Hey friends,
i am trying out vmd and I have a little problem getting networking going
inside the guest machine. I am not sure if this is a problem in vmd or
simply my misconfiguration.
From my datacenter i got the following data:
Main Server (OpenBSD GENERIC.MP#99 amd64)
#########################################
IP: 144.76.102.204
Netmask: 255.255.255.224
Gateway: 144.76.102.193
Virtual Machine (OpenBSD GENERIC.MP#99 amd64)
#############################################
I got an entire subnet from the datacenter. 136.243.186.160/29 So i
decided to use the following IP in it.
IP: 136.243.186.161
Netmask: 255.255.255.248
Gateway: 144.76.102.204
According to there documentation they always route all subnets on the
main IP. In my case 144.76.102.204.
On my host I configured the em0 interface according to the datacenter
data and it works fine. The host who runs vmd is connected correctly. In
my /etc/vm.conf i created a switch called "uplink" and added em0 to it.
When i check the current config via ifconfig i get the following.
em0: flags=8b43<UP,BROADCAST,RUNNING,PROMISC,ALLMULTI,SIMPLEX,MULTICAST> mtu
1500
lladdr 90:1b:0e:8b:0f:34
description: hetzner-uplink
index 1 priority 0 llprio 3
groups: egress
media: Ethernet autoselect (1000baseT full-duplex,rxpause,txpause)
status: active
inet 144.76.102.204 netmask 0xffffffe0 broadcast 144.76.102.223
tap0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500
lladdr fe:e1:ba:d0:7e:0a
description: vm1-if0-foobar
index 5 priority 0 llprio 3
groups: tap
status: active
bridge0: flags=41<UP,RUNNING>
description: switch1-uplink
index 7 llprio 3
groups: bridge
priority 32768 hellotime 2 fwddelay 15 maxage 20 holdcnt 6 proto rstp
em0 flags=3<LEARNING,DISCOVER>
port 1 ifpriority 0 ifcost 0
tap0 flags=3<LEARNING,DISCOVER>
port 5 ifpriority 0 ifcost 0
Addresses (max cache: 100, timeout: 240):
0c:86:10:ed:35:58 em0 1 flags=0<>
My /etc/vm.conf looks like this:
switch "uplink" {
add em0
}
vm "foobar" {
memory 2G
disk "/tmp/1.vdi"
interface {
switch "uplink"
}
}
When i start the vm with my current /bsd.rd i start the installer and
insert the following:
Available network interfaces are: vio0 vlan0.
Which network interface do you wish to configure? (or 'done') [vio0]
IPv4 address for vio0? (or 'dhcp' or 'none') [dhcp] 136.243.186.161
Netmask for vio0? [255.255.255.248]
IPv6 address for vio0? (or 'autoconf' or 'none') [none]
Available network interfaces are: vio0 vlan0.
Which network interface do you wish to configure? (or 'done') [done]
Default IPv4 route? (IPv4 address or none) 144.76.102.204
add net default: gateway 144.76.102.204: Network is unreachable
Can you people see something that i might missed?
Big thanks in advance and greetings
Leo
