On 2016-08-03 23:33, YASUOKA Masahiko wrote:
On Tue, 24 May 2016 16:02:21 -0400
Steve Shockley <[email protected]> wrote:
I have an HP BL460c blade I'm using with OpenBSD. I was able to get
5.8 to install by disabling ACPI; since I'm lazy I didn't submit a bug
report. I tried to upgrade to 5.9 (and -current), but booting from
I hit a similar problem on NEC Express5800/R110h-1. On that machine,
X2APIC is enabled on boot and this seems to cause the panic following.
cpu0 at mainbus0panic: cpu at apic id 0 already attached?
So the diff disables the X2APIC. Can you try the diff attached?
Thanks for your help. Unfortunately, this did not solve the issue. I
was able to install by disabling ACPI, but the result would not boot.
Booting bsd.mp results in this result. Unfortunately at this point
moving the mouse or typing only generates garbage.
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0panic: cpu at apic id 0 already attached?
Stopped at Debugger+0x9: leave
TID PID UID PRFLAGS PFLAGS CPU COMMAND
* 0 0 0 0x10000 0x200 0 swapper
Debugger() at Debugger+0x9
panic() at panic+0xfe
cpu_attach() at cpu_attach+0x381
config_attach() at config_attach+0x1bc
acpimadt_attach() at acpimadt_attach+0x5cd
config_attach() at config_attach+0x1bc
acpi_attach() at acpi_attach+0x497
config_attach() at config_attach+0x1bc
bios_attach() at bios_attach+0x236
config_attach() at config_attach+0x1bc
mainbus_attach() at mainbus_attach+0x74
config_attach() at config_attach+0x1bc
cpu_configure() at cpu_configure+0x1b
main() at main+0x40d
end trace frame: 0x0, count: 1
http://www.openbsd.org/ddb.html describes the minimum info required in
bug
reports. Insufficient info makes it difficult to find and fix bugs.
ddb{0}> zx
ddb{0}> fjb1YW
Booting bsd.sp hangs after:
pckbc0 at isa0 port 0x60/5 irq 1 irq 12
pckbd0 at pckbc0 (kbd slot)
wskbd0 at pckbd0: console keyboard
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
Booting bsd.mp with acpi disabled gives me:
root on sd0a (d986443fd835edf5.a) swap on sd0b dump on sd0b
bnx0: address 00:1c:c4:a8:63:94
brgphy0 at bnx0 phy 2: BCM5708S 1000/2500baseSX PHY, rev. 1
bnx1: address 00:1c:c4:a8:63:8c
brgphy1 at bnx1 phy 2: BCM5708S 1000/2500baseSX PHY, rev. 1
uvm_fault(0xffffffff8193ae00, 0x60, 0, 1) -> e
kernel: page fault trap, code=0
Stopped at acpi_get_table_with_size+0x24: movq
clean_idt+0x40(%rax),%r
ddb>
Again with keyboard unresponsive. I guess that makes sense, there
probably aren't many machines with bnx without ACPI.
dmesg from CD boot with ACPI disabled below. Please let me know if
you'd like to see any other info from this system. Thanks.
# dmesg | more
OpenBSD 6.0-current (RAMDISK_CD) #2173: Thu Aug 25 23:16:10 MDT 2016
[email protected]:/usr/src/sys/arch/amd64/compile/RAMDISK_CD
real mem = 6423851008 (6126MB)
avail mem = 6227447808 (5938MB)
User Kernel Config
UKC> disable acpi
213 acpi0 disabled
UKC> quit
Continuing...
mainbus0 at root
bios0 at mainbus0: SMBIOS rev. 2.4 @ 0xee000 (73 entries)
bios0: vendor HP version "I15" date 05/02/2011
bios0: HP ProLiant BL460c G1
acpi at bios0 not configured
mpbios0 at bios0: Intel MP Specification 1.4
cpu0 at mainbus0: apid 4 (boot processor)
cpu0: Intel(R) Xeon(R) CPU X5355 @ 2.66GHz, 2685.92 MHz
cpu0:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,DCA,NXE,LONG,LAHF,PERF,SENSOR
cpu0: 4MB 64b/line 16-way L2 cache
cpu0: apic clock running at 333MHz
cpu0: mwait min=64, max=64, C-substates=0.2, IBE
cpu at mainbus0: not configured
cpu at mainbus0: not configured
cpu at mainbus0: not configured
cpu at mainbus0: not configured
cpu at mainbus0: not configured
cpu at mainbus0: not configured
cpu at mainbus0: not configured
mpbios0: bus 0 is type PCI
mpbios0: bus 1 is type PCI
mpbios0: bus 2 is type PCI
mpbios0: bus 3 is type PCI
mpbios0: bus 4 is type PCI
mpbios0: bus 5 is type PCI
mpbios0: bus 6 is type PCI
mpbios0: bus 7 is type PCI
mpbios0: bus 8 is type PCI
mpbios0: bus 9 is type PCI
mpbios0: bus 10 is type PCI
mpbios0: bus 164 is type PCI
mpbios0: bus 168 is type PCI
mpbios0: bus 13 is type PCI
mpbios0: bus 16 is type PCI
mpbios0: bus 19 is type PCI
mpbios0: bus 22 is type PCI
mpbios0: bus 188 is type PCI
mpbios0: bus 39 is type ISA
ioapic0 at mainbus0: apid 8 pa 0xfec00000, version 20, 24 pins
pci0 at mainbus0 bus 0
pchb0 at pci0 dev 0 function 0 "Intel 5000P Host" rev 0xb1
ppb0 at pci0 dev 2 function 0 "Intel 5000 PCIE" rev 0xb1
pci1 at ppb0 bus 4
ppb1 at pci1 dev 0 function 0 "Intel 6321ESB PCIE" rev 0x01
pci2 at ppb1 bus 5
ppb2 at pci2 dev 0 function 0 "Intel 6321ESB PCIE" rev 0x01
pci3 at ppb2 bus 6
ppb3 at pci3 dev 0 function 0 "ServerWorks PCIE-PCIX" rev 0xc3
pci4 at ppb3 bus 7
bnx0 at pci4 dev 0 function 0 "Broadcom BCM5708S" rev 0x12: apic 8 int
16
ppb4 at pci2 dev 1 function 0 "Intel 6321ESB PCIE" rev 0x01
pci5 at ppb4 bus 8
ppb5 at pci1 dev 0 function 3 "Intel 6321ESB PCIE-PCIX" rev 0x01
pci6 at ppb5 bus 9
ppb6 at pci0 dev 3 function 0 "Intel 5000 PCIE" rev 0xb1
pci7 at ppb6 bus 10
ppb7 at pci7 dev 0 function 0 "ServerWorks PCIE-PCIX" rev 0xb4
pci8 at ppb7 bus 11
ppb8 at pci8 dev 4 function 0 "ServerWorks HT-1000 PCIX" rev 0xb2
pci9 at ppb8 bus 12
ciss0 at pci8 dev 8 function 0 "Hewlett-Packard Smart Array" rev 0x00:
apic 8 int 18
ciss0: 1 LD, HW rev 0, FW 1.86/1.86
scsibus0 at ciss0: 1 targets
sd0 at scsibus0 targ 0 lun 0: <HP, LOGICAL VOLUME, 1.86> SCSI3 0/direct
fixed
sd0: 69970MB, 512 bytes/sector, 143299800 sectors
ppb9 at pci0 dev 4 function 0 "Intel 5000 PCIE" rev 0xb1
pci10 at ppb9 bus 13
ppb10 at pci0 dev 5 function 0 "Intel 5000 PCIE" rev 0xb1
pci11 at ppb10 bus 16
ppb11 at pci0 dev 6 function 0 "Intel 5000 PCIE" rev 0xb1
pci12 at ppb11 bus 19
qle0 at pci12 dev 0 function 0 "QLogic ISP2432" rev 0x02: msi
qle0: bad startup mboxes: 0 0
qle0: firmware rev 4.0.20, attrs 0x2
scsibus1 at qle0: 2048 targets, WWPN 500110a00086a868, WWNN
500110a00086a869
qle1 at pci12 dev 0 function 1 "QLogic ISP2432" rev 0x02: msi
qle1: bad startup mboxes: 0 0
qle1: firmware rev 4.0.20, attrs 0x2
scsibus2 at qle1: 2048 targets, WWPN 500110a00086a86a, WWNN
500110a00086a86b
ppb12 at pci0 dev 7 function 0 "Intel 5000 PCIE" rev 0xb1
pci13 at ppb12 bus 22
pchb1 at pci0 dev 16 function 0 "Intel 5000 Error Reporting" rev 0xb1
pchb2 at pci0 dev 16 function 1 "Intel 5000 Error Reporting" rev 0xb1
pchb3 at pci0 dev 16 function 2 "Intel 5000 Error Reporting" rev 0xb1
pchb4 at pci0 dev 17 function 0 "Intel 5000 Reserved" rev 0xb1
pchb5 at pci0 dev 19 function 0 "Intel 5000 Reserved" rev 0xb1
pchb6 at pci0 dev 21 function 0 "Intel 5000 FBD" rev 0xb1
pchb7 at pci0 dev 22 function 0 "Intel 5000 FBD" rev 0xb1
ppb13 at pci0 dev 28 function 0 "Intel 6321ESB PCIE" rev 0x09
pci14 at ppb13 bus 2
ppb14 at pci14 dev 0 function 0 "ServerWorks PCIE-PCIX" rev 0xc3
pci15 at ppb14 bus 3
bnx1 at pci15 dev 0 function 0 "Broadcom BCM5708S" rev 0x12: apic 8 int
16
uhci0 at pci0 dev 29 function 0 "Intel 6321ESB USB" rev 0x09: apic 8 int
16
uhci1 at pci0 dev 29 function 1 "Intel 6321ESB USB" rev 0x09: apic 8 int
17
uhci2 at pci0 dev 29 function 2 "Intel 6321ESB USB" rev 0x09: apic 8 int
18
uhci3 at pci0 dev 29 function 3 "Intel 6321ESB USB" rev 0x09: apic 8 int
19
ehci0 at pci0 dev 29 function 7 "Intel 6321ESB USB" rev 0x09: apic 8 int
16
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1
ppb15 at pci0 dev 30 function 0 "Intel 82801BA Hub-to-PCI" rev 0xd9
pci16 at ppb15 bus 1
vga1 at pci16 dev 3 function 0 "ATI ES1000" rev 0x02
wsdisplay1 at vga1 mux 1: console (80x25, vt100 emulation)
"Compaq iLO" rev 0x03 at pci16 dev 4 function 0 not configured
"Compaq iLO" rev 0x03 at pci16 dev 4 function 2 not configured
uhci4 at pci16 dev 4 function 4 "Hewlett-Packard USB" rev 0x00: apic 8
int 22
"Hewlett-Packard IPMI" rev 0x00 at pci16 dev 4 function 6 not configured
usb1 at uhci4: USB revision 1.0
uhub1 at usb1 "Hewlett-Packard UHCI root hub" rev 1.00/1.00 addr 1
"Intel 6321ESB LPC" rev 0x09 at pci0 dev 31 function 0 not configured
usb2 at uhci0: USB revision 1.0
uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb3 at uhci1: USB revision 1.0
uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb4 at uhci2: USB revision 1.0
uhub4 at usb4 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb5 at uhci3: USB revision 1.0
uhub5 at usb5 "Intel UHCI root hub" rev 1.00/1.00 addr 1
isa0 at mainbus0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com0: probed fifo depth: 0 bytes
com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5 irq 1 irq 12
pckbd0 at pckbc0 (kbd slot)wskbd0 at pckbd0: console keyboard, using
wsdisplay1
uhidev0 at uhub1 port 1 configuration 1 interface 0 "HP Virtual
Keyboard" rev 1.10/0.02 addr 2
uhidev0: iclass 3/1
ukbd0 at uhidev0
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay1
uhidev1 at uhub1 port 1 configuration 1 interface 1 "HP Virtual
Keyboard" rev 1.10/0.02 addr 2
uhidev1: iclass 3/1
uhid at uhidev1 not configured
uhub6 at uhub1 port 2 "HP Virtual Hub" rev 1.10/0.01 addr 3
umass0 at uhub6 port 2 configuration 1 interface 0 "HP Virtual CD-ROM"
rev 1.10/0.03 addr 4
umass0: using ATAPI over Bulk-Only
scsibus3 at umass0: 2 targets, initiator 0
cd0 at scsibus3 targ 1 lun 0: <HP, Virtual DVD-ROM, 0.0> ATAPI 5/cdrom
removable
softraid0 at root
scsibus4 at softraid0: 256 targets
root on rd0a swap on rd0b dump on rd0b
bnx0: address 00:1c:c4:a8:63:94
brgphy0 at bnx0 phy 2: BCM5708S 1000/2500baseSX PHY, rev. 1
bnx1: address 00:1c:c4:a8:63:8c
brgphy1 at bnx1 phy 2: BCM5708S 1000/2500baseSX PHY, rev. 1
