Thank you gentlemen, that is exactly what had to be done in order to MIB walk the ISA server. MRTG is up and running on all interfaces. _____
From: Alvaro Luiz Maia Motta [mailto:[EMAIL PROTECTED] Sent: Wednesday, October 06, 2004 3:25 PM To: RL Glauser; [EMAIL PROTECTED]; [EMAIL PROTECTED] Subject: RE: [mrtg] Re: MRTG and ISA server Is the ISA server listening to udp packets on port 161? netstat -an -p udp will show all the udp ports your box is listening. If you find a line like the one below, and you're sure about the filters and community name, then I would suggest you to reinstall snmp on your box. UDP 0.0.0.0:161 *:* HTH -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Sent: Wednesday, October 06, 2004 4:18 PM To: [EMAIL PROTECTED]; [EMAIL PROTECTED] Subject: [mrtg] Re: MRTG and ISA server I have configured a packet filter allowing udp port 161 both ways on the ISA server and it made no difference. -----Original Message----- From: Garth Williams [mailto:[EMAIL PROTECTED] Sent: Wednesday, October 06, 2004 12:41 PM To: RL Glauser; [EMAIL PROTECTED] Subject: RE: [mrtg] Re: MRTG and ISA server On ISA server, you need to configure a packet filter to allow UDP port 161 in and out from the internal network. * I tried running getif on the ISA server itself and there was no response at all. I suspect that it has to do with security settings within ISA itself, or perhaps MIB files that are incorrect. * Did you try to run getif (or any other snmp utility) on the same box (localhost or 127.0.0.1)? * I have checked the SNMP service configuration. I have tested it with listed hosts and with "from any hosts." I have made sure that the xp firewall is disabled. The service is running on the ISA server and Getif does return some data but only identifies one of the three nic cards in the server. -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of William Owen Sent: Wednesday, October 06, 2004 10:09 AM To: [EMAIL PROTECTED] Subject: [mrtg] Re: MRTG and ISA server You might want to check your SNMP service configuration. By default, Win2k and Win2k3 server will respond to only to hosts listed in the security tab (localhost by default). If you have "from these hosts" selected, you MUST have your monitoring server listed. Also, if you use a NetBIOS or DNS name here, your server must be able to resolve the name. To alleviate both of these issues, you can use the "from any host" to test. -----Original Message----- From: Garth Williams [mailto:[EMAIL PROTECTED] Sent: Tuesday, October 05, 2004 5:55 PM To: [EMAIL PROTECTED]; [EMAIL PROTECTED] Subject: [mrtg] Re: MRTG and ISA server http://www.loriotpro.com/Service&Support/How_to/InstallWXPAgent_EN.php * Neither mib walker is on a server. One is on W2K pro and the other XP. I am not aware of any way to place an ACL on the snmp service running on a server. * Is Solarwinds on another server than GetIf? If so, then perhaps the SNMP service on the target is set to allow SNMP access from the Getif server and not the SolarWindws service. * Yes the solarwinds mib walker is polling on UDP port 161 and can successfully poll other serers. * Is your SNMP poll/walk/whatever from Solarwinds on the same UDP port as GetIf? Or does it poll on another port? Can you use Solarwindws to poll another server to verify settings? * I am having a problem setting up MRTG on ISA server 2000. <SNIP> -- Unsubscribe mailto:[EMAIL PROTECTED] Archive http://www.ee.ethz.ch/~slist/mrtg FAQ http://faq.mrtg.org Homepage http://www.mrtg.org WebAdmin http://www.ee.ethz.ch/~slist/lsg2.cgi -- Unsubscribe mailto:[EMAIL PROTECTED] Archive http://www.ee.ethz.ch/~slist/mrtg FAQ http://faq.mrtg.org Homepage http://www.mrtg.org WebAdmin http://www.ee.ethz.ch/~slist/lsg2.cgi
