Hi, Unable to boot with the following message
open /pci@83,4000/FJSV,ulsa@2,1/disk@0,0:a/etc/random.seed: Invalid argument open /pci@83,4000/FJSV,ulsa@2,1/disk@0,0:a/bsd: Invalid argument Not sure the issue with softraid setup detailed below. Any assistance highly appreciated. Thanks and regards, Kihaguru. {0} ok boot cdrom Resetting ... Sep 02 08:57:03 GMT 2019 XSCF:I::[02030100] Start reset sequence Sep 02 08:57:04 GMT 2019 XSCF:I::[02030200] Reset released... Sep 02 08:57:07 GMT 2019 PowerOn SelfTest start POST:Testing Flash/SRAM POST:Testing SC POST:Testing XSCF POST:Banner POST:FATAL check POST:Testing Timer1 POST:Testing Tick POST:Testing MMU POST:Testing CPU Type POST:Testing DTAG POST:Memory Probe POST:Testing Memory POST:Testing Softint POST:Testing U2P POST:Testing Slave Device POST:Testing Master Device POST:System Configure POST:OBP Start screen not found. keyboard not found. Keyboard not present. Using ttya for input and output. Fujitsu Siemens PRIMEPOWER250 2x SPARC64 V, No Keyboard OpenBoot 3.18.1-1, 16384 MB memory installed Ethernet address 0:b:5d:f3:a7:5c, Host ID: 80f2a75c. XSCF Version: 4.12.1 Executing last command: boot cdrom Boot device: /pci@83,4000/ide@d/cdrom@0,0:f File and args: OpenBSD IEEE 1275 Bootblock 1.4 ..>> OpenBSD BOOT 1.12 Trying bsd... open /pci@83,4000/ide@d/cdrom@0,0:f/etc/random.seed: No such file or directory Booting /pci@83,4000/ide@d/cdrom@0,0:f/bsd 4145224@0x1000000+8120@0x13f4048+3255632@0x1c00000+938672@0x1f1ad50 symbols @ 0xfeae4340 139 start=0x1000000 console is /pci@83,4000/isa@7/su@0,3f8 Copyright (c) 1982, 1986, 1989, 1991, 1993 The Regents of the University of California. All rights reserved. Copyright (c) 1995-2019 OpenBSD. All rights reserved. https://www.OpenBSD.org OpenBSD 6.5 (RAMDISK) #156: Sun Apr 14 05:14:17 MDT 2019 dera...@sparc64.openbsd.org:/usr/src/sys/arch/sparc64/compile/RAMDISK real mem = 17179869184 (16384MB) avail mem = 16869081088 (16087MB) mainbus0 at root: Fujitsu Siemens PRIMEPOWER250 2x SPARC64 V cpu0 at mainbus0: FJSV,SPARC64-V (rev 5.1) @ 1979 MHz cpu0: physical 128K instruction (64 b/l), 128K data (64 b/l), 3072K external (64 b/l) "FJSV,SPARC64-V" at mainbus0 not configured psycho0 at mainbus0 addr 0xfffb2000: SUNW,psycho, impl 0, version 4, ign c0 psycho0: bus range 0-0, PCI bus 0 psycho0: dvma map fe000000-ffffffff, STC0 enabled pci0 at psycho0 ebus0 at pci0 dev 1 function 0 "Sun PCIO EBus2" rev 0x01 "FJSV,scfc" at ebus0 addr 210000-210085, 220000-220031, 260000-260001, 270000-28ffff ivec 0x23 not configured "FJSV,flashprom" at ebus0 addr 0-3fffff not configured clock1 at ebus0 addr 250000-251fff: mk48t59 "FJSV,panel" at ebus0 addr 210011-210011 ivec 0x25 not configured ebus1 at pci0 dev 7 function 0 "Acer Labs M1533 ISA" rev 0x00 com0 at ebus1 addr 3f8-3ff ivec 0x2b: ns16550a, 16 byte fifo com0: console com1 at ebus1 addr 2e8-2ef ivec 0x2b: ns16550a, 16 byte fifo hme0 at pci0 dev 1 function 1 "Sun HME" rev 0x01: ivec 0xe1, address 00:0b:5d:f3:a7:5c nsphyter0 at hme0 phy 1: DP83843 10/100 PHY, rev. 0 mpi0 at pci0 dev 2 function 1 "Symbios Logic 53c1030" rev 0x07: ivec 0xe0 mpi0: 0, firmware 1.0.12.0 scsibus0 at mpi0: 16 targets, initiator 7 sd0 at scsibus0 targ 0 lun 0: <FUJITSU, MAT3073N SUN72G, 0602> SCSI2 0/direct fixed serial.FUJITSU_MAT3073N_SUN72G_000506B00RAR_AAN0P5200RAR sd0: 70007MB, 512 bytes/sector, 143374738 sectors sd1 at scsibus0 targ 1 lun 0: <FUJITSU, MAT3073N SUN72G, 0602> SCSI2 0/direct fixed serial.FUJITSU_MAT3073N_SUN72G_000506B00SSL_AAN0P5200SSL sd1: 70007MB, 512 bytes/sector, 143374738 sectors mpi0: target 0 Sync at 160MHz width 16bit offset 127 QAS 1 DT 1 IU 1 mpi0: target 1 Sync at 160MHz width 16bit offset 127 QAS 1 DT 1 IU 1 pciide0 at pci0 dev 13 function 0 "Acer Labs M5229 UDMA IDE" rev 0xc4: DMA, channel 0 configured to native-PCI, channel 1 configured to native-PCI pciide0: using ivec 0xe4 for native-PCI interrupt atapiscsi0 at pciide0 channel 0 drive 0 scsibus1 at atapiscsi0: 2 targets cd0 at scsibus1 targ 0 lun 0: <MATSHITA, DVD-ROM SR-8178, PY28> ATAPI 5/cdrom removable cd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2 pciide0: channel 1 disabled (no drives) ohci0 at pci0 dev 10 function 0 "Acer Labs M5237 USB" rev 0x03: ivec 0xe9, version 1.0, legacy support usb0 at ohci0: USB revision 1.0 uhub0 at usb0 configuration 1 interface 0 "Acer Labs OHCI root hub" rev 1.00/1.00 addr 1 psycho1 at mainbus0 addr 0xfff9e000: SUNW,psycho, impl 0, version 4, ign c0 psycho1: bus range 128-128, PCI bus 128 psycho1: dvma map fe000000-ffffffff, STC0 enabled, STC1 enabled pci1 at psycho1 bge0 at pci1 dev 1 function 0 "Fujitsu PRIMEPOWER250/450 LAN" rev 0x02, BCM5702/5703 A2 (0x1002): ivec 0xc0, address 00:0b:5d:f4:27:5c brgphy0 at bge0 phy 1: BCM5703 10/100/1000baseT PHY, rev. 2 timer0 at mainbus0 addr 0xfff8bc00 ivec 0xec, 0xed softraid0 at root scsibus2 at softraid0: 256 targets bootpath: /pci@83,4000/ide@d,0/cdrom@0,0:f root on rd0a swap on rd0b dump on rd0b erase ^?, werase ^W, kill ^U, intr ^C, status ^T Welcome to the OpenBSD/sparc64 6.5 installation program. (I)nstall, (U)pgrade, (A)utoinstall or (S)hell? I At any prompt except password prompts you can escape to a shell by typing '!'. Default answers are shown in []'s and are selected by pressing RETURN. You can exit this program at any time by pressing Control-C, but this can leave your system in an inconsistent state. Terminal type? [sun] ~ ~ ~ ~ Available disks are: sd0 sd1. Which disk is the root disk? ('?' for details) [sd0] ! Type 'exit' to return to install. www# dd if=/dev/urandom of=/dev/rsd0c bs=1m dd: /dev/rsd0c: short write on character device dd: /dev/rsd0c: end of device 70008+0 records in 70007+1 records out 73407865856 bytes transferred in 2026.673 secs (36220859 bytes/sec) www# dd if=/dev/urandom of=/dev/rsd1c bs=1m dd: /dev/rsd1c: short write on character device dd: /dev/rsd1c: end of device 70008+0 records in 70007+1 records out 73407865856 bytes transferred in 2029.361 secs (36172892 bytes/sec) www# cd /dev www# ls MAKEDEV rd0c rsd1d rsd2n rwd1g sd0a sd1k urandom wd1j bio rfd0a rsd1e rsd2o rwd1h sd0b sd1l wd0a wd1k bpf rfd0b rsd1f rsd2p rwd1i sd0c sd1m wd0b wd1l bpf0 rfd0c rsd1g rst0 rwd1j sd0d sd1n wd0c wd1m cd0a rfd0i rsd1h rwd0a rwd1k sd0e sd1o wd0d wd1n cd0c rrd0a rsd1i rwd0b rwd1l sd0f sd1p wd0e wd1o console rrd0c rsd1j rwd0c rwd1m sd0g sd2a wd0f wd1p diskmap rsd0a rsd1k rwd0d rwd1n sd0h sd2b wd0g wd2a enrst0 rsd0b rsd1l rwd0e rwd1o sd0i sd2c wd0h wd2b erst0 rsd0c rsd1m rwd0f rwd1p sd0j sd2d wd0i wd2c fd0a rsd0d rsd1n rwd0g rwd2a sd0k sd2e wd0j wd2d fd0b rsd0e rsd1o rwd0h rwd2b sd0l sd2f wd0k wd2e fd0c rsd0f rsd1p rwd0i rwd2c sd0m sd2g wd0l wd2f fd0i rsd0g rsd2a rwd0j rwd2d sd0n sd2h wd0m wd2g klog rsd0h rsd2b rwd0k rwd2e sd0o sd2i wd0n wd2h kmem rsd0i rsd2c rwd0l rwd2f sd0p sd2j wd0o wd2i ksyms rsd0j rsd2d rwd0m rwd2g sd1a sd2k wd0p wd2j mdesc rsd0k rsd2e rwd0n rwd2h sd1b sd2l wd1a wd2k mem rsd0l rsd2f rwd0o rwd2i sd1c sd2m wd1b wd2l nrst0 rsd0m rsd2g rwd0p rwd2j sd1d sd2n wd1c wd2m null rsd0n rsd2h rwd1a rwd2k sd1e sd2o wd1d wd2n openprom rsd0o rsd2i rwd1b rwd2l sd1f sd2p wd1e wd2o random rsd0p rsd2j rwd1c rwd2m sd1g stderr wd1f wd2p rcd0a rsd1a rsd2k rwd1d rwd2n sd1h stdin wd1g zero rcd0c rsd1b rsd2l rwd1e rwd2o sd1i stdout wd1h rd0a rsd1c rsd2m rwd1f rwd2p sd1j tty wd1i www# disklabel -E sd0 This platform requires that partition offsets/sizes be on cylinder boundaries. Partition offsets/sizes will be rounded to the nearest cylinder automatically. Label editor (enter '?' for help at any prompt) sd0> p OpenBSD area: 0-143374738; size: 143374738; free: 143374738 # size offset fstype [fsize bsize cpg] c: 143374738 0 unused sd0> q No label changes. www# disklabel -E sd1 This platform requires that partition offsets/sizes be on cylinder boundaries. Partition offsets/sizes will be rounded to the nearest cylinder automatically. Label editor (enter '?' for help at any prompt) sd1> p OpenBSD area: 0-143374738; size: 143374738; free: 143374738 # size offset fstype [fsize bsize cpg] c: 143374738 0 unused sd1> q No label changes. www# disklabel -E sd2 disklabel: /dev/rsd2c: Device not configured www# fdisk -iy sd0 sh: fdisk: not found www# disklabel -E sd0 This platform requires that partition offsets/sizes be on cylinder boundaries. Partition offsets/sizes will be rounded to the nearest cylinder automatically. Label editor (enter '?' for help at any prompt) sd0> a partition: [a] offset: [0] size: [143374738] * FS type: [4.2BSD] RAID sd0> w sd0> q No label changes. www# disklabel sd0 > layout www# disklabel -R sd1 layout www# rm layout www# bioctl -c 1 -l sd0a,sd1a softraid0 sd2 at scsibus2 targ 1 lun 0: <OPENBSD, SR RAID 1, 006> SCSI2 0/direct fixed sd2: 70002MB, 512 bytes/sector, 143366016 sectors softraid0: RAID 1 volume attached as sd2 www# dd if=/dev/zero of=/dev/rsd2c bs=1m count=1 1+0 records in 1+0 records out 1048576 bytes transferred in 0.033 secs (31058796 bytes/sec) www# bioctl sd2 Volume Status Size Device softraid0 0 Online 73403400192 sd2 RAID1 0 Online 73403400192 0:0.0 noencl <sd0a> 1 Online 73403400192 0:1.0 noencl <sd1a> www# exit Available disks are: sd0 sd1 sd2. Which disk is the root disk? ('?' for details) [sd0] sd2 The auto-allocated layout for sd2 is: # size offset fstype [fsize bsize cpg] a: 1.0G 0 4.2BSD 2048 16384 1 # / b: 5.9G 2104515 swap c: 68.4G 0 unused d: 4.0G 14442435 4.2BSD 2048 16384 1 # /tmp e: 7.6G 22844430 4.2BSD 2048 16384 1 # /var f: 2.0G 38829105 4.2BSD 2048 16384 1 # /usr g: 1.0G 43038135 4.2BSD 2048 16384 1 # /usr/X11R6 h: 9.7G 45142650 4.2BSD 2048 16384 1 # /usr/local i: 2.0G 65497005 4.2BSD 2048 16384 1 # /usr/src j: 6.0G 69706035 4.2BSD 2048 16384 1 # /usr/obj k: 29.1G 82300995 4.2BSD 2048 16384 1 # /home Use (A)uto layout, (E)dit auto layout, or create (C)ustom layout? [a] /dev/rsd2a: 1027.6MB in 2104512 sectors of 512 bytes 6 cylinder groups of 202.47MB, 12958 blocks, 25984 inodes each /dev/rsd2k: 29815.9MB in 61063064 sectors of 512 bytes 148 cylinder groups of 202.47MB, 12958 blocks, 25984 inodes each /dev/rsd2d: 4102.5MB in 8401992 sectors of 512 bytes 21 cylinder groups of 202.47MB, 12958 blocks, 25984 inodes each /dev/rsd2f: 2055.2MB in 4209028 sectors of 512 bytes 11 cylinder groups of 202.47MB, 12958 blocks, 25984 inodes each /dev/rsd2g: 1027.6MB in 2104512 sectors of 512 bytes 6 cylinder groups of 202.47MB, 12958 blocks, 25984 inodes each /dev/rsd2h: 9938.6MB in 20354352 sectors of 512 bytes 50 cylinder groups of 202.47MB, 12958 blocks, 25984 inodes each /dev/rsd2j: 6149.9MB in 12594960 sectors of 512 bytes 31 cylinder groups of 202.47MB, 12958 blocks, 25984 inodes each /dev/rsd2i: 2055.2MB in 4209028 sectors of 512 bytes 11 cylinder groups of 202.47MB, 12958 blocks, 25984 inodes each /dev/rsd2e: 7805.0MB in 15984672 sectors of 512 bytes 39 cylinder groups of 202.47MB, 12958 blocks, 25984 inodes each Available disks are: sd0 sd1. Which disk do you wish to initialize? (or 'done') [done] /dev/sd2a (f17019aae84f4ec9.a) on /mnt type ffs (rw, asynchronous, local) /dev/sd2k (f17019aae84f4ec9.k) on /mnt/home type ffs (rw, asynchronous, local, nodev, nosuid) /dev/sd2d (f17019aae84f4ec9.d) on /mnt/tmp type ffs (rw, asynchronous, local, nodev, nosuid) /dev/sd2f (f17019aae84f4ec9.f) on /mnt/usr type ffs (rw, asynchronous, local, nodev) /dev/sd2g (f17019aae84f4ec9.g) on /mnt/usr/X11R6 type ffs (rw, asynchronous, local, nodev) /dev/sd2h (f17019aae84f4ec9.h) on /mnt/usr/local type ffs (rw, asynchronous, local, nodev) /dev/sd2j (f17019aae84f4ec9.j) on /mnt/usr/obj type ffs (rw, asynchronous, local, nodev, nosuid) /dev/sd2i (f17019aae84f4ec9.i) on /mnt/usr/src type ffs (rw, asynchronous, local, nodev, nosuid) /dev/sd2e (f17019aae84f4ec9.e) on /mnt/var type ffs (rw, asynchronous, local, nodev, nosuid) Let's install the sets! Location of sets? (cd0 disk http or 'done') [http] HTTP proxy URL? (e.g. 'http://proxy:8080', or 'none') [none] HTTP Server? (hostname, list#, 'done' or '?') [ftp.OpenBSD.org] Server directory? [pub/OpenBSD/6.5/sparc64] Select sets by entering a set name, a file name pattern or 'all'. De-select sets by prepending a '-', e.g.: '-game*'. Selected sets are labelled '[X]'. [X] bsd [X] base65.tgz [X] game65.tgz [X] xfont65.tgz [X] bsd.mp [X] comp65.tgz [X] xbase65.tgz [X] xserv65.tgz [X] bsd.rd [X] man65.tgz [X] xshare65.tgz Set name(s)? (or 'abort' or 'done') [done] -game* -x* [X] bsd [X] base65.tgz [ ] game65.tgz [ ] xfont65.tgz [X] bsd.mp [X] comp65.tgz [ ] xbase65.tgz [ ] xserv65.tgz [X] bsd.rd [X] man65.tgz [ ] xshare65.tgz Set name(s)? (or 'abort' or 'done') [done] Get/Verify SHA256.sig 100% |**************************| 1974 00:00 Signature Verified Get/Verify bsd 100% |**************************| 11005 KB 00:14 Get/Verify bsd.mp 100% |**************************| 11076 KB 00:14 Get/Verify bsd.rd 100% |**************************| 2699 KB 00:09 Get/Verify base65.tgz 100% |**************************| 160 MB 01:41 Get/Verify comp65.tgz 100% |**************************| 68832 KB 01:39 Get/Verify man65.tgz 100% |**************************| 7392 KB 00:12 Installing bsd 100% |**************************| 11005 KB 00:00 Installing bsd.mp 100% |**************************| 11076 KB 00:00 Installing bsd.rd 100% |**************************| 2699 KB 00:00 Installing base65.tgz 100% |**************************| 160 MB 00:15 Extracting etc.tgz 100% |**************************| 260 KB 00:00 Installing comp65.tgz 100% |**************************| 68832 KB 00:09 Installing man65.tgz 100% |**************************| 7392 KB 00:01 Location of sets? (cd0 disk http or 'done') [done] Saving configuration files... done. Making all device nodes... done. Multiprocessor machine; using bsd.mp instead of bsd. Relinking to create unique kernel... done. CONGRATULATIONS! Your OpenBSD install has been successfully completed! When you login to your new system the first time, please read your mail using the 'mail' command. Exit to (S)hell, (H)alt or (R)eboot? [halt] R syncing disks... done rebooting Resetting ... Sep 02 13:11:10 GMT 2019 XSCF:I::[02030100] Start reset sequence Sep 02 13:11:10 GMT 2019 XSCF:I::[02030200] Reset released... Sep 02 13:11:13 GMT 2019 PowerOn SelfTest start POST:Testing Flash/SRAM POST:Testing SC POST:Testing XSCF POST:Banner POST:FATAL check POST:Testing Timer1 POST:Testing Tick POST:Testing MMU POST:Testing CPU Type POST:Testing DTAG POST:Memory Probe POST:Testing Memory POST:Testing Softint POST:Testing U2P POST:Testing Slave Device POST:Testing Master Device POST:System Configure POST:OBP Start screen not found. keyboard not found. Keyboard not present. Using ttya for input and output. Fujitsu Siemens PRIMEPOWER250 2x SPARC64 V, No Keyboard OpenBoot 3.18.1-1, 16384 MB memory installed Ethernet address 0:b:5d:f3:a7:5c, Host ID: 80f2a75c. XSCF Version: 4.12.1 Executing last command: boot Boot device: /pci@83,4000/FJSV,ulsa@2,1/disk@0,0 File and args: OpenBSD IEEE 1275 Bootblock 1.4 >> OpenBSD BOOT 1.12 Can't read disk label. Can't open disk label package sr0* Trying bsd... open /pci@83,4000/FJSV,ulsa@2,1/disk@0,0:a/etc/random.seed: Invalid argument open /pci@83,4000/FJSV,ulsa@2,1/disk@0,0:a/bsd: Invalid argument Boot: