I'd like to know if there is a specific location for the high and low presure senders.
> Coolant temp gauge located directly below distributor. Normally this sender > is black. The one I had on there was black but VW suggested I go with the White sender. I thought that maybe someone had put the wrong sender on. I noticed that with the white sender my temps were well above the half way mark. Thanks, Mark Reda. > > >From: "Mark Reda" <[email protected]> > >To: "a2list" <[email protected]>,<[email protected]> > >Subject: Re: [a2-16v-list] A few Wiring Questions > >Date: Fri, 22 Oct 2004 23:02:41 -0400 > > > >Next question..... > >On the oil filter flange does it matter where each oil pressure sender is > >located? > > > >On the side of the head which sender (left or right) is used for the > >Coolant > >temp gauge? > >What colour is the sender (white or black)? > > > >Thanks, > >Mark Reda. > > > >----- Original Message ----- > >From: "Galen Bergthold" <[email protected]> > >To: <[email protected]> > >Sent: Friday, October 22, 2004 10:19 PM > >Subject: Re: [a2-16v-list] A few Wiring Questions > > > > > > > From the Bentley ch 3 p 41: > > > Dynamic Oil Pressure Warning System > > > "On 16-valve engines, both switches are located on the filter flange." > > > > > > > > > >From: "Mark Reda" <[email protected]> > > > >To: "Galen Bergthold" <[email protected]>,"a2list" > > > ><[email protected]> > > > >Subject: Re: [a2-16v-list] A few Wiring Questions > > > >Date: Fri, 22 Oct 2004 21:24:44 -0400 > > > > > > > >Anyone correct me if I'm wrong.... > > > > > > > >1. Engine oil temp sensor G/BK > > > >is the oil temp sensor is on the oil filter housing? > > > >my green/black wire is on the back of the head. > > > > > > > >2. Engine oil press sw 0.3 bar BL/BK > > > >my blue/black is located near the oil filter housing., I thought the > >low > > > >pressure switch was on the back of the head. > > > > > > > >3. Engine oil press sw 1.8 bar Y > > > >my Yellow is located on the oil filter housing. > > > >The yellow wire hooks up to the black oil press. switch? > > > > > > > >4. Coolant temp send unit Y/R > > > >This one is right! > > > > > > > > > > > > > > > >----- Original Message ----- > > > >From: "Galen Bergthold" <[email protected]> > > > >To: <[email protected]> > > > >Sent: Friday, October 22, 2004 8:12 PM > > > >Subject: RE: [a2-16v-list] A few Wiring Questions > > > > > > > > > > > > > From the Bentley, p.226 fora 91-92 Jetta GLI, German production: > > > > > Engine oil temp sensor G/BK > > > > > Engine oil press sw 0.3 bar BL/BK > > > > > Engine oil press sw 1.8 bar Y > > > > > Coolant temp send unit Y/R > > > > > > > > > > > > > > > >From: "Mark Reda" <[email protected]> > > > > > >To: "a2list" <[email protected]> > > > > > >Subject: [a2-16v-list] A few Wiring Questions > > > > > >Date: Fri, 22 Oct 2004 18:08:05 -0400 > > > > > > > > > > > >I'm putting the head back on my 16V and I'm having a hard time > >figuring > > > >out > > > > > >which wires connect to a few senders on a 9A with CIS-E Motronic > >(91 > > > > > >GTX)..... > > > > > > > > > > > >Which colour wires are for the.... > > > > > >1. Black oil pressure sender on the oil filter housing > > > > > >2. MFA temp sender on the oil filter housing > > > > > >3. Coolant gauge temp sender on the side of the block under the > > > >distributor > > > > > >4. Blue oil pressure sender on back of the head > > > > > > > > > > > >Thanks, > > > > > >Mark. > > > > > >_______________________________________________ > > > > > >a2-16v-list mailing list > > > > > >[email protected] > > > > > >http://mail.a2-16v.com/mailman/listinfo/a2-16v-list > > > > > >For list archives, see listinfo link above. > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > >
