I located and checked the file opie_config.xml and it looked pretty much like yours (with Ip="192.168.129.201" -- the default configuration for Zaurus -- instead).
I tried sftp -oPort=22 [EMAIL PROTECTED] and it worked just fine. I also have a wireless card and I tried the same for that IP address. It also works as expected with the command line sftp (I get prompted for the password and then, I am logged on), but not with MultiSync. Port=115 does not work. Joakim On Wed, 2003-11-12 at 07:09, Tom Foottit wrote: > Interesting. I keep a few configurations around to test syncing with my > iPaq running Familiar Linux and Opie, and my 0.80 configuration on my > machine with ssh host keys set up looks like: > > <?xml version="1.0"?> > <Config> > <Options Ip="192.168.2.2" Username="root" Password="rootme" Port="22" > Protocol="SFTP" Device="1"/> > </Config> > > So this apparently works with Familiar Linux. Can someone out there > running OpenZaurus confirm their SFTP configuration? > > The other thing I can think of trying is try to run 'sftp -o Port=22 ...' > from the command line to see if that works to connect to your device, or > if not perhaps try port 115. > > Tom > > > On Tue, 11 Nov 2003, Joakim Kalvenes wrote: > > > Tom, > > > > Thanks for your response. When I set the SFTP port to 22, I get the > > following message in the MultiSync log: > > > > Tue Nov 11 14:40:05 2003 Failed to connect remote: Failed to load data > > from device 192.168.129.201. (repeated 19 times) > > > > In other words, I fail to make a connection. Is there some parameter I > > have to set in /etc/services or some such file on the Z to make it work > > (currently, ssh is associated with port 22, while sftp is associated > > with port 115)? > > > > Joakim > > > > On Tue, 2003-11-11 at 14:30, Tom Foottit wrote: > > > You need to set the SFTP port to 22. Setting it to blank (it actually > > > ends up as 0) gets you transfer in one direction but not the other. The > > > CVS version of Multisync actually doesn't allow you to set a blank port. > > > > > > Also, if you make a change in the Z PIM applications you have to sync > > > manually or wait for multisync to reach its next sync interval - it > > > can't detect that the changes were made automatically. > > > > > > Let me know if that helps. > > > > > > Tom > > > > > > > > > On Tue, 2003-11-11 at 14:35, Joakim Kalvenes wrote: > > > > I have installed Evolution 1.4.5 on my desktop running Mandrake Linux > > > > 9.1. I have also installed MultiSync 0.80 and configured the > > > > synchronization pair as follows: > > > > > > > > First Plugin: Ximian Evolution (no changes to default options) > > > > Second Plugin: Opie and Zaurus (Options - Type: Opie/OpenZaurus, > > > > Protocol: SFTP, IP Address: 192.168.129.201, Port: <blank>; valid user > > > > name and password) > > > > > > > > The Sharp Zaurus SL-5500 PDA is running OpenZaurus 3.2 with default PIM > > > > applications (Opie). I have an SD card holding most applications and > > > > data. I followed the OZ installation instructions and placed the PIM > > > > application data in > > > > /mnt/card/root/Applications/<addressbook,datebook,todolist>, where each > > > > of the three directories contains the corresponding .xml file. There is > > > > a symlink from /root/Applications to /mnt/card/root/Applications > > > > > > > > I have established an SFTP connection and transferred .ipk files from my > > > > desktop to the Z and, subsequently, installed them on the Z. I feel > > > > fairly confident that the networking part is operational. > > > > > > > > The MultiSync Status line shows: Waiting for change. > > > > > > > > The MultiSync log shows the following line: > > > > > > > > Tue Nov 11 13:19:46 2003 Synchronization of 4 entries succeeded. > > > > (repeated 2 times) > > > > > > > > However, no data exchange takes place during the synchronization > > > > (entries in Evolution do not appear in the Z PIM and vice versa). If I > > > > make a change in the Z PIM applications, nothing registers in MultiSync. > > > > But, if I add an entry to the Evolution Calendar, MultiSync detects it > > > > and performs the synchronization (again, without any data exchange). > > > > > > > > Apparently, there is something I have not configured correctly with > > > > respect to the Z. Any help would be appreciated. > > > > > > > > Joakim > > > > > > > > > > > > > > > > ------------------------------------------------------- > > > > This SF.Net email sponsored by: ApacheCon 2003, > > > > 16-19 November in Las Vegas. Learn firsthand the latest > > > > developments in Apache, PHP, Perl, XML, Java, MySQL, > > > > WebDAV, and more! http://www.apachecon.com/ > > > > _______________________________________________ > > > > Multisync-users mailing list > > > > [EMAIL PROTECTED] > > > > https://lists.sourceforge.net/lists/listinfo/multisync-users > > ------------------------------------------------------- This SF.Net email sponsored by: ApacheCon 2003, 16-19 November in Las Vegas. Learn firsthand the latest developments in Apache, PHP, Perl, XML, Java, MySQL, WebDAV, and more! http://www.apachecon.com/ _______________________________________________ Multisync-users mailing list [EMAIL PROTECTED] https://lists.sourceforge.net/lists/listinfo/multisync-users
