Hi,
I tried to set up a RAID 1 softraid with raidframe, but no matter what
I try, the RAID refuses to configure. So please, if anyone has an idea
what I may have missed...
# raidctl -C raid0.conf raid0
raidctl: ioctl (RAIDFRAME_CONFIGURE) failed
this adds the following lines to the dmesg buffer:
raidlookup on device: /dev/wd3d failed !
vnode was NULL
vnode was NULL
RAIDFRAME: failed rf_ConfigureDisks with 2.
vnode was NULL
vnode was NULL
# cat raid0.conf
START array
1 2 0
START disks
/dev/wd3d
/dev/wd1d
START layout
128 1 1 1
START queue
fifo 100
I tried both with wd0d, wd1d (both exist) and with wd1d,wd3d (latter
doesn't physically exist), none of these is mounted or in use, in fact
nothing of wd1 is currently used. The line "raidlookup on device: ..."
contains the first in raid0.conf mentioned device.
disklabels:
# disklabel wd0
# Inside MBR partition 3: type A6 start 63 size 625137282
# /dev/rwd0c:
type: ESDI
disk: ESDI/IDE disk
label: ST3320620AS
flags:
bytes/sector: 512
sectors/track: 63
tracks/cylinder: 255
sectors/cylinder: 16065
cylinders: 38913
total sectors: 625142448
rpm: 3600
interleave: 1
trackskew: 0
cylinderskew: 0
headswitch: 0 # microseconds
track-to-track seek: 0 # microseconds
drivedata: 0
16 partitions:
# size offset fstype [fsize bsize cpg]
a: 16787862 63 4.2BSD 2048 16384 1
b: 2104515 16787925 swap
c: 625142448 0 unused 0 0
d: 606244905 18892440 RAID
# disklabel wd1
# Inside MBR partition 3: type A6 start 63 size 625137282
# /dev/rwd1c:
type: ESDI
disk: ESDI/IDE disk
label: ST3320620AS
flags:
bytes/sector: 512
sectors/track: 63
tracks/cylinder: 255
sectors/cylinder: 16065
cylinders: 38913
total sectors: 625142448
rpm: 3600
interleave: 1
trackskew: 0
cylinderskew: 0
headswitch: 0 # microseconds
track-to-track seek: 0 # microseconds
drivedata: 0
16 partitions:
# size offset fstype [fsize bsize cpg]
a: 16787862 63 4.2BSD 2048 16384 1
b: 2104515 16787925 swap
c: 625142448 0 unused 0 0
d: 606244905 18892440 RAID
dmesg:
OpenBSD 4.2 (GENERIC.MP.RAID) #0: Thu Oct 11 03:21:12 CEST 2007
[EMAIL PROTECTED]:/usr/src/sys/arch/amd64/compile/GENERIC.MP.RAID
real mem = 3220762624 (3071MB)
avail mem = 3111911424 (2967MB)
mainbus0 at root
bios0 at mainbus0: SMBIOS rev. 2.4 @ 0xfbcf0 (50 entries)
bios0: vendor American Megatrends Inc. version "080011 " date 03/01/2007
bios0: Supermicro H8SSL-I2
acpi0 at mainbus0: rev 2
acpi0: tables DSDT FACP APIC OEMB SSDT
acpitimer at acpi0 not configured
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: AMD Athlon(tm) 64 X2 Dual Core Processor 6000+, 2992.93 MHz
cpu0:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,MMX,FXSR,SSE,SSE2,HTT,SSE3,CX16,NXE,MMXX,FFXSR,LONG,3DNOW2,3DNOW
cpu0: 64KB 64b/line 2-way I-cache, 64KB 64b/line 2-way D-cache, 1MB
64b/line 16-way L2 cache
cpu0: ITLB 32 4KB entries fully associative, 8 4MB entries fully associative
cpu0: DTLB 32 4KB entries fully associative, 8 4MB entries fully associative
cpu0: apic clock running at 199MHz
cpu1 at mainbus0: apid 1 (application processor)
cpu1: AMD Athlon(tm) 64 X2 Dual Core Processor 6000+, 2992.50 MHz
cpu1:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,MMX,FXSR,SSE,SSE2,HTT,SSE3,CX16,NXE,MMXX,FFXSR,LONG,3DNOW2,3DNOW
cpu1: 64KB 64b/line 2-way I-cache, 64KB 64b/line 2-way D-cache, 1MB
64b/line 16-way L2 cache
cpu1: ITLB 32 4KB entries fully associative, 8 4MB entries fully associative
cpu1: DTLB 32 4KB entries fully associative, 8 4MB entries fully associative
ioapic0 at mainbus0 apid 2 pa 0xfec00000, version 11, 16 pins
ioapic1 at mainbus0 apid 3 pa 0xfec01000, version 11, 16 pins
ioapic2 at mainbus0 apid 4 pa 0xfec02000, version 11, 16 pins
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus 1 (P0P1)
acpiprt2 at acpi0: bus 2 (P1P2)
acpicpu at acpi0 not configured
acpicpu at acpi0 not configured
acpibtn at acpi0 not configured
acpibtn at acpi0 not configured
pci0 at mainbus0 bus 0: configuration mode 1
ppb0 at pci0 dev 1 function 0 "ServerWorks HT-1000 PCI" rev 0x00
pci1 at ppb0 bus 1
ppb1 at pci1 dev 13 function 0 "ServerWorks HT-1000 PCIX" rev 0xb2
pci2 at ppb1 bus 2
bge0 at pci2 dev 3 function 0 "Broadcom BCM5704C" rev 0x10, BCM5704 B0
(0x2100): apic 3 int 8 (irq 9), address 00:30:48:5e:6d:f6
brgphy0 at bge0 phy 1: BCM5704 10/100/1000baseT PHY, rev. 0
bge1 at pci2 dev 3 function 1 "Broadcom BCM5704C" rev 0x10, BCM5704 B0
(0x2100): apic 3 int 9 (irq 5), address 00:30:48:5e:6d:f7
brgphy1 at bge1 phy 1: BCM5704 10/100/1000baseT PHY, rev. 0
pciide0 at pci1 dev 14 function 0 "ServerWorks HT-1000 SATA" rev 0x00: DMA
pciide0: using apic 2 int 11 (irq 11) for native-PCI interrupt
pciide0: port 0: device present, speed: 1.5Gb/s
wd0 at pciide0 channel 0 drive 0: <ST3320620AS>
wd0: 16-sector PIO, LBA48, 305245MB, 625142448 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5
pciide0: port 1: device present, speed: 1.5Gb/s
wd1 at pciide0 channel 1 drive 0: <ST3320620AS>
wd1: 16-sector PIO, LBA48, 305245MB, 625142448 sectors
wd1(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 5
pciide0: port 2: PHY offline
pciide0: port 3: PHY offline
pciide1 at pci1 dev 14 function 1 "ServerWorks HT-1000 SATA" rev 0x00
piixpm0 at pci0 dev 2 function 0 "ServerWorks HT-1000" rev 0x00: polling
iic0 at piixpm0
iic0: addr 0x2f 00=80 05=a0 06=ff 07=a0 08=ff 09=64 0a=64 0b=5e 0c=73
0d=5c 0e=7b 0f=12 10=b2 11=2f 13=ff 14=22 15=6f 16=d0 17=7b 18=d0
19=d0 1a=c0 1c=22 1d=9d 1e=80 1f=80 20=1d 21=51 22=01 23=0f 25=0f
27=0f 29=0f 2b=0f 3b=ff 3c=ff 3d=ff 3e=ff 3f=ff 40=09 44=40 46=f7
47=ff 48=ff 49=7f 4a=3f 4b=02 4d=7c 50=1e 51=02 52=01 58=80 59=01
5c=03 5e=55 5f=03 60=ca 61=87 62=ca 63=87 64=ff 66=ff 67=ff 68=3f
6a=2b 6b=18 6c=7c 6d=65 6e=e3 6f=b9 70=8a 71=70 72=e5 73=bb 74=e5
75=bb 76=e3 77=b9 78=48 79=43 7a=48 7b=43 7c=48 7d=5f 7e=55 7f=50
80=64 81=5f 82=55 83=50 84=64 85=5f 86=55 87=50 88=46 89=41 8a=55
8b=50 8c=64 8d=5f 8e=55 8f=50 90=07 91=68 92=07 93=68 94=07 95=68
96=07 97=68 98=07 99=68 9a=07 9b=68 9c=07 9d=68 9e=ff 9f=ff a0=ff
a1=ff a2=ff a3=ff a4=ff a5=ff a6=ff a7=ff a8=f5 ae=ff af=ff b1=04
b2=30 b3=30 b4=30 b5=30 b6=30 b7=30 b8=30 b9=30 ba=30 bb=89 bc=89
bd=89 be=89 bf=89 c0=89 c1=89 c2=89 c3=01 c4=01 c5=7f c6=ff c9=ff
ca=ff cb=ff cc=ff cd=ff ce=ff cf=ff d1=46 d2=46 d3=46 d4=46 d6=f0
d7=ff d8=80 d9=01 da=80 db=01 dc=80 dd=01 de=80 df=01 e0=bb e1=c0
e2=82 e3=ff e4=80 e5=06 e6=fe e7=12 e8=12 e9=12 ea=c8 eb=60 ec=ff
ed=ff ee=ff ef=ff f6=60 f7=80 f8=1b fa=ff fd=10
piixpm0: exec: op 1, addr 0x4b, cmdlen 1, len 1, flags 0x08: timeout,
status 0x9<BUSY,BUSERR>
pciide2 at pci0 dev 2 function 1 "ServerWorks HT-1000 IDE" rev 0x00: DMA
atapiscsi0 at pciide2 channel 0 drive 1
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <TEAC, DV-28E-R, 1.8A> SCSI0 5/cdrom removable
cd0(pciide2:0:1): using PIO mode 4, DMA mode 2, Ultra-DMA mode 0
pcib0 at pci0 dev 2 function 2 "ServerWorks HT-1000 LPC" rev 0x00
ohci0 at pci0 dev 3 function 0 "ServerWorks HT-1000 USB" rev 0x01:
apic 2 int 10 (irq 10), version 1.0, legacy support
ohci1 at pci0 dev 3 function 1 "ServerWorks HT-1000 USB" rev 0x01:
apic 2 int 10 (irq 10), version 1.0, legacy support
ehci0 at pci0 dev 3 function 2 "ServerWorks HT-1000 USB" rev 0x01:
apic 2 int 10 (irq 10)
usb0 at ehci0: USB revision 2.0
uhub0 at usb0: ServerWorks EHCI root hub, rev 2.00/1.00, addr 1
vga1 at pci0 dev 5 function 0 "ATI ES1000" rev 0x02
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
pchb0 at pci0 dev 24 function 0 "AMD AMD64 HyperTransport" rev 0x00
pchb1 at pci0 dev 24 function 1 "AMD AMD64 Address Map" rev 0x00
pchb2 at pci0 dev 24 function 2 "AMD AMD64 DRAM Cfg" rev 0x00
pchb3 at pci0 dev 24 function 3 "AMD AMD64 Misc Cfg" rev 0x00
isa0 at pcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
usb1 at ohci0: USB revision 1.0
uhub1 at usb1: ServerWorks OHCI root hub, rev 1.00/1.00, addr 1
usb2 at ohci1: USB revision 1.0
uhub2 at usb2: ServerWorks OHCI root hub, rev 1.00/1.00, addr 1
Kernelized RAIDframe activated
dkcsum: wd0 matches BIOS drive 0x80
dkcsum: wd1 matches BIOS drive 0x81
root on wd0a swap on wd0b dump on wd0b
--knitti
