On Mon, Aug 28, 2023 at 07:41:19AM +0200, Otto Moerbeek wrote:
> On Sun, Aug 27, 2023 at 08:40:44PM -0400, Christopher Sean Hilton wrote:
>
[ ...snip... ]
> > I can solve my problems in one of two ways. If I can boot with serial
> > consoles by setting them up in /etc/boot.conf and also have terminals
> > on the pc consoles, I'd be happy. I'd also be happy if I could figure
> > out how to configure the BIOS to make enable the serial port as just
> > a plain serial port. Super Micro seems to have other ideas and I
> > understand that this is *my* problem.
> >
> > I'll tak any suggestions here.
>
> What did you put into /etc/ttys when using a VGA console?
>
> -Otto
>
I've moved it to the serial console config. Admitting in advance that
I could be mistaken, I've posted the relevant files below. I annotated
the dmesg output with marks to show where the serial port is detected
and that the wsdisplay *does not attach* to the detected vga1
device. I think that if I could make the wsdisplay device attach then
my problem would be solved.
Thanks again
-- Chris
Attached output follows:
== /etc/boot.conf ==
stty com0 115200
set tty com0
== /etc/ttys ==
#
# $OpenBSD: ttys,v 1.2 2008/01/09 17:39:42 miod Exp $
#
# name getty type status comments
#
console "/usr/libexec/getty std.9600" vt220 off secure
ttyC0 "/usr/libexec/getty std.9600" vt220 on secure
ttyC1 "/usr/libexec/getty std.9600" vt220 on secure
ttyC2 "/usr/libexec/getty std.9600" vt220 on secure
ttyC3 "/usr/libexec/getty std.9600" vt220 on secure
ttyC4 "/usr/libexec/getty std.9600" vt220 off secure
ttyC5 "/usr/libexec/getty std.9600" vt220 on secure
ttyC6 "/usr/libexec/getty std.9600" vt220 off secure
ttyC7 "/usr/libexec/getty std.9600" vt220 off secure
ttyC8 "/usr/libexec/getty std.9600" vt220 off secure
ttyC9 "/usr/libexec/getty std.9600" vt220 off secure
ttyCa "/usr/libexec/getty std.9600" vt220 off secure
ttyCb "/usr/libexec/getty std.9600" vt220 off secure
tty00 "/usr/libexec/getty std.115200" unknown on secure
tty01 "/usr/libexec/getty std.115200" unknown on secure
tty02 "/usr/libexec/getty std.9600" unknown off
tty03 "/usr/libexec/getty std.9600" unknown off
tty04 "/usr/libexec/getty std.9600" unknown off
tty05 "/usr/libexec/getty std.9600" unknown off
tty06 "/usr/libexec/getty std.9600" unknown off
tty07 "/usr/libexec/getty std.9600" unknown off
...
== dmesg.boot ==
OpenBSD 7.3 (GENERIC.MP) #3: Tue Jul 25 08:20:26 MDT 2023
[email protected]:/usr/src/sys/arch/amd64/compile/GENERIC.MP
real mem = 8541495296 (8145MB)
avail mem = 8263225344 (7880MB)
random: good seed from bootblocks
mpath0 at root
scsibus0 at mpath0: 256 targets
mainbus0 at root
bios0 at mainbus0: SMBIOS rev. 2.8 @ 0x7f4d8000 (50 entries)
bios0: vendor American Megatrends Inc. version "2.1" date 01/18/2018
bios0: Supermicro A1SRi-2758F
acpi0 at bios0: ACPI 5.0
acpi0: sleep states S0 S5
acpi0: tables DSDT FACP FPDT FIDT SPMI MCFG WDAT UEFI APIC BDAT HPET SSDT
SPCR HEST BERT ERST EINJ
acpi0: wakeup devices PEX1(S0) PEX2(S0) PEX3(S0) PEX4(S0) EHC1(S0)
acpitimer0 at acpi0: 3579545 Hz, 24 bits
acpimcfg0 at acpi0
acpimcfg0: addr 0xe0000000, bus 0-255
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: Intel(R) Atom(TM) CPU C2758 @ 2.40GHz, 2400.37 MHz, 06-4d-08
cpu0:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,
cpu0: 24KB 64b/line 6-way D-cache, 32KB 64b/line 8-way I-cache, 1MB
64b/line 16-way L2 cache
cpu0: smt 0, core 0, package 0
mtrr: Pentium Pro MTRR support, 8 var ranges, 88 fixed ranges
cpu0: apic clock running at 100MHz
cpu0: mwait min=64, max=64, C-substates=0.2.0.0.0.0.3, IBE
cpu1 at mainbus0: apid 2 (application processor)
cpu1: Intel(R) Atom(TM) CPU C2758 @ 2.40GHz, 2400.66 MHz, 06-4d-08
cpu1:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,
cpu1: 24KB 64b/line 6-way D-cache, 32KB 64b/line 8-way I-cache, 1MB
64b/line 16-way L2 cache
cpu1: smt 0, core 1, package 0
...
cpu7 at mainbus0: apid 14 (application processor)
cpu7: Intel(R) Atom(TM) CPU C2758 @ 2.40GHz, 2402.94 MHz, 06-4d-08
cpu7:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,
cpu7: 24KB 64b/line 6-way D-cache, 32KB 64b/line 8-way I-cache, 1MB
64b/line 16-way L2 cache
cpu7: smt 0, core 7, package 0
ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 20, 24 pins
acpihpet0 at acpi0: 14318179 Hz
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus 1 (PEX1)
acpiprt2 at acpi0: bus 2 (BR04)
acpiprt3 at acpi0: bus 3 (PEX2)
acpiprt4 at acpi0: bus 4 (PEX3)
acpiprt5 at acpi0: bus -1 (PEX4)
acpipci0 at acpi0 PCI0: 0x00000010 0x00000011 0x00000000
"PNP0003" at acpi0 not configured
acpicmos0 at acpi0
(1)->com0 at acpi0 UAR1 addr 0x3f8/0x8 irq 4: ns16550a, 16 byte fifo
+>com0: console
com1 at acpi0 UAR2 addr 0x2f8/0x8 irq 3: ns16550a, 16 byte fifo
"IPI0001" at acpi0 not configured
"PNP0C33" at acpi0 not configured
acpicpu0 at acpi0: C2(350@41 mwait.3@0x51), C1(1000@1 mwait.1), PSS
acpicpu1 at acpi0: C2(350@41 mwait.3@0x51), C1(1000@1 mwait.1), PSS
acpicpu2 at acpi0: C2(350@41 mwait.3@0x51), C1(1000@1 mwait.1), PSS
acpicpu3 at acpi0: C2(350@41 mwait.3@0x51), C1(1000@1 mwait.1), PSS
acpicpu4 at acpi0: C2(350@41 mwait.3@0x51), C1(1000@1 mwait.1), PSS
acpicpu5 at acpi0: C2(350@41 mwait.3@0x51), C1(1000@1 mwait.1), PSS
acpicpu6 at acpi0: C2(350@41 mwait.3@0x51), C1(1000@1 mwait.1), PSS
acpicpu7 at acpi0: C2(350@41 mwait.3@0x51), C1(1000@1 mwait.1), PSS
ipmi at mainbus0 not configured
cpu0: using VERW MDS workaround
cpu0: Enhanced SpeedStep 2400 MHz: speeds: 2400, 2300, 2200, 2100, 2000,
1900, 1800, 1700, 1600, 1500, 1400, 1300, 1200 MHz
pci0 at mainbus0 bus 0
pchb0 at pci0 dev 0 function 0 "Intel Atom C2000 Host" rev 0x03
ppb0 at pci0 dev 1 function 0 "Intel Atom C2000 PCIE" rev 0x03: msi
pci1 at ppb0 bus 1
ppb1 at pci1 dev 0 function 0 "ASPEED Technology AST1150 PCI" rev 0x03
pci2 at ppb1 bus 2
(2)->vga1 at pci2 dev 0 function 0 "ASPEED Technology AST2000" rev 0x30
+>wsdisplay at vga1 not configured
ppb2 at pci0 dev 2 function 0 "Intel Atom C2000 PCIE" rev 0x03: msi
pci3 at ppb2 bus 3
xhci0 at pci3 dev 0 function 0 "Renesas uPD720201 xHCI" rev 0x03: msi,
xHCI 1.0
usb0 at xhci0: USB revision 3.0
uhub0 at usb0 configuration 1 interface 0 "Renesas xHCI root hub" rev
3.00/1.00 addr 1
ppb3 at pci0 dev 3 function 0 "Intel Atom C2000 PCIE" rev 0x03: msi
pci4 at ppb3 bus 4
ix0 at pci4 dev 0 function 0 "Intel X540T" rev 0x01, msix, 8 queues,
address b4:96:91:9f:04:80
ix1 at pci4 dev 0 function 1 "Intel X540T" rev 0x01, msix, 8 queues,
address b4:96:91:9f:04:82
vendor "Intel", unknown product 0x1f18 (class processor subclass
Co-processor, rev 0x03) at pci0 dev 11 function 0 not configured
pchb1 at pci0 dev 14 function 0 "Intel Atom C2000 RAS" rev 0x03
"Intel Atom C2000 RCEC" rev 0x03 at pci0 dev 15 function 0 not configured
"Intel Atom C2000 SMBus" rev 0x03 at pci0 dev 19 function 0 not configured
em0 at pci0 dev 20 function 0 "Intel I354 SGMII" rev 0x03: msi, address
ac:1f:6b:b1:d2:08
em1 at pci0 dev 20 function 1 "Intel I354 SGMII" rev 0x03: msi, address
ac:1f:6b:b1:d2:09
em2 at pci0 dev 20 function 2 "Intel I354 SGMII" rev 0x03: msi, address
ac:1f:6b:b1:d2:0a
em3 at pci0 dev 20 function 3 "Intel I354 SGMII" rev 0x03: msi, address
ac:1f:6b:b1:d2:0b
ehci0 at pci0 dev 22 function 0 "Intel Atom C2000 USB" rev 0x03: apic 2
int 23
usb1 at ehci0: USB revision 2.0
uhub1 at usb1 configuration 1 interface 0 "Intel EHCI root hub" rev
2.00/1.00 addr 1
ahci0 at pci0 dev 23 function 0 "Intel Atom C2000 AHCI" rev 0x03: msi,
AHCI 1.3
scsibus1 at ahci0: 32 targets
ahci1 at pci0 dev 24 function 0 "Intel Atom C2000 AHCI" rev 0x03: msi,
AHCI 1.3
ahci1: port 0: 6.0Gb/s
scsibus2 at ahci1: 32 targets
sd0 at scsibus2 targ 0 lun 0: <ATA, PNY CS900 120GB, CS90>
naa.5f8db4c151800400
sd0: 114473MB, 512 bytes/sector, 234441648 sectors, thin
pcib0 at pci0 dev 31 function 0 "Intel Atom C2000 PCU" rev 0x03
ichiic0 at pci0 dev 31 function 3 "Intel Atom C2000 PCU SMBus" rev 0x03:
apic 2 int 18
iic0 at ichiic0
sdtemp0 at iic0 addr 0x18: stts2004
iic0: addr 0x2e 00=42 words 00=4242 01=0000 02=0000 03=0000 04=0000
05=0000 06=0000 07=0000
spdmem0 at iic0 addr 0x50: 8GB DDR3 SDRAM ECC PC3-12800 with thermal sensor
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5 irq 1 irq 12
pckbd0 at pckbc0 (kbd slot)
wskbd0 at pckbd0 mux 1
pms0 at pckbc0 (aux slot)
wsmouse0 at pms0 mux 0
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
vmm0 at mainbus0: VMX/EPT (using slow L1TF mitigation)
uhub2 at uhub1 port 1 configuration 1 interface 0 "Intel product 0x07db"
rev 2.00/0.03 addr 2
uhub3 at uhub2 port 1 configuration 1 interface 0 "Terminus Technology USB
2.0 Hub" rev 2.00/1.11 addr 3
uhub4 at uhub2 port 3 configuration 1 interface 0 "ATEN International
product 0x7000" rev 2.00/0.00 addr 4
uhidev0 at uhub4 port 1 configuration 1 interface 0 "ATEN International
product 0x2419" rev 1.10/1.00 addr 5
uhidev0: iclass 3/1
ukbd0 at uhidev0: 8 variable keys, 6 key codes
wskbd1 at ukbd0 mux 1
uhidev1 at uhub4 port 1 configuration 1 interface 1 "ATEN International
product 0x2419" rev 1.10/1.00 addr 5
uhidev1: iclass 3/1
ums0 at uhidev1: 3 buttons, Z dir
wsmouse1 at ums0 mux 0
vscsi0 at root
scsibus3 at vscsi0: 256 targets
softraid0 at root
scsibus4 at softraid0: 256 targets
root on sd0a (070da3f4af65d174.a) swap on sd0b dump on sd0b
--
Chris
__o "All I was trying to do was get home from work."
_`\<,_ -Rosa Parks
___(*)/_(*)____.___o____..___..o...________ooO..._____________________
Christopher Sean Hilton [chris/at/vindaloo/dot/com]
