On Mon, Aug 28, 2023 at 10:33:23AM -0400, Christopher Sean Hilton wrote:
> On Mon, Aug 28, 2023 at 07:41:19AM +0200, Otto Moerbeek wrote:
> > On Sun, Aug 27, 2023 at 08:40:44PM -0400, Christopher Sean Hilton wrote:
> >
>
> [ ...snip... ]
>
> > > I can solve my problems in one of two ways. If I can boot with serial
> > > consoles by setting them up in /etc/boot.conf and also have terminals
> > > on the pc consoles, I'd be happy. I'd also be happy if I could figure
> > > out how to configure the BIOS to make enable the serial port as just
> > > a plain serial port. Super Micro seems to have other ideas and I
> > > understand that this is *my* problem.
> > >
> > > I'll tak any suggestions here.
> >
> > What did you put into /etc/ttys when using a VGA console?
> >
> > -Otto
> >
>
> I've moved it to the serial console config. Admitting in advance that
> I could be mistaken, I've posted the relevant files below. I annotated
> the dmesg output with marks to show where the serial port is detected
> and that the wsdisplay *does not attach* to the detected vga1
> device. I think that if I could make the wsdisplay device attach then
> my problem would be solved.
Having wsdisplay(4) without being the under;ying device being marked
as console is atypical. Don't know if it is possible at all.
>
> Thanks again
>
> -- Chris
>
> Attached output follows:
>
>
> == /etc/boot.conf ==
>
> stty com0 115200
> set tty com0
>
>
> == /etc/ttys ==
>
> #
> # $OpenBSD: ttys,v 1.2 2008/01/09 17:39:42 miod Exp $
> #
> # name getty type status comments
> #
> console "/usr/libexec/getty std.9600" vt220 off secure
> ttyC0 "/usr/libexec/getty std.9600" vt220 on secure
> ttyC1 "/usr/libexec/getty std.9600" vt220 on secure
> ttyC2 "/usr/libexec/getty std.9600" vt220 on secure
> ttyC3 "/usr/libexec/getty std.9600" vt220 on secure
> ttyC4 "/usr/libexec/getty std.9600" vt220 off secure
> ttyC5 "/usr/libexec/getty std.9600" vt220 on secure
> ttyC6 "/usr/libexec/getty std.9600" vt220 off secure
> ttyC7 "/usr/libexec/getty std.9600" vt220 off secure
> ttyC8 "/usr/libexec/getty std.9600" vt220 off secure
> ttyC9 "/usr/libexec/getty std.9600" vt220 off secure
> ttyCa "/usr/libexec/getty std.9600" vt220 off secure
> ttyCb "/usr/libexec/getty std.9600" vt220 off secure
> tty00 "/usr/libexec/getty std.115200" unknown on secure
might need to play with "local" and/or "softcar" (I always forget
which does what) when using a vga console to get a login prompt on tty00
See ttys(5).
-Otto
> tty01 "/usr/libexec/getty std.115200" unknown on secure
> tty02 "/usr/libexec/getty std.9600" unknown off
> tty03 "/usr/libexec/getty std.9600" unknown off
> tty04 "/usr/libexec/getty std.9600" unknown off
> tty05 "/usr/libexec/getty std.9600" unknown off
> tty06 "/usr/libexec/getty std.9600" unknown off
> tty07 "/usr/libexec/getty std.9600" unknown off
> ...
>
>
> == dmesg.boot ==
>
> OpenBSD 7.3 (GENERIC.MP) #3: Tue Jul 25 08:20:26 MDT 2023
>
> [email protected]:/usr/src/sys/arch/amd64/compile/GENERIC.MP
> real mem = 8541495296 (8145MB)
> avail mem = 8263225344 (7880MB)
> random: good seed from bootblocks
> mpath0 at root
> scsibus0 at mpath0: 256 targets
> mainbus0 at root
> bios0 at mainbus0: SMBIOS rev. 2.8 @ 0x7f4d8000 (50 entries)
> bios0: vendor American Megatrends Inc. version "2.1" date 01/18/2018
> bios0: Supermicro A1SRi-2758F
> acpi0 at bios0: ACPI 5.0
> acpi0: sleep states S0 S5
> acpi0: tables DSDT FACP FPDT FIDT SPMI MCFG WDAT UEFI APIC BDAT HPET
> SSDT SPCR HEST BERT ERST EINJ
> acpi0: wakeup devices PEX1(S0) PEX2(S0) PEX3(S0) PEX4(S0) EHC1(S0)
> acpitimer0 at acpi0: 3579545 Hz, 24 bits
> acpimcfg0 at acpi0
> acpimcfg0: addr 0xe0000000, bus 0-255
> acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
> cpu0 at mainbus0: apid 0 (boot processor)
> cpu0: Intel(R) Atom(TM) CPU C2758 @ 2.40GHz, 2400.37 MHz, 06-4d-08
> cpu0:
> FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,
> cpu0: 24KB 64b/line 6-way D-cache, 32KB 64b/line 8-way I-cache, 1MB
> 64b/line 16-way L2 cache
> cpu0: smt 0, core 0, package 0
> mtrr: Pentium Pro MTRR support, 8 var ranges, 88 fixed ranges
> cpu0: apic clock running at 100MHz
> cpu0: mwait min=64, max=64, C-substates=0.2.0.0.0.0.3, IBE
> cpu1 at mainbus0: apid 2 (application processor)
> cpu1: Intel(R) Atom(TM) CPU C2758 @ 2.40GHz, 2400.66 MHz, 06-4d-08
> cpu1:
> FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,
> cpu1: 24KB 64b/line 6-way D-cache, 32KB 64b/line 8-way I-cache, 1MB
> 64b/line 16-way L2 cache
> cpu1: smt 0, core 1, package 0
>
> ...
>
> cpu7 at mainbus0: apid 14 (application processor)
> cpu7: Intel(R) Atom(TM) CPU C2758 @ 2.40GHz, 2402.94 MHz, 06-4d-08
> cpu7:
> FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,
> cpu7: 24KB 64b/line 6-way D-cache, 32KB 64b/line 8-way I-cache, 1MB
> 64b/line 16-way L2 cache
> cpu7: smt 0, core 7, package 0
> ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 20, 24 pins
> acpihpet0 at acpi0: 14318179 Hz
> acpiprt0 at acpi0: bus 0 (PCI0)
> acpiprt1 at acpi0: bus 1 (PEX1)
> acpiprt2 at acpi0: bus 2 (BR04)
> acpiprt3 at acpi0: bus 3 (PEX2)
> acpiprt4 at acpi0: bus 4 (PEX3)
> acpiprt5 at acpi0: bus -1 (PEX4)
> acpipci0 at acpi0 PCI0: 0x00000010 0x00000011 0x00000000
> "PNP0003" at acpi0 not configured
> acpicmos0 at acpi0
> (1)->com0 at acpi0 UAR1 addr 0x3f8/0x8 irq 4: ns16550a, 16 byte fifo
> +>com0: console
> com1 at acpi0 UAR2 addr 0x2f8/0x8 irq 3: ns16550a, 16 byte fifo
> "IPI0001" at acpi0 not configured
> "PNP0C33" at acpi0 not configured
> acpicpu0 at acpi0: C2(350@41 mwait.3@0x51), C1(1000@1 mwait.1), PSS
> acpicpu1 at acpi0: C2(350@41 mwait.3@0x51), C1(1000@1 mwait.1), PSS
> acpicpu2 at acpi0: C2(350@41 mwait.3@0x51), C1(1000@1 mwait.1), PSS
> acpicpu3 at acpi0: C2(350@41 mwait.3@0x51), C1(1000@1 mwait.1), PSS
> acpicpu4 at acpi0: C2(350@41 mwait.3@0x51), C1(1000@1 mwait.1), PSS
> acpicpu5 at acpi0: C2(350@41 mwait.3@0x51), C1(1000@1 mwait.1), PSS
> acpicpu6 at acpi0: C2(350@41 mwait.3@0x51), C1(1000@1 mwait.1), PSS
> acpicpu7 at acpi0: C2(350@41 mwait.3@0x51), C1(1000@1 mwait.1), PSS
> ipmi at mainbus0 not configured
> cpu0: using VERW MDS workaround
> cpu0: Enhanced SpeedStep 2400 MHz: speeds: 2400, 2300, 2200, 2100, 2000,
> 1900, 1800, 1700, 1600, 1500, 1400, 1300, 1200 MHz
> pci0 at mainbus0 bus 0
> pchb0 at pci0 dev 0 function 0 "Intel Atom C2000 Host" rev 0x03
> ppb0 at pci0 dev 1 function 0 "Intel Atom C2000 PCIE" rev 0x03: msi
> pci1 at ppb0 bus 1
> ppb1 at pci1 dev 0 function 0 "ASPEED Technology AST1150 PCI" rev 0x03
> pci2 at ppb1 bus 2
> (2)->vga1 at pci2 dev 0 function 0 "ASPEED Technology AST2000" rev 0x30
> +>wsdisplay at vga1 not configured
> ppb2 at pci0 dev 2 function 0 "Intel Atom C2000 PCIE" rev 0x03: msi
> pci3 at ppb2 bus 3
> xhci0 at pci3 dev 0 function 0 "Renesas uPD720201 xHCI" rev 0x03: msi,
> xHCI 1.0
> usb0 at xhci0: USB revision 3.0
> uhub0 at usb0 configuration 1 interface 0 "Renesas xHCI root hub" rev
> 3.00/1.00 addr 1
> ppb3 at pci0 dev 3 function 0 "Intel Atom C2000 PCIE" rev 0x03: msi
> pci4 at ppb3 bus 4
> ix0 at pci4 dev 0 function 0 "Intel X540T" rev 0x01, msix, 8 queues,
> address b4:96:91:9f:04:80
> ix1 at pci4 dev 0 function 1 "Intel X540T" rev 0x01, msix, 8 queues,
> address b4:96:91:9f:04:82
> vendor "Intel", unknown product 0x1f18 (class processor subclass
> Co-processor, rev 0x03) at pci0 dev 11 function 0 not configured
> pchb1 at pci0 dev 14 function 0 "Intel Atom C2000 RAS" rev 0x03
> "Intel Atom C2000 RCEC" rev 0x03 at pci0 dev 15 function 0 not configured
> "Intel Atom C2000 SMBus" rev 0x03 at pci0 dev 19 function 0 not
> configured
> em0 at pci0 dev 20 function 0 "Intel I354 SGMII" rev 0x03: msi, address
> ac:1f:6b:b1:d2:08
> em1 at pci0 dev 20 function 1 "Intel I354 SGMII" rev 0x03: msi, address
> ac:1f:6b:b1:d2:09
> em2 at pci0 dev 20 function 2 "Intel I354 SGMII" rev 0x03: msi, address
> ac:1f:6b:b1:d2:0a
> em3 at pci0 dev 20 function 3 "Intel I354 SGMII" rev 0x03: msi, address
> ac:1f:6b:b1:d2:0b
> ehci0 at pci0 dev 22 function 0 "Intel Atom C2000 USB" rev 0x03: apic 2
> int 23
> usb1 at ehci0: USB revision 2.0
> uhub1 at usb1 configuration 1 interface 0 "Intel EHCI root hub" rev
> 2.00/1.00 addr 1
> ahci0 at pci0 dev 23 function 0 "Intel Atom C2000 AHCI" rev 0x03: msi,
> AHCI 1.3
> scsibus1 at ahci0: 32 targets
> ahci1 at pci0 dev 24 function 0 "Intel Atom C2000 AHCI" rev 0x03: msi,
> AHCI 1.3
> ahci1: port 0: 6.0Gb/s
> scsibus2 at ahci1: 32 targets
> sd0 at scsibus2 targ 0 lun 0: <ATA, PNY CS900 120GB, CS90>
> naa.5f8db4c151800400
> sd0: 114473MB, 512 bytes/sector, 234441648 sectors, thin
> pcib0 at pci0 dev 31 function 0 "Intel Atom C2000 PCU" rev 0x03
> ichiic0 at pci0 dev 31 function 3 "Intel Atom C2000 PCU SMBus" rev 0x03:
> apic 2 int 18
> iic0 at ichiic0
> sdtemp0 at iic0 addr 0x18: stts2004
> iic0: addr 0x2e 00=42 words 00=4242 01=0000 02=0000 03=0000 04=0000
> 05=0000 06=0000 07=0000
> spdmem0 at iic0 addr 0x50: 8GB DDR3 SDRAM ECC PC3-12800 with thermal
> sensor
> isa0 at pcib0
> isadma0 at isa0
> pckbc0 at isa0 port 0x60/5 irq 1 irq 12
> pckbd0 at pckbc0 (kbd slot)
> wskbd0 at pckbd0 mux 1
> pms0 at pckbc0 (aux slot)
> wsmouse0 at pms0 mux 0
> pcppi0 at isa0 port 0x61
> spkr0 at pcppi0
> vmm0 at mainbus0: VMX/EPT (using slow L1TF mitigation)
> uhub2 at uhub1 port 1 configuration 1 interface 0 "Intel product 0x07db"
> rev 2.00/0.03 addr 2
> uhub3 at uhub2 port 1 configuration 1 interface 0 "Terminus Technology
> USB 2.0 Hub" rev 2.00/1.11 addr 3
> uhub4 at uhub2 port 3 configuration 1 interface 0 "ATEN International
> product 0x7000" rev 2.00/0.00 addr 4
> uhidev0 at uhub4 port 1 configuration 1 interface 0 "ATEN International
> product 0x2419" rev 1.10/1.00 addr 5
> uhidev0: iclass 3/1
> ukbd0 at uhidev0: 8 variable keys, 6 key codes
> wskbd1 at ukbd0 mux 1
> uhidev1 at uhub4 port 1 configuration 1 interface 1 "ATEN International
> product 0x2419" rev 1.10/1.00 addr 5
> uhidev1: iclass 3/1
> ums0 at uhidev1: 3 buttons, Z dir
> wsmouse1 at ums0 mux 0
> vscsi0 at root
> scsibus3 at vscsi0: 256 targets
> softraid0 at root
> scsibus4 at softraid0: 256 targets
> root on sd0a (070da3f4af65d174.a) swap on sd0b dump on sd0b
>
>
>
> --
> Chris
>
> __o "All I was trying to do was get home from work."
> _`\<,_ -Rosa Parks
> ___(*)/_(*)____.___o____..___..o...________ooO..._____________________
> Christopher Sean Hilton [chris/at/vindaloo/dot/com]
