This isn't expected to work at all. That is why it was disabled. You'll need to upgrade the Hypervisor to -current, or to 6.1 when it is released.
On 2016 Oct 22 (Sat) at 00:06:08 -0200 (-0200), R0me0 *** wrote: :Hello misc. : :For testing purposes : :I compiled kernel with vmd support. : :After start the vm -> vmctl start "myvm" -m 512M -i 1 -d disk.img -k /bsd.rd : :I created a bridge and added vether0 and tap0 : :In the vm I have configured an ip 192.168.1.30 : :If I perform ping from OpenBSD Hypervisor -> ping 192.168.1.30 all packages :are send and received "on the fly" : :But if I perform the same step from "myvm", there is no packet loss but the :packets take so long to be send and consecutively replied : :I am performing this tests on Linux running Vmware Workstation 12 . : :Is this behavior expected ? : :Any directions will be appreciated. : :Thank you : :myvm dmesg: : :OpenBSD 6.0 (RAMDISK_CD) #2100: Tue Jul 26 13:05:59 MDT 2016 : dera...@amd64.openbsd.org:/usr/src/sys/arch/amd64/compile/RAMDISK_CD :RTC BIOS diagnostic error 20<config_unit> :real mem = 520093696 (496MB) :avail mem = 502673408 (479MB) :mainbus0 at root :bios0 at mainbus0 :acpi at bios0 not configured :cpu0 at mainbus0: (uniprocessor) :cpu0: Intel(R) Core(TM) i7-4810MQ CPU @ 2.80GHz, 14335.74 MHz :cpu0: :FPU,VME,DE,PSE,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,MMX,FXSR,SSE,SSE2,SS,SSE3,PCLMUL,SSSE3,FMA3,CX16,PCID,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,AVX,F1 :6C,RDRAND,HV,ITSC,FSGSBASE,BMI1,AVX2,SMEP,BMI2,ERMS,INVPCID,ARAT :pvbus0 at mainbus0: OpenBSD :pci0 at mainbus0 bus 0 :pchb0 at pci0 dev 0 function 0 "OpenBSD VMM PCI Host Bridge" rev 0x00 :virtio0 at pci0 dev 1 function 0 "Qumranet Virtio RNG" rev 0x00 :viornd0 at virtio0 :virtio0: irq 3 :virtio1 at pci0 dev 2 function 0 "Qumranet Virtio Storage" rev 0x00 :vioblk0 at virtio1 :scsibus0 at vioblk0: 2 targets :sd0 at scsibus0 targ 0 lun 0: <VirtIO, Block Device, > SCSI3 0/direct fixed :sd0: 5120MB, 512 bytes/sector, 10485760 sectors :virtio1: irq 5 :virtio2 at pci0 dev 3 function 0 "Qumranet Virtio Network" rev 0x00 :vio0 at virtio2: address fe:e1:ba:d0:d0:94 :virtio2: irq 9 :isa0 at mainbus0 :com0 at isa0 port 0x3f8/8 irq 4: ns8250, no fifo :com0: console :softraid0 at root :scsibus1 at softraid0: 256 targets :root on rd0a swap on rd0b dump on rd0b :WARNING: invalid time in clock chip :WARNING: CHECK AND RESET THE DATE! : :openbsd hypervisor : : : :OpenBSD 6.0-stable (GENERIC.MP) #0: Fri Oct 21 20:07:42 BRST 2016 : root@puffysor.localdomain:/usr/src/sys/arch/amd64/compile/GENERIC.MP :real mem = 2130640896 (2031MB) :avail mem = 2061631488 (1966MB) :mpath0 at root :scsibus0 at mpath0: 256 targets :mainbus0 at root :bios0 at mainbus0: SMBIOS rev. 2.7 @ 0xe0010 (242 entries) :bios0: vendor Phoenix Technologies LTD version "6.00" date 07/02/2015 :bios0: VMware, Inc. VMware Virtual Platform :acpi0 at bios0: rev 2 :acpi0: sleep states S0 S1 S4 S5 :acpi0: tables DSDT FACP BOOT APIC MCFG SRAT HPET WAET :acpi0: wakeup devices PCI0(S3) USB_(S1) P2P0(S3) S1F0(S3) S2F0(S3) S3F0(S3) :S4F0(S3) S5F0(S3) S6F0(S3) S7F0(S3) S8F0(S3) S9F0(S3) S10F(S3) S11F(S3) :S12F(S3) S13F(S3) [...] :acpitimer0 at acpi0: 3579545 Hz, 24 bits :acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat :cpu0 at mainbus0: apid 0 (boot processor) :cpu0: Intel(R) Core(TM) i7-4810MQ CPU @ 2.80GHz, 3800.69 MHz :cpu0: :FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,MMX,FXSR,SSE,SSE2,SS,HTT,SSE3,PCLMUL,VMX,SSSE3,FMA3,CX16,PCID,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLIN :E,AES,XSAVE,AVX,F16C,RDRAND,HV,NXE,PAGE1GB,LONG,LAHF,ABM,PERF,ITSC,FSGSBASE,BMI1,AVX2,SMEP,BMI2,ERMS,INVPCID,SENSOR,ARAT : :cpu0: 256KB 64b/line 8-way L2 cache :cpu0: smt 0, core 0, package 0 :mtrr: Pentium Pro MTRR support, 8 var ranges, 88 fixed ranges :cpu0: apic clock running at 65MHz :cpu1 at mainbus0: apid 1 (application processor) :cpu1: Intel(R) Core(TM) i7-4810MQ CPU @ 2.80GHz, 3810.50 MHz :cpu1: :FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,MMX,FXSR,SSE,SSE2,SS,HTT,SSE3,PCLMUL,VMX,SSSE3,FMA3,CX16,PCID,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLIN :E,AES,XSAVE,AVX,F16C,RDRAND,HV,NXE,PAGE1GB,LONG,LAHF,ABM,PERF,ITSC,FSGSBASE,BMI1,AVX2,SMEP,BMI2,ERMS,INVPCID,SENSOR,ARAT : :cpu1: 256KB 64b/line 8-way L2 cache :cpu1: smt 0, core 1, package 0 :ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 11, 24 pins :acpimcfg0 at acpi0 addr 0xf0000000, bus 0-127 :acpihpet0 at acpi0: 14318179 Hz :acpiprt0 at acpi0: bus 0 (PCI0) :acpicpu0 at acpi0: C1(@1 halt!) :acpicpu1 at acpi0: C1(@1 halt!) :"PNP0001" at acpi0 not configured :"PNP0303" at acpi0 not configured :"VMW0003" at acpi0 not configured :"PNP0A05" at acpi0 not configured :acpiac0 at acpi0: AC unit online :pvbus0 at mainbus0: VMware :vmt0 at pvbus0 :pci0 at mainbus0 bus 0 :pchb0 at pci0 dev 0 function 0 "Intel 82443BX AGP" rev 0x01 :ppb0 at pci0 dev 1 function 0 "Intel 82443BX AGP" rev 0x01 :pci1 at ppb0 bus 1 :pcib0 at pci0 dev 7 function 0 "Intel 82371AB PIIX4 ISA" rev 0x08 :pciide0 at pci0 dev 7 function 1 "Intel 82371AB IDE" rev 0x01: DMA, channel :0 configured to compatibility, channel 1 configured to compatibility :pciide0: channel 0 disabled (no drives) :atapiscsi0 at pciide0 channel 1 drive 0 :scsibus1 at atapiscsi0: 2 targets :cd0 at scsibus1 targ 0 lun 0: <NECVMWar, VMware IDE CDR10, 1.00> ATAPI :5/cdrom removable :cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2 :piixpm0 at pci0 dev 7 function 3 "Intel 82371AB Power" rev 0x08: SMBus :disabled :"VMware VMCI" rev 0x10 at pci0 dev 7 function 7 not configured :vga1 at pci0 dev 15 function 0 "VMware SVGA II" rev 0x00 :wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation) :wsdisplay0: screen 1-5 added (80x25, vt100 emulation) :mpi0 at pci0 dev 16 function 0 "Symbios Logic 53c1030" rev 0x01: apic 2 int :17 :mpi0: 0, firmware 1.3.41.32 :scsibus2 at mpi0: 16 targets, initiator 7 :sd0 at scsibus2 targ 0 lun 0: <VMware,, VMware Virtual S, 1.0> SCSI2 :0/direct fixed :sd0: 20480MB, 512 bytes/sector, 41943040 sectors :mpi0: target 0 Sync at 160MHz width 16bit offset 127 QAS 1 DT 1 IU 1 :ppb1 at pci0 dev 17 function 0 "VMware PCI" rev 0x02 :pci2 at ppb1 bus 2 :uhci0 at pci2 dev 0 function 0 "VMware UHCI" rev 0x00: apic 2 int 18 :em0 at pci2 dev 1 function 0 "Intel 82545EM" rev 0x01: apic 2 int 19, :address 00:0c:29:12:f6:9f :ehci0 at pci2 dev 2 function 0 "VMware EHCI" rev 0x00: apic 2 int 16 :usb0 at ehci0: USB revision 2.0 :uhub0 at usb0 "VMware EHCI root hub" rev 2.00/1.00 addr 1 :usb1 at uhci0: USB revision 1.0 :uhub1 at usb1 "VMware UHCI root hub" rev 1.00/1.00 addr 1 :ppb2 at pci0 dev 21 function 0 "VMware PCIE" rev 0x01 :pci3 at ppb2 bus 3 :ppb3 at pci0 dev 21 function 1 "VMware PCIE" rev 0x01 :pci4 at ppb3 bus 4 :ppb4 at pci0 dev 21 function 2 "VMware PCIE" rev 0x01 :pci5 at ppb4 bus 5 :ppb5 at pci0 dev 21 function 3 "VMware PCIE" rev 0x01 :pci6 at ppb5 bus 6 :ppb6 at pci0 dev 21 function 4 "VMware PCIE" rev 0x01 :pci7 at ppb6 bus 7 :ppb7 at pci0 dev 21 function 5 "VMware PCIE" rev 0x01 :pci8 at ppb7 bus 8 :ppb8 at pci0 dev 21 function 6 "VMware PCIE" rev 0x01 :pci9 at ppb8 bus 9 :ppb9 at pci0 dev 21 function 7 "VMware PCIE" rev 0x01 :pci10 at ppb9 bus 10 :ppb10 at pci0 dev 22 function 0 "VMware PCIE" rev 0x01 :pci11 at ppb10 bus 11 :ppb11 at pci0 dev 22 function 1 "VMware PCIE" rev 0x01 :pci12 at ppb11 bus 12 :ppb12 at pci0 dev 22 function 2 "VMware PCIE" rev 0x01 :pci13 at ppb12 bus 13 :ppb13 at pci0 dev 22 function 3 "VMware PCIE" rev 0x01 :pci14 at ppb13 bus 14 :ppb14 at pci0 dev 22 function 4 "VMware PCIE" rev 0x01 :pci15 at ppb14 bus 15 :ppb15 at pci0 dev 22 function 5 "VMware PCIE" rev 0x01 :pci16 at ppb15 bus 16 :ppb16 at pci0 dev 22 function 6 "VMware PCIE" rev 0x01 :pci17 at ppb16 bus 17 :ppb17 at pci0 dev 22 function 7 "VMware PCIE" rev 0x01 :pci18 at ppb17 bus 18 :ppb18 at pci0 dev 23 function 0 "VMware PCIE" rev 0x01 :pci19 at ppb18 bus 19 :ppb19 at pci0 dev 23 function 1 "VMware PCIE" rev 0x01 :pci20 at ppb19 bus 20 :ppb20 at pci0 dev 23 function 2 "VMware PCIE" rev 0x01 :pci21 at ppb20 bus 21 :ppb21 at pci0 dev 23 function 3 "VMware PCIE" rev 0x01 :pci22 at ppb21 bus 22 :ppb22 at pci0 dev 23 function 4 "VMware PCIE" rev 0x01 :pci23 at ppb22 bus 23 :ppb23 at pci0 dev 23 function 5 "VMware PCIE" rev 0x01 :pci24 at ppb23 bus 24 :ppb24 at pci0 dev 23 function 6 "VMware PCIE" rev 0x01 :pci25 at ppb24 bus 25 :ppb25 at pci0 dev 23 function 7 "VMware PCIE" rev 0x01 :pci26 at ppb25 bus 26 :ppb26 at pci0 dev 24 function 0 "VMware PCIE" rev 0x01 :pci27 at ppb26 bus 27 :ppb27 at pci0 dev 24 function 1 "VMware PCIE" rev 0x01 :pci28 at ppb27 bus 28 :ppb28 at pci0 dev 24 function 2 "VMware PCIE" rev 0x01 :pci29 at ppb28 bus 29 :ppb29 at pci0 dev 24 function 3 "VMware PCIE" rev 0x01 :pci30 at ppb29 bus 30 :ppb30 at pci0 dev 24 function 4 "VMware PCIE" rev 0x01 :pci31 at ppb30 bus 31 :ppb31 at pci0 dev 24 function 5 "VMware PCIE" rev 0x01 :pci32 at ppb31 bus 32 :ppb32 at pci0 dev 24 function 6 "VMware PCIE" rev 0x01 :pci33 at ppb32 bus 33 :ppb33 at pci0 dev 24 function 7 "VMware PCIE" rev 0x01 :pci34 at ppb33 bus 34 :isa0 at pcib0 :isadma0 at isa0 :pckbc0 at isa0 port 0x60/5 irq 1 irq 12 :pckbd0 at pckbc0 (kbd slot) :wskbd0 at pckbd0: console keyboard, using wsdisplay0 :pms0 at pckbc0 (aux slot) :wsmouse0 at pms0 mux 0 :pcppi0 at isa0 port 0x61 :spkr0 at pcppi0 :vmm0 at mainbus0: VMX/EPT :uhidev0 at uhub1 port 1 configuration 1 interface 0 "VMware VMware Virtual :USB Mouse" rev 1.10/1.02 addr 2 :uhidev0: iclass 3/0 :ums0 at uhidev0: 16 buttons, Z and W dir :wsmouse1 at ums0 mux 0 :uhidev1 at uhub1 port 1 configuration 1 interface 1 "VMware VMware Virtual :USB Mouse" rev 1.10/1.02 addr 2 :uhidev1: iclass 3/0 :ums1 at uhidev1: 16 buttons, Z and W dir :wsmouse2 at ums1 mux 0 :uhub2 at uhub1 port 2 "VMware VMware Virtual USB Hub" rev 1.10/1.00 addr 3 :vscsi0 at root :scsibus3 at vscsi0: 256 targets :softraid0 at root :scsibus4 at softraid0: 256 targets :root on sd0a (9b5dfcf2ffc19ce3.a) swap on sd0b dump on sd0b :arp: attempt to add entry for 192.168.1.30 on vether0 by fe:e1:ba:d0:d0:94 :on tap0 : -- While money doesn't buy love, it puts you in a great bargaining position.
