Hi all,
I'm trying to get misdn/Asterisk/Freepbx running inside a virtualized
Debian etch machine, and everything looks pretty fine so far, however
Asterisk reports all channels being busy when trying to dial out.
Could someone help me how to debug this problem?
asterisk:~# uname -r
2.6.18-4-xen-686
asterisk:~# lspci -v
00:00.0 Network controller: Cologne Chip Designs GmbH ISDN network
controller [HFC-PCI] (rev 02)
Subsystem: Cologne Chip Designs GmbH ISDN Board
Flags: bus master, medium devsel, latency 16, IRQ 18
I/O ports at ac00 [disabled] [size=8]
Memory at ff6ffc00 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 1
asterisk:~# misdn-init scan
[OK] found the following devices:
card=1,hfcpci
[ii] run "/usr/sbin/misdn-init config" to store this information to /
etc/misdn-init.conf
asterisk:~# misdn-init config
[OK] /etc/misdn-init.conf created. It's now safe to run "/usr/sbin/
misdn-init start"
[ii] make your port (1) available in asterisk by editing "/etc/
asterisk/misdn.conf"
asterisk:~# misdn-init start
-----------------------------------------
Loading module(s) for your misdn-cards:
-----------------------------------------
/sbin/modprobe --ignore-install hfcpci protocol=0x2 layermask=0xf
/sbin/modprobe mISDN_dsp debug=0x0 options=0 poll=128 dtmfthreshold=100
[i] creating device node: /dev/mISDN
asterisk:~# ls -al /dev/mISDN
crw-r--r-- 1 asterisk asterisk 46, 0 Jul 3 20:07 /dev/mISDN
asterisk:~# cat /etc/misdn-init.conf
card=1,hfcpci
te_ptmp=1
poll=128
dsp_poll=128
dsp_options=0
dtmfthreshold=100
debug=0
asterisk:~# cat /etc/asterisk/misdn.conf
[general]
misdn_init=/etc/misdn-init.conf
debug=0
ntdebugflags=0
ntdebugfile=/var/log/misdn-nt.log
bridging=no
stop_tone_after_first_digit=yes
append_digits2exten=yes
dynamic_crypt=no
crypt_prefix=**
crypt_keys=test,muh
[default]
context=misdn
language=en
musicclass=default
senddtmf=yes
far_alerting=no
allowed_bearers=all
nationalprefix=0
internationalprefix=00
rxgain=0
txgain=0
te_choose_channel=no
pmp_l1_check=yes
reject_cause=16
need_more_infos=no
method=standard
dialplan=0
localdialplan=0
cpndialplan=0
early_bconnect=yes
incoming_early_audio=no
nodialtone=no
presentation=-1
screen=-1
jitterbuffer=4000
jitterbuffer_upper_threshold=0
hdlc=no
[extern]
ports=1
context=from-pstn
msns=*
I'm a bit unsure about the last stance here but documentation is
pretty sparse.
I have a suspiciously looking error in my syslog as well:
Jul 4 05:45:15 asterisk kernel: MDL_ERROR|REQ (tei_l2)
when restarting Asterisk. I've also explicitly unloaded the hisax
module, re-init-ed msidn, restarted Asterisk: same error.
Many thanks!
</Steven>
--
Steven Noels http://outerthought.org/
Outerthought Open Source Java & XML
stevenn at outerthought.org stevenn at apache.org
_______________________________________________
Misdn-asterisk mailing list
[email protected]
http://lists.beronet.com/cgi-bin/mailman/listinfo/misdn-asterisk
