I am running 6.1 and I can get the connections to work by using the config below. I cannot get the CPU stats. I guess 6.2 will fix that for me.
Target[172.16.4.3_Conn]:1.3.6.1.4.1.9.9.147.1.2.2.2.1.5.40.6&.1.3.6.1.4. 1.9.9.147.1.2.2.2.1.5.40.7:[EMAIL PROTECTED] YLegend[172.16.4.3_Conn]: Connections ShortLegend[172.16.4.3_Conn]: Connections MaxBytes[172.16.4.3_Conn]: 3000 Options[172.16.4.3_Conn]: nopercent, gauge, unknaszero Unscaled[172.16.4.3_Conn]: dwmy Legend1[172.16.4.3_Conn]: PIX-515E (Primary) User Connections Legend2[172.16.4.3_Conn]: Max Connections since reboot Legend3[172.16.4.3_Conn]: Max value per interval on graph Legend4[172.16.4.3_Conn]: . LegendI[172.16.4.3_Conn]: Reading. LegendO[172.16.4.3_Conn]: Since Reboot. Title[172.16.4.3_Conn]: PIX Firewall PageTop[172.16.4.3_Conn]: <H1>PIX-515E Firewall (Primary) - Connection stats.</H1> Colours[172.16.4.3_Conn]: GREEN#00eb0c,BLUE#0000ff,GRAY#AAAAAA,VIOLET#ff00ff WithPeak[172.16.4.3_Conn]: ymw -----Original Message----- From: Bill Parker [mailto:[EMAIL PROTECTED] Sent: Tuesday, February 25, 2003 11:30 AM To: McDaniel, Scott Cc: [EMAIL PROTECTED] Subject: [mrtg] Re: PIX-515E CPU/Connection woes At 08:11 AM 2/25/2003 -0800, you wrote: >I had the same results - I am told I need to upgrade my IOS to 6.2(2) as the >version I am running - 6.0(3) does not support the process MIB which is >where all the CPU stats reside. Well, I am running 6.2(2) this is what a 'sh ver' returns: Cisco PIX Firewall Version 6.2(2) Cisco PIX Device Manager Version 1.1(2) Compiled on Fri 07-Jun-02 17:49 by morlee DonBest-pix up 7 days 7 hours Hardware: PIX-515E, 64 MB RAM, CPU Pentium II 433 MHz Flash E28F128J3 @ 0x300, 16MB BIOS Flash AM29F400B @ 0xfffd8000, 32KB Encryption hardware device : IRE2141 with 2048KB, HW:1.0, CGXROM:1.9, FW:6.5 0: ethernet0: address is 0009.b7f7.68c0, irq 10 1: ethernet1: address is 0009.b7f7.68c1, irq 11 2: ethernet2: address is 00e0.b606.993b, irq 11 3: ethernet3: address is 00e0.b606.993a, irq 10 4: ethernet4: address is 00e0.b606.9939, irq 9 5: ethernet5: address is 00e0.b606.9938, irq 5 Licensed Features: Failover: Enabled VPN-DES: Enabled VPN-3DES: Disabled Maximum Interfaces: 6 Cut-through Proxy: Enabled Guards: Enabled URL-filtering: Enabled Inside Hosts: Unlimited Throughput: Unlimited IKE peers: Unlimited Serial Number: 806272648 (0x300ebe88) Running Activation Key: 0xf690c830 0xb48c361d 0x863c3547 0x842d13b3 Configuration last modified by enable_15 at 07:38:09.115 UTC Fri Jan 8 1993 pix# sh cpu Usage: show cpu usage pix# sh cpu usage CPU utilization for 5 seconds = 0%; 1 minute: 0%; 5 minutes: 0% When I do a 'sh conn' I get this pix# sh conn 894 in use, 1881 most used So the PIX is able to store this information somewhere, I just can't seem to get at it GRRRRR :) -Bill -- Unsubscribe mailto:[EMAIL PROTECTED] Archive http://www.ee.ethz.ch/~slist/mrtg FAQ http://faq.mrtg.org Homepage http://www.mrtg.org WebAdmin http://www.ee.ethz.ch/~slist/lsg2.cgi -- Unsubscribe mailto:[EMAIL PROTECTED] Archive http://www.ee.ethz.ch/~slist/mrtg FAQ http://faq.mrtg.org Homepage http://www.mrtg.org WebAdmin http://www.ee.ethz.ch/~slist/lsg2.cgi
