Hi Steve, thanks for your quick reply. A few more data further to your good points:
1) Webpages are updated every 5 minutes and here is the /etc/cron.d/mrtg file: 2) /var/www/html and all its content is set to 777 and anyway graph files are dated correctly after each execution of the crontab 3) I did. Here are the logs: 2011-01-31 11:02:40 -- Started mrtg with config '/etc/mrtg/mrtg.cfg' 2011-01-31 11:02:40 -- Monday, 31 January 2011 at 11:02: ERROR: Target[r1][_IN_] '[email protected]' (warn): (Missing operator before ?) 2011-01-31 11:02:40 -- Monday, 31 January 2011 at 11:02: ERROR: Target[r1][_OUT_] '[email protected]' (warn): (Missing operator before ?) What does this mean? Any more clues? Thanks, Andrea S Shipway wrote: > > What happens when you run MRTG to collect the data? > > Either the data are not being gathered (scheduler or SNMP issue) or they > cannot be stored (permissions issue) > > 1. Make sure you are actually runnning MRTG -- either as a daemon, or via > cron every 5min. > 2. Make sure the appropriate directories and files are writeable by the > mrtg process > 3. Run MRTG interactively as the normal user it runs as. Is it producing > any error messages that might clue you in to why the data are not being > gathered? > > Steve > > Steve Shipway > University of Auckland ITS > UNIX Systems Design Lead > [email protected] > Ph: +64 9 373 7599 ext 86487 > > > ________________________________________ > From: [email protected] > [[email protected]] on behalf of > andrea.corelli [[email protected]] > Sent: Monday, 31 January 2011 10:23 a.m. > To: [email protected] > Subject: [mrtg] No Data (again) > > Hi people! > First of all thank you so much for taking your time to read this and see > if > you can spot anything that causes my troubles. I have searching a little > on > the forum and I did not find anyone having similar trobles. > > I have MRTG running on a 5.5 final CentOS Linux. Pages and graphs are > generated correctly but apparently the traffic is not monitored for some > reasons. > > mrtg.cfg > > HtmlDir: /var/www/mrtg > ImageDir: /var/www/mrtg > LogDir: /var/lib/mrtg > ThreshDir: /var/lib/mrtg > Target[r1]: [email protected] > MaxBytes[r1]: 1250000 > Title[r1]: Traffic Analysis > PageTop[r1]: <H1>Stats for our Ethernet</H1> > > snmp.conf > > com2sec local localhost public > group public any local > view all included .1 80 > access public "" any noauth 0 all none none > trapsink 127.0.0.1 public > trap2sink 127.0.0.1 public > mibs +MIB-Dell-10892:StorageManagement-MIB > > The public webpage is here: http://www.listen.to.it/mrtg/r1.html > > Anyone got any clues? Please excuse my ignorance in advance. > Thanks, > Andrea > -- > View this message in context: > http://mrtg-mailinglists.795376.n2.nabble.com/No-Data-again-tp5975466p5975466.html > Sent from the MRTG Users Mailinglist mailing list archive at Nabble.com. > > _______________________________________________ > mrtg mailing list > [email protected] > https://lists.oetiker.ch/cgi-bin/listinfo/mrtg > > _______________________________________________ > mrtg mailing list > [email protected] > https://lists.oetiker.ch/cgi-bin/listinfo/mrtg > > S Shipway wrote: > > What happens when you run MRTG to collect the data? > > Either the data are not being gathered (scheduler or SNMP issue) or they > cannot be stored (permissions issue) > > 1. Make sure you are actually runnning MRTG -- either as a daemon, or via > cron every 5min. > 2. Make sure the appropriate directories and files are writeable by the > mrtg process > 3. Run MRTG interactively as the normal user it runs as. Is it producing > any error messages that might clue you in to why the data are not being > gathered? > > Steve > > Steve Shipway > University of Auckland ITS > UNIX Systems Design Lead > [email protected] > Ph: +64 9 373 7599 ext 86487 > > > ________________________________________ > From: [email protected] > [[email protected]] on behalf of > andrea.corelli [[email protected]] > Sent: Monday, 31 January 2011 10:23 a.m. > To: [email protected] > Subject: [mrtg] No Data (again) > > Hi people! > First of all thank you so much for taking your time to read this and see > if > you can spot anything that causes my troubles. I have searching a little > on > the forum and I did not find anyone having similar trobles. > > I have MRTG running on a 5.5 final CentOS Linux. Pages and graphs are > generated correctly but apparently the traffic is not monitored for some > reasons. > > mrtg.cfg > > HtmlDir: /var/www/mrtg > ImageDir: /var/www/mrtg > LogDir: /var/lib/mrtg > ThreshDir: /var/lib/mrtg > Target[r1]: [email protected] > MaxBytes[r1]: 1250000 > Title[r1]: Traffic Analysis > PageTop[r1]: <H1>Stats for our Ethernet</H1> > > snmp.conf > > com2sec local localhost public > group public any local > view all included .1 80 > access public "" any noauth 0 all none none > trapsink 127.0.0.1 public > trap2sink 127.0.0.1 public > mibs +MIB-Dell-10892:StorageManagement-MIB > > The public webpage is here: http://www.listen.to.it/mrtg/r1.html > > Anyone got any clues? Please excuse my ignorance in advance. > Thanks, > Andrea > -- > View this message in context: > http://mrtg-mailinglists.795376.n2.nabble.com/No-Data-again-tp5975466p5975466.html > Sent from the MRTG Users Mailinglist mailing list archive at Nabble.com. > > _______________________________________________ > mrtg mailing list > [email protected] > https://lists.oetiker.ch/cgi-bin/listinfo/mrtg > > _______________________________________________ > mrtg mailing list > [email protected] > https://lists.oetiker.ch/cgi-bin/listinfo/mrtg > > -- View this message in context: http://mrtg-mailinglists.795376.n2.nabble.com/No-Data-again-tp5975466p5976654.html Sent from the MRTG Users Mailinglist mailing list archive at Nabble.com. _______________________________________________ mrtg mailing list [email protected] https://lists.oetiker.ch/cgi-bin/listinfo/mrtg
