There is a suspicious message
dev/ksyms: Symbol table not valid.
Next it seems that one CPU is offline somehow. ???
chester# sysctl -a | grep -i cpu
kern.ccpu=1948
hw.ncpu=1
hw.cpuspeed=500
hw.ncpufound=2
hw.ncpuonline=1
Regards
Harri
-------------------------------------------------------------------------------------
Looking for valid bootloader image....
Jumping to start of image at address 0xbfc80000
U-Boot 1.1.1 (UBNT Build ID: 4670715-gbd7e2d7) (Build time: May 27 2014 -
11:16:22)
BIST check passed.
UBNT_E100 r1:2, r2:18, f:4/71, serial #: 788A207F2E7E
MPR 13-00318-18
Core clock: 500 MHz, DDR clock: 266 MHz (532 Mhz data rate)
DRAM: 512 MB
Clearing DRAM....... done
Flash: 4 MB
Net: octeth0, octeth1, octeth2
USB: (port 0) scanning bus for devices... 1 USB Devices found
scanning bus for storage devices...
Device 0: Vendor: JetFlash Prod.: Transcend 32GB Rev: 1100
Type: Removable Hard Disk
Capacity: 30128.0 MB = 29.4 GB (61702144 x 512)
0
reading bsd
..............................
6025929 bytes read
ELF file is 64 bit
Allocating memory for ELF segment: addr: 0xffffffff81000000 (adjusted to:
0x1000000), size 0x5b3bd0
Allocated memory for ELF segment: addr: 0xffffffff81000000, size 0x5b3bd0
Processing PHDR 0
Loading 51ffd8 bytes at ffffffff81000000
Clearing 93bf8 bytes at ffffffff8151ffd8
## Loading Linux kernel with entry point: 0xffffffff81000000 ...
Bootloader: Done loading app on coremask: 0x1
bootmem desc 0x24108 version 3.0
avail phys mem 0x0000000000100290 - 0x0000000000fffce0
avail phys mem 0x00000000015b3bd0 - 0x0000000008100000
avail phys mem 0x0000000008100010 - 0x000000000fffdc00
avail phys mem 0x0000000410000000 - 0x000000041ff00000
Total DRAM Size 0x0000000020000000
mem_layout[0] page 0x0000000000000041 -> 0x00000000000003FF
mem_layout[1] page 0x000000000000056D -> 0x0000000000002040
mem_layout[2] page 0x0000000000002041 -> 0x0000000000003FFFInitial setup done,
switching console.
boot_desc->desc_ver:7
boot_desc->desc_size:400
boot_desc->stack_top:0
boot_desc->heap_start:0
boot_desc->heap_end:0
boot_desc->argc:2
boot_desc->flags:0x5
boot_desc->core_mask:0x1
boot_desc->dram_size:512
boot_desc->phy_mem_desc_addr:0
boot_desc->debugger_flag_addr:0xa44
boot_desc->eclock:500000000
boot_desc->boot_info_addr:0x1001f0
boot_info->ver_major:1
boot_info->ver_minor:2
boot_info->stack_top:0
boot_info->heap_start:0
boot_info->heap_end:0
boot_info->boot_desc_addr:0
boot_info->exception_base_addr:0x1000
boot_info->stack_size:0
boot_info->flags:0x5
boot_info->core_mask:0x1
boot_info->dram_size:512
boot_info->phys_mem_desc_addr:0x24108
boot_info->debugger_flags_addr:0
boot_info->eclock:500000000
boot_info->dclock:266000000
boot_info->board_type:20002
boot_info->board_rev_major:2
boot_info->board_rev_minor:18
boot_info->mac_addr_count:3
boot_info->cf_common_addr:0
boot_info->cf_attr_addr:0
boot_info->led_display_addr:0
boot_info->dfaclock:0
boot_info->config_flags:0x8
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2019 OpenBSD. All rights reserved. https://www.OpenBSD.org
OpenBSD 6.5 (GENERIC.MP) #0: Mon Apr 15 07:34:41 UTC 2019
visa@octeon:/usr/src/sys/arch/octeon/compile/GENERIC.MP
real mem = 536870912 (512MB)
avail mem = 523730944 (499MB)
mainbus0 at root: board 20002 rev 2.18
cpu0 at mainbus0: CN50xx CPU rev 0.1 500 MHz, Software FP emulation
cpu0: cache L1-I 32KB 4 way D 16KB 64 way, L2 128KB 8 way
clock0 at mainbus0: int 5
octcrypto0 at mainbus0
iobus0 at mainbus0
simplebus0 at iobus0: "soc"
octciu0 at simplebus0
cn30xxsmi0 at simplebus0
com0 at simplebus0: ns16550a, 64 byte fifo
com0: console
dwctwo0 at iobus0 base 0x1180068000000 irq 56
usb0 at dwctwo0: USB revision 2.0
uhub0 at usb0 configuration 1 interface 0 "Octeon DWC2 root hub" rev 2.00/1.00
addr 1
octrng0 at iobus0 base 0x1400000000000 irq 0
cn30xxgmx0 at iobus0 base 0x1180008000000
cnmac0 at cn30xxgmx0: RGMII, address 78:8a:20:7f:2e:7e
atphy0 at cnmac0 phy 7: AR8035 10/100/1000 PHY, rev. 2
cnmac1 at cn30xxgmx0: RGMII, address 78:8a:20:7f:2e:7f
atphy1 at cnmac1 phy 6: AR8035 10/100/1000 PHY, rev. 2
cnmac2 at cn30xxgmx0: RGMII, address 78:8a:20:7f:2e:80
atphy2 at cnmac2 phy 5: AR8035 10/100/1000 PHY, rev. 2
/dev/ksyms: Symbol table not valid.
umass0 at uhub0 port 1 configuration 1 interface 0 "JetFlash Mass Storage
Device" rev 2.10/11.00 addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <JetFlash, Transcend 32GB, 1100> SCSI4 0/direct
removable serial.85641000DC26LWBM6WGN
sd0: 30128MB, 512 bytes/sector, 61702144 sectors
vscsi0 at root
scsibus1 at vscsi0: 256 targets
softraid0 at root
scsibus2 at softraid0: 256 targets
boot device: sd0
root on sd0a (5b378c9023bdff5d.a) swap on sd0b dump on sd0b
WARNING: No TOD clock, believing file system.
WARNING: CHECK AND RESET THE DATE!
Automatic boot in progress: starting file system checks.
/dev/sd0a (5b378c9023bdff5d.a): file system is clean; not checking
/dev/sd0e (5b378c9023bdff5d.e): file system is clean; not checking
pf enabled
starting network
cnmac0: no link....
cnmac0: bound to 10.42.100.188 from 10.42.100.2 (80:ee:73:95:c1:0d)
reordering libraries: done.
starting early daemons: syslogd pflogd ntpd.
starting RPC daemons:.
savecore: /bsd: kvm_read: version misread
checking quotas: done.
kvm_mkdb: can't open /dev/ksyms
clearing /tmp
kern.securelevel: 0 -> 1
creating runtime link editor directory cache.
preserving editor files.
starting network daemons: sshd smtpd sndiod.
starting local daemons: cron.
Thu Apr 25 17:59:44 CEST 2019
OpenBSD/octeon (chester.afaics.de) (console)
login:
