I try this for a while too. (https://marc.info/?l=openbsd-misc&m=147945720728652&w=2)
Interesting that it works when installing from cd. But when I get you right you stuck in the reboot-loop too when trying to boot from usb (install##.fs / miniroot##.fs) I removed my super-drive and put a second ssd in, on which I want to install OpenBSD. I also recognised something similar when installing OpenBSD to a PC-Engine APU.2 board. On the APU.2 you only have to set correct serial output device at boot> and everything works fine. Maybe it is also needed to set some kind of efi-device ?!? I did´t find the time to further investigate in this direction but maybe someone on the list can help? -- best mirac 2016-12-28 3:24 GMT+01:00 Byron Klippert <[email protected]>: > Hello Misc, > > Recently tried to get my intel macbook (circa '08) dual-booting with > -current amd64 (December 26 snapshot). > > Within OSX I repartitioned the RootDisk and added a MS-DOS (FAT) > partition for the OpenBSD install/disklabel. I booted from CD and > installed to wd0 (using the OpenBSD fdisk partition). At this stage if I > want to boot from wd0, I have to boot from CD and select hd0a:/bsd at > the second stage boot loader. This works well enough, dmesg of the > system below. > > When trying to boot directly from wd0 using the native EFI bootloader I > placed BOOTIA32.EFI and BOOTX64.EFI in the EFI partition of the RootDisk > so that I can select "EFI Partition" when booting (by holding option > key). > > /dev/disk0 > #: TYPE > NAME SIZE IDENTIFIER > 0: > GUID_partition_scheme *120.0 > GB disk0 > 1: > EFI 209.7 MB disk0s1 > 2: Apple_HFS > RootDisk 118.6 GB disk0s2 > 3: Microsoft Basic > Data 1.1 GB disk0s3 > > > This setup gets as far as shown below and then stops... > > probing: pc0 mem[572K 64K 3039M 11M 60K 48K] > disk: hd0 > >> OpenBSD/amd64 BOOTIA32 3.32 > boot> > booting hd0a:/bsd: 6979304+2212872+258624+0+765952 > [72+710280+477696]=0xae2350 > entry point at 0xf001000 [7205c766, 34000004, 24448b12, 1240a304] > > > I've tried booting with `boot> hd0a:/bsd.rd'. Also tried writing > install60.tgz and miniroot60.tgz to USB and got similar results there as > well. > > > Curious to know if the native EFI bootloader is designed to work with > this hardware? > > Thanks, > > dmesg output: > > OpenBSD 6.0-current (GENERIC.MP) #73: Mon Dec 26 23:25:48 MST 2016 > [email protected]:/usr/src/sys/arch/amd64/compile/GENERIC.MP > real mem = 3171909632 (3024MB) > avail mem = 3071180800 (2928MB) > warning: no entropy supplied by boot loader > mpath0 at root > scsibus0 at mpath0: 256 targets > mainbus0 at root > bios0 at mainbus0: SMBIOS rev. 2.4 @ 0xe0000 (37 entries) > bios0: vendor Apple Inc. version "MB21.88Z.00A5.B07.0706270922" date > 06/27/07 > bios0: Apple Inc. MacBook2,1 > acpi0 at bios0: rev 2 > acpi0: sleep states S0 S3 S4 S5 > acpi0: tables DSDT FACP HPET APIC MCFG ASF! SBST ECDT SSDT SSDT SSDT > acpi0: wakeup devices ADP1(S3) LID0(S3) PXS1(S4) PXS2(S4) USB1(S3) > USB2(S3) USB3(S3) USB4(S3) USB7(S3) EC__(S3) > acpitimer0 at acpi0: 3579545 Hz, 24 bits > acpihpet0 at acpi0: 14318179 Hz > acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat > cpu0 at mainbus0: apid 0 (boot processor) > cpu0: Intel(R) Core(TM)2 CPU T7400 @ 2.16GHz, 2161.65 MHz > cpu0: > FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA, > CMOV,PAT,PSE36,CFLUS > H,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,DTES64, > MWAIT,DS-CPL,VMX,EST,TM > 2,SSSE3,CX16,xTPR,PDCM,NXE,LONG,LAHF,PERF,SENSOR > cpu0: 4MB 64b/line 16-way L2 cache > cpu0: smt 0, core 0, package 0 > mtrr: Pentium Pro MTRR support, 8 var ranges, 88 fixed ranges > cpu0: apic clock running at 166MHz > cpu0: mwait min=64, max=64, C-substates=0.2.2.2.2, IBE > cpu1 at mainbus0: apid 1 (application processor) > cpu1: Intel(R) Core(TM)2 CPU T7400 @ 2.16GHz, 2161.25 MHz > cpu1: > FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA, > CMOV,PAT,PSE36,CFLUS > H,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,DTES64, > MWAIT,DS-CPL,VMX,EST,TM > 2,SSSE3,CX16,xTPR,PDCM,NXE,LONG,LAHF,PERF,SENSOR > cpu1: 4MB 64b/line 16-way L2 cache > cpu1: smt 0, core 1, package 0 > ioapic0 at mainbus0: apid 1 pa 0xfec00000, version 20, 24 pins > acpimcfg0 at acpi0 addr 0xf0000000, bus 0-255 > acpiec0 at acpi0 > acpiprt0 at acpi0: bus 0 (PCI0) > acpiprt1 at acpi0: bus 1 (RP01) > acpiprt2 at acpi0: bus 2 (RP02) > acpiprt3 at acpi0: bus 3 (PCIB) > acpicpu0 at acpi0: !C3(100@55 mwait@0x31), !C2(500@1 mwait@0x10), > C1(1000@1 mwait), PSS > acpicpu1 at acpi0: !C3(100@55 mwait@0x31), !C2(500@1 mwait@0x10), > C1(1000@1 mwait), PSS > acpiac0 at acpi0: AC unit online > acpibtn0 at acpi0: LID0 > "APP0002" at acpi0 not configured > acpibtn1 at acpi0: PWRB > acpibtn2 at acpi0: SLPB > "APP0001" at acpi0 not configured > "APP0003" at acpi0 not configured > "ACPI0002" at acpi0 not configured > acpibat0 at acpi0: BAT0 model "15253732082930497" type 15253732284385612 > oem "15253732284387396" > acpivideo0 at acpi0: GFX0 > cpu0: Enhanced SpeedStep 2161 MHz: speeds: 2167, 2000, 1833, 1667, 1500, > 1333, 1000 MHz > memory map conflict 0xbef00000/0x100000 > memory map conflict 0xbf000000/0x1000000 > memory map conflict 0xf00f8000/0x1000 > memory map conflict 0xfed1c000/0x4000 > memory map conflict 0xfffb0000/0x30000 > pci0 at mainbus0 bus 0 > pchb0 at pci0 dev 0 function 0 "Intel 82945GM Host" rev 0x03 > inteldrm0 at pci0 dev 2 function 0 "Intel 82945GM Video" rev 0x03 > drm0 at inteldrm0 > intagp0 at inteldrm0 > agp0 at intagp0: aperture at 0xc0000000, size 0x10000000 > inteldrm0: apic 1 int 16 > inteldrm0: 1280x800 > wsdisplay0 at inteldrm0 mux 1: console (std, vt100 emulation) > wsdisplay0: screen 1-5 added (std, vt100 emulation) > "Intel 82945GM Video" rev 0x03 at pci0 dev 2 function 1 not configured > vendor "Intel", unknown product 0x27a3 (class DASP subclass Time and > Frequency, rev 0x03) at pci0 dev 7 function 0 not configured > azalia0 at pci0 dev 27 function 0 "Intel 82801GB HD Audio" rev 0x02: msi > azalia0: codecs: Sigmatel STAC9220/1 > audio0 at azalia0 > ppb0 at pci0 dev 28 function 0 "Intel 82801GB PCIE" rev 0x02: msi > pci1 at ppb0 bus 1 > mskc0 at pci1 dev 0 function 0 "Marvell Yukon 88E8053" rev 0x22, Yukon-2 > EC rev. A3 (0x2): apic 1 int 16 > msk0 at mskc0 port A: address 00:19:e3:3d:46:17 > eephy0 at msk0 phy 0: 88E1111 Gigabit PHY, rev. 2 > ppb1 at pci0 dev 28 function 1 "Intel 82801GB PCIE" rev 0x02: msi > pci2 at ppb1 bus 2 > athn0 at pci2 dev 0 function 0 "Atheros AR5418" rev 0x01: apic 1 int 17 > athn0: MAC AR5418 rev 2, RF AR5133 (2T3R), ROM rev 4, address > 00:1b:63:c5:77:67 > uhci0 at pci0 dev 29 function 0 "Intel 82801GB USB" rev 0x02: apic 1 int > 21 > uhci1 at pci0 dev 29 function 1 "Intel 82801GB USB" rev 0x02: apic 1 int > 19 > uhci2 at pci0 dev 29 function 2 "Intel 82801GB USB" rev 0x02: apic 1 int > 18 > uhci3 at pci0 dev 29 function 3 "Intel 82801GB USB" rev 0x02: apic 1 int > 16 > ehci0 at pci0 dev 29 function 7 "Intel 82801GB USB" rev 0x02: apic 1 int > 21 > usb0 at ehci0: USB revision 2.0 > uhub0 at usb0 configuration 1 interface 0 "Intel EHCI root hub" rev > 2.00/1.00 addr 1 > ppb2 at pci0 dev 30 function 0 "Intel 82801BAM Hub-to-PCI" rev 0xe2 > pci3 at ppb2 bus 3 > "AT&T/Lucent FW322 1394" rev 0x61 at pci3 dev 3 function 0 not > configured > pcib0 at pci0 dev 31 function 0 "Intel 82801GBM LPC" rev 0x02 > pciide0 at pci0 dev 31 function 1 "Intel 82801GB IDE" rev 0x02: DMA, > channel 0 configured to compatibility, channel 1 configured to > compatibility > atapiscsi0 at pciide0 channel 0 drive 0 > scsibus1 at atapiscsi0: 2 targets > cd0 at scsibus1 targ 0 lun 0: <MATSHITA, DVD-R UJ-857E, ZB0E> ATAPI > 5/cdrom removable > cd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 4 > pciide0: channel 1 disabled (no drives) > pciide1 at pci0 dev 31 function 2 "Intel 82801GBM SATA" rev 0x02: DMA, > channel 0 configured to native-PCI, channel 1 configured to native-PCI > pciide1: using apic 1 int 19 for native-PCI interrupt > wd0 at pciide1 channel 0 drive 1: <KINGSTON SKC300S37A120G> > wd0: 1-sector PIO, LBA48, 114473MB, 234441648 sectors > wd0(pciide1:0:1): using PIO mode 4, Ultra-DMA mode 6 > ichiic0 at pci0 dev 31 function 3 "Intel 82801GB SMBus" rev 0x02: apic 1 > int 19 > iic0 at ichiic0 > iic0: addr 0x48 00=2e 01=00 02=4b 03=50 words 00=2e00 01=00ff 02=4b00 > 03=5000 04=ffff 05=ffff 06=ffff 07=ffff > spdmem0 at iic0 addr 0x50: 2GB DDR2 SDRAM non-parity PC2-5300CL5 SO-DIMM > spdmem1 at iic0 addr 0x52: 2GB DDR2 SDRAM non-parity PC2-5300CL5 SO-DIMM > usb1 at uhci0: USB revision 1.0 > uhub1 at usb1 configuration 1 interface 0 "Intel UHCI root hub" rev > 1.00/1.00 addr 1 > usb2 at uhci1: USB revision 1.0 > uhub2 at usb2 configuration 1 interface 0 "Intel UHCI root hub" rev > 1.00/1.00 addr 1 > usb3 at uhci2: USB revision 1.0 > uhub3 at usb3 configuration 1 interface 0 "Intel UHCI root hub" rev > 1.00/1.00 addr 1 > usb4 at uhci3: USB revision 1.0 > uhub4 at usb4 configuration 1 interface 0 "Intel UHCI root hub" rev > 1.00/1.00 addr 1 > isa0 at pcib0 > isadma0 at isa0 > pcppi0 at isa0 port 0x61 > spkr0 at pcppi0 > asmc0 at isa0 port 0x300/32: rev 1.17f517, 226 keys > vmm0 at mainbus0: VMX > drm: render error detected, EIR: 0x00000010 > drm: page table error > drm: PGTBL_ER: 0x00000102 > error: [drm:pid0:i915_report_and_clear_eir] *ERROR* EIR stuck: > 0x00000010, masking > drm: render error detected, EIR: 0x00000010 > drm: page table error > drm: PGTBL_ER: 0x00000102 > umass0 at uhub0 port 3 configuration 1 interface 0 "Lexar USB Flash > Drive" rev 2.00/11.00 addr 2 > umass0: using SCSI over Bulk-Only > scsibus2 at umass0: 2 targets, initiator 0 > sd0 at scsibus2 targ 1 lun 0: <Lexar, JD FireFly, 1100> SCSI0 0/direct > removable serial.05dca810N1HZPKUEG7GM > sd0: 3824MB, 512 bytes/sector, 7831552 sectors > ugen0 at uhub0 port 4 "Micron Built-in iSight" rev 2.00/1.89 addr 3 > uhidev0 at uhub1 port 2 configuration 1 interface 0 "Apple Computer > Apple Internal Keyboard / Trackpad" rev 2.00/0.18 addr 2 > uhidev0: iclass 3/1 > ukbd0 at uhidev0: 8 variable keys, 5 key codes, country code 33 > wskbd0 at ukbd0: console keyboard, using wsdisplay0 > uhidev1 at uhub1 port 2 configuration 1 interface 1 "Apple Computer > Apple Internal Keyboard / Trackpad" rev 2.00/0.18 addr 2 > uhidev1: iclass 3/1, 5 report ids > ums0 at uhidev1 reportid 2: 3 buttons > wsmouse0 at ums0 mux 0 > ums1 at uhidev1 reportid 5 > ums1: mouse has no X report > uhidev2 at uhub1 port 2 configuration 1 interface 2 "Apple Computer > Apple Internal Keyboard / Trackpad" rev 2.00/0.18 addr 2 > uhidev2: iclass 3/0 > uhid0 at uhidev2: input=1, output=0, feature=0 > uhidev3 at uhub3 port 2 configuration 1 interface 0 "Apple Computer, > Inc. IR Receiver" rev 2.00/1.10 addr 2 > uhidev3: iclass 3/0, 38 report ids > uhid1 at uhidev3 reportid 36: input=4, output=0, feature=0 > uhid2 at uhidev3 reportid 37: input=4, output=0, feature=0 > uhid3 at uhidev3 reportid 38: input=4, output=0, feature=0 > uhidev4 at uhub4 port 1 configuration 1 interface 0 "Apple Computer > HID-proxy" rev 2.00/19.65 addr 2 > uhidev4: iclass 3/1 > ukbd1 at uhidev4: 8 variable keys, 6 key codes > wskbd1 at ukbd1 mux 1 > wskbd1: connecting to wsdisplay0 > uhidev5 at uhub4 port 1 configuration 1 interface 1 "Apple Computer > HID-proxy" rev 2.00/19.65 addr 2 > uhidev5: iclass 3/1 > ums2 at uhidev5: 5 buttons > wsmouse1 at ums2 mux 0 > vscsi0 at root > scsibus3 at vscsi0: 256 targets > softraid0 at root > scsibus4 at softraid0: 256 targets > root on wd0a (157fa0187fd41f4c.a) swap on wd0b dump on wd0b > > > fdisk output: > > Disk: wd0 geometry: 14593/255/63 [234441648 Sectors] > Offset: 0 Signature: 0xAA55 > Starting Ending LBA > Info: > #: id C H S - C H S [ > start: size ] > ------------------------------------------------------------ > ----------------- > -- > 0: EE 0 0 2 - 25 127 14 [ > 1: 409639 ] EFI > GPT > 1: AF 25 127 15 - 14446 116 54 [ 409640: 231672712 > ] MacOS > X HFS+ > *2: A6 14462 215 26 - 14593 66 1 [ 232345600: 2095104 > ] > OpenBSD > 3: 00 0 0 0 - 0 0 0 [ > 0: 0 ] > unused > > > > -- > Byron Klippert > [email protected] > c. 867-336-1306 > > -- +49.179.1448024 Karl-Kunger-StraÃe 68 D - 12435 Berlin
