sorry for sending a private email. My mistake. On 5/20/10 12:39 PM Niall O'Reilly wrote: > On 20/05/10 08:36, Richard Gliebe wrote: >> Hi Niall,
me onesmore ;-) > > If Perl coding is not something you feel confident about, > you may prefer to drop sections like the following (generated > by the code I sent) into your configuration file. > > Beware of line folding during mail-sending or -receipt! > > ### Unit wbs-qusb-001 > > ### Interface 1 >> Descr: 'Dot11Radio0' | Name: 'Do0' | Ip: '' | Eth: '' ### > > # wbs-qusb-001 cDot11ActiveWirelessClients > Target[wbs-qusb-001-wlclients-Do0]: > 1.3.6.1.4.1.9.9.273.1.1.2.1.1#Do0&1.3.6.1.4. > 1.9.9.273.1.1.2.1.1#Do0:pub...@wbs-qusb-001:::::2 > Directory[wbs-qusb-001-wlclients-Do0]: wbs-qusb-001 > Title[wbs-qusb-001-wlclients-Do0]: Active wireless clients on > wbs-qusb-001 Do0 > PageTop[wbs-qusb-001-wlclients-Do0]: wbs-qusb-001 Do0</H1> > <TABLE> > <TR><TD>System:</TD><TD>wbs-qusb-001.ucd.ie</TD></TR> > <TR><TD> </TD><TD>Active Wireless Clients</TD></TR> > </TABLE> > > ### END Interface I put the above lines into my cfg file, put a <H> into the line "PageTop". While I'm tried to build a new html file, MRTG told me, that there is a line called 'MaxBytes' missing in my cfg file. So I included this line, [...] MaxBytes[ap-w106-19.uclv.net-wlclients-Do0]: 35 [...] and build the html file successfully. I think this line should called like "MaxClients" or something similar to the connected wireless clients?? ;-) here is the part of my new cfg File. Attention: some lines are brocken from cut&paste. [...] ###################################################################### # System: ap-w106-19.uclv.net # Description: Cisco IOS Software, C1200 Software (C1200-K9W7-M), Version 12.3(7)JA5, RELEASE SOFTWARE (fc3) # Technical Support: http://www.cisco.com/techsupport # Copyright (c) 1986-2007 by Cisco Systems, Inc. # Compiled Fri 27-Jul-07 14:00 by kehsiao # Contact: # Location: ###################################################################### ### Interface 1 >> Descr: 'Dot11Radio0' | Name: 'Do0' | Ip: '' | Eth: '' ### # ap-w106-19.uclv.net cDot11ActiveWirelessClients Target[ap-w106-19.uclv.net-wlclients-Do0]:1.3.6.1.4.1.9.9.273.1.1.2.1.1#Do0&1.3.6.1.4.1.9.9.273.1.1.2.1.1#Do0:uclvN [email protected]:::::2 Directory[ap-w106-19.uclv.net-wlclients-Do0]: ap-w106-19.uclv.net MaxBytes[ap-w106-19.uclv.net-wlclients-Do0]: 35 Title[ap-w106-19.uclv.net-wlclients-Do0]: Active wireless clients on ap-w106-19.uclv.net Do0 PageTop[ap-w106-19.uclv.net-wlclients-Do0]: <H1>ap-w106-19.uclv.net Do0 WLAN Clients</H1> <TABLE> <TR><TD>System:</TD><TD>ap-w106-19.uclv.net</TD></TR> <TR><TD> </TD><TD>Active Wireless Clients</TD></TR> </TABLE> ### END Interface ### Interface 1 >> Descr: 'Dot11Radio0' | Name: 'Do0' | Ip: '' | Eth: '' ### Target[ap-w106-19.uclv.net_1]: 1:[email protected]: SetEnv[ap-w106-19.uclv.net_1]: MRTG_INT_IP="" MRTG_INT_DESCR="Dot11Radio0" Directory[ap-w106-19.uclv.net_1]: ap-w106-19.uclv.net MaxBytes[ap-w106-19.uclv.net_1]: 6750000 Title[ap-w106-19.uclv.net_1]: Dot11Radio0 -- ap-w106-19.uclv.net PageTop[ap-w106-19.uclv.net_1]: <h1>Dot11Radio0 -- ap-w106-19.uclv.net</h1> <div id="sysdetails"> and so on ... [...] Now, the web interface shows me the traffic and not the connected clients. At this moment, one Client is connected to this AP: k2# ./check_conn_rad0 ap-w106-19.uclv.net 20 35 Connections Dot11Radio0 OK: 1 Where is the missmatch or is there missing something else? many thanks Richard _______________________________________________ mrtg mailing list [email protected] https://lists.oetiker.ch/cgi-bin/listinfo/mrtg
