Hello,
I'm having a problem getting the wireless network to work on a ThinkPad
T40. The wireless seems to connect OK, but I can't get any packets
through it.
The device is ipw0 and it seems to be configured correctly as far as I
can see.
# cat /etc/hostname.ipw0
nwid anderella24
wpakey "password"
inet 192.168.28.79 255.255.255.0
I have the 1.3 firmware installed
# fw_update -i
Installed: radeondrm-firmware-20170119 ipw-firmware-1.3p2
intel-firmware-20180312v0
The card reports as connected to the wireless
# ifconfig -a
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 32768
index 4 priority 0 llprio 3
groups: lo
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4
inet 127.0.0.1 netmask 0xff000000
em0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
lladdr 00:16:41:a8:8d:8b
index 1 priority 0 llprio 3
media: Ethernet autoselect (none)
status: no carrier
ipw0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
lladdr 00:04:23:61:fe:6c
index 2 priority 4 llprio 3
groups: wlan egress
media: IEEE802.11 autoselect (DS11 mode 11b)
status: active
ieee80211: nwid anderella24 chan 13 bssid b0:39:56:4f:a9:14
-50dBm wpakey wpaprotos wpa2 wpaakms psk wpaciphers ccmp wpagroupcipher
ccmp
inet 192.168.28.79 netmask 0xffffff00 broadcast 192.168.28.255
enc0: flags=0<> index 3 priority 0 llprio 3
groups: enc
status: active
pflog0: flags=141<UP,RUNNING,PROMISC> mtu 33172
index 5 priority 0 llprio 3
groups: pflog
But when I try to ping an existing system using this interface, there
is no connection
I have another laptop (running Linux) which is connected to the same
wireless AP and this can ping the existing system OK
The wireless AP is a Netgear WAC104 and this shows the card as connected
Status Device Name BSSID SSID Type Radio MAC Address
Connection Type
Allowed Unknown B0:39:56:4F:A9:14 anderella24 WPA2-PSK 2.4G
00:04:23:61:FE:6C Wireless
Is anyone else using a similar network card and are they having any
problems?
Full dmesg below
OpenBSD 6.3 (GENERIC) #490: Sat Mar 24 14:31:33 MDT 2018
dera...@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel(R) Pentium(R) M processor 1500MHz ("GenuineIntel"
686-class) 1.50 GHz cpu0:
FPU,V86,DE,PSE,TSC,MSR,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,TM,PBE,EST,TM2,PERF
real mem = 1072578560 (1022MB) avail mem = 1039097856 (990MB)
mpath0 at root
scsibus0 at mpath0: 256 targets
mainbus0 at root
bios0 at mainbus0: date 02/27/06, BIOS32 rev. 0 @ 0xfd750, SMBIOS rev.
2.33 @ 0xe0010 (61 entries) bios0: vendor IBM version "1RETDOWW
(3.20 )" date 02/27/2006 bios0: IBM 237342G
acpi0 at bios0: rev 2
acpi0: sleep states S0 S3 S4 S5
acpi0: tables DSDT FACP SSDT ECDT TCPA BOOT
acpi0: wakeup devices LID_(S3) SLPB(S3) UART(S3) PCI0(S3) PCI1(S4)
USB0(S3) USB1(S3) AC9M(S4) acpitimer0 at acpi0: 3579545 Hz, 24 bits
acpiec0 at acpi0
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus 1 (AGP_)
acpiprt2 at acpi0: bus 2 (PCI1)
acpipwrres0 at acpi0: PUBS, resource for USB0, USB1, USB7
acpitz0 at acpi0: critical temperature is 93 degC
acpibtn0 at acpi0: LID_
acpibtn1 at acpi0: SLPB
"IBM0057" at acpi0 not configured
"IBM0071" at acpi0 not configured
acpibat0 at acpi0: BAT0 model "IBM-08K8193" serial 21133 type LION oem
"SANYO" acpiac0 at acpi0: AC unit online
acpithinkpad0 at acpi0
acpidock0 at acpi0: DOCK not docked (0)
acpivideo0 at acpi0: VID_
bios0: ROM list: 0xc0000/0x10000 0xd0000/0x1000 0xd1000/0x1000
0xdc000/0x4000! 0xe0000/0x10000 cpu0 at mainbus0: (uniprocessor)
mtrr: Pentium Pro MTRR support, 8 var ranges, 88 fixed ranges
cpu0: Enhanced SpeedStep 1496 MHz: speeds: 1500, 1400, 1200, 1000, 800,
600 MHz pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "Intel 82855PM Host" rev 0x03
intelagp0 at pchb0
agp0 at intelagp0: aperture at 0xd0000000, size 0x10000000
ppb0 at pci0 dev 1 function 0 "Intel 82855PM AGP" rev 0x03
pci1 at ppb0 bus 1
radeondrm0 at pci1 dev 0 function 0 "ATI Radeon Mobility M7" rev 0x00
drm0 at radeondrm0
radeondrm0: irq 11
uhci0 at pci0 dev 29 function 0 "Intel 82801DB USB" rev 0x01: irq 11
uhci1 at pci0 dev 29 function 1 "Intel 82801DB USB" rev 0x01: irq 11
uhci2 at pci0 dev 29 function 2 "Intel 82801DB USB" rev 0x01: irq 11
ehci0 at pci0 dev 29 function 7 "Intel 82801DB USB" rev 0x01: irq 11
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 configuration 1 interface 0 "Intel EHCI root hub" rev
2.00/1.00 addr 1 ppb1 at pci0 dev 30 function 0 "Intel 82801BAM
Hub-to-PCI" rev 0x81 pci2 at ppb1 bus 2
2:0:0: mem address conflict 0xb0000000/0x1000
2:0:1: mem address conflict 0xb1000000/0x1000
cbb0 at pci2 dev 0 function 0 "TI PCI1520 CardBus" rev 0x01: irq 11
cbb1 at pci2 dev 0 function 1 "TI PCI1520 CardBus" rev 0x01: irq 11
em0 at pci2 dev 1 function 0 "Intel 82540EP" rev 0x03: irq 11, address
00:16:41:a8:8d:8b ipw0 at pci2 dev 2 function 0 "Intel PRO/Wireless
2100" rev 0x04: irq 11, address 00:04:23:61:fe:6c cardslot0 at cbb0
slot 0 flags 0 cardbus0 at cardslot0: bus 3 device 0 cacheline 0x8,
lattimer 0xb0 pcmcia0 at cardslot0
cardslot1 at cbb1 slot 1 flags 0
cardbus1 at cardslot1: bus 6 device 0 cacheline 0x8, lattimer 0xb0
pcmcia1 at cardslot1
ichpcib0 at pci0 dev 31 function 0 "Intel 82801DBM LPC" rev 0x01
pciide0 at pci0 dev 31 function 1 "Intel 82801DBM IDE" rev 0x01: DMA,
channel 0 configured to compatibility, channel 1 configured to
compatibility wd0 at pciide0 channel 0 drive 0: <WDC WD600UE-32KVT0>
wd0: 16-sector PIO, LBA48, 57231MB, 117210240 sectors wd0(pciide0:0:0):
using PIO mode 4, Ultra-DMA mode 5 atapiscsi0 at pciide0 channel 1
drive 0 scsibus1 at atapiscsi0: 2 targets
cd0 at scsibus1 targ 0 lun 0: <MATSHITA, UJDA745 DVD/CDRW, 1.02> ATAPI
5/cdrom removable cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2
ichiic0 at pci0 dev 31 function 3 "Intel 82801DB SMBus" rev 0x01: irq 11
iic0 at ichiic0
spdmem0 at iic0 addr 0x50: 512MB DDR SDRAM non-parity PC2100CL2.5
spdmem1 at iic0 addr 0x51: 512MB DDR SDRAM non-parity PC2700CL2.5
auich0 at pci0 dev 31 function 5 "Intel 82801DB AC97" rev 0x01: irq 11,
ICH4 ac97: codec id 0x41445374 (Analog Devices AD1981B)
ac97: codec features headphone, 20 bit DAC, No 3D Stereo
audio0 at auich0
"Intel 82801DB Modem" rev 0x01 at pci0 dev 31 function 6 not configured
usb1 at uhci0: USB revision 1.0
uhub1 at usb1 configuration 1 interface 0 "Intel UHCI root hub" rev
1.00/1.00 addr 1 usb2 at uhci1: USB revision 1.0
uhub2 at usb2 configuration 1 interface 0 "Intel UHCI root hub" rev
1.00/1.00 addr 1 usb3 at uhci2: USB revision 1.0
uhub3 at usb3 configuration 1 interface 0 "Intel UHCI root hub" rev
1.00/1.00 addr 1 isa0 at ichpcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5 irq 1 irq 12
pckbd0 at pckbc0 (kbd slot)
wskbd0 at pckbd0: console keyboard
pms0 at pckbc0 (aux slot)
wsmouse0 at pms0 mux 0
wsmouse1 at pms0 mux 0
pms0: Synaptics touchpad, firmware 5.9, 0x2c6ab1 0x0
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
uhidev0 at uhub2 port 1 configuration 1 interface 0 "Logitech USB
Receiver" rev 2.00/12.03 addr 2 uhidev0: iclass 3/1
ukbd0 at uhidev0: 8 variable keys, 6 key codes
wskbd1 at ukbd0 mux 1
uhidev1 at uhub2 port 1 configuration 1 interface 1 "Logitech USB
Receiver" rev 2.00/12.03 addr 2 uhidev1: iclass 3/1, 8 report ids
ums0 at uhidev1 reportid 2: 16 buttons, Z and W dir
wsmouse2 at ums0 mux 0
uhid0 at uhidev1 reportid 3: input=4, output=0, feature=0
uhid1 at uhidev1 reportid 4: input=1, output=0, feature=0
uhid2 at uhidev1 reportid 8: input=1, output=0, feature=0
uhidev2 at uhub2 port 1 configuration 1 interface 2 "Logitech USB
Receiver" rev 2.00/12.03 addr 2 uhidev2: iclass 3/0, 33 report ids
uhid3 at uhidev2 reportid 16: input=6, output=6, feature=0
uhid4 at uhidev2 reportid 17: input=19, output=19, feature=0
uhid5 at uhidev2 reportid 32: input=14, output=14, feature=0
uhid6 at uhidev2 reportid 33: input=31, output=31, feature=0
vscsi0 at root
scsibus2 at vscsi0: 256 targets
softraid0 at root
scsibus3 at softraid0: 256 targets
root on wd0a (96ea0dc55ec74d33.a) swap on wd0b dump on wd0b
radeondrm0: 1024x768, 8bpp
wsdisplay0 at radeondrm0 mux 1: console (std, vt100 emulation), using
wskbd0 wskbd1: connecting to wsdisplay0
wsdisplay0: screen 1-5 added (std, vt100 emulation)
Regards,
Richard
