.
> >>>>Try a different cable.
> >>>>
> >>>>If you get status: no carrier with a cable plugged in, the most likely
> >>>>culprit is
> >>>>the cable.
> >>>I am currently using this cable on my debian and connexion works
> >>>>Are you saying here that the exact same hardware works with linux, but
> >>>>gets
> >>>>a 'no carrier' with OpenBSD and FreeBSD? Is it possible to try booting
> >>>>with
> >>>>Linux again (a live cd will do) and check link status?
> >>>>
> >>>Exactly. On linux, I can use the ethernet correctly. The linux's
> >>>ifconfig gives this :
> >>>
> >>> eth0 Link encap:Ethernet HWaddr 00:90:f5:bc:7b:56
> >>> inet adr:192.168.1.68 Bcast:192.168.1.255
> >>> Masque:255.255.255.0
> >>> adr inet6: 2001:41d0:fe34:de00:290:f5ff:febc:7b56/64
> >>> Scope:Global
> >>> adr inet6: fe80::290:f5ff:febc:7b56/64 Scope:Lien
> >>> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
> >>> RX packets:266 errors:0 dropped:0 overruns:0 frame:0
> >>> TX packets:263 errors:0 dropped:0 overruns:0 carrier:0
> >>> collisions:0 lg file transmission:1000
> >>> RX bytes:61935 (60.4 KiB) TX bytes:31036 (30.3 KiB)
> >>> Interruption:44
> >>>
> >>>Regards
> >>Given what vigdis said, I wonder:-
> >>
> >>- what speed is the switch port you're using
> >>
> >>- what speed does linux negotiate
> >>
> >>- what speed is your NIC supposed to support? 10/100 or also gigabit?
> >>
> >I'm not sure how to give you the correct answers to theses questions.
> >The speed is 100Mb/s. Following, the output of ethtool on the linux box
> >:
> >
> >
> > Settings for eth0:
> > Supported ports: [ TP MII ]
> > Supported link modes: 10baseT/Half 10baseT/Full
> > 100baseT/Half 100baseT/Full
> > 1000baseT/Half 1000baseT/Full
> > Supported pause frame use: No
> > Supports auto-negotiation: Yes
> > Advertised link modes: 10baseT/Half 10baseT/Full
> > 100baseT/Half 100baseT/Full
> > 1000baseT/Half 1000baseT/Full
> > Advertised pause frame use: No
> > Advertised auto-negotiation: Yes
> > Link partner advertised link modes: 10baseT/Half 10baseT/Full
> > 100baseT/Half 100baseT/Full
> > Link partner advertised pause frame use: Symmetric
> > Link partner advertised auto-negotiation: Yes
> > Speed: 100Mb/s
> > Duplex: Full
> > Port: MII
> > PHYAD: 1
> > Transceiver: internal
> > Auto-negotiation: on
> > Supports Wake-on: pg
> > Wake-on: g
> > Current message level: 0x000020c6 (8390)
> > probe link rx_err tx_err hw
> > Link detected: yes
> >
> >Do not hesitate to give me some advice to find more interesting
> >informations.
> >
> >Regards,
> >
> Hi,
>
> What speed is your switch?
>
> Can you give us the switch make and model and the NIC make and model?
>
The switch is on the router given by my internet access provider. The
router is a Thomson Gateway TG784n. Speed is at 100 Mb/s.
I'm not sure to understand correctly
what you need because of my poor english. :(
About the NIC :
Ethernet controller: JMicron Technology Corp. JMC250
PCI Express Gigabit Ethernet Controller (rev 05)
Subsystem: CLEVO/KAPOK Computer Device 4140
Regards,
--
Thuban
PubKey : http://yeuxdelibad.net/Divers/thuban.pub
