|
-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 I am also using gentoo, and I didn't have the kernel options either. I had to compile the Lirc by hand being sure to select the haupage driver. Then I had to change the line in /etc/conf.d/lircd to the right direction, I just found the right place looking at the existing address. I think it was /dev/lirc/0. Then I tried everything using the irw command. Hope it helped. Juan Dennis B. Hopp wrote: |I've searched the archvies and the forums at http://forums.gentoo.org |and I'm having a hell of time getting the Gray remote that came with my |PVR-250 working. | |I followed the instructions here: | |http://gentoo-wiki.com/HARDWARE_Setup_MythTV | |When I do a make menuconfig I do not have any option to enable Linux |Infrared controller. lircd is using /dev/lirc/0. If I cat /dev/lirc/0 |and press buttons on the remote I get output on the screen (a bunch of |garbage, but output none the less). irw doesn't seem to do anything | |my /etc/lircd.conf: | |begin remote | | name Hauppauge | bits 13 | flags SHIFT_ENC | eps 30 | aeps 100 | | one 950 830 | zero 950 830 | plead 960 | gap 89584 | repeat_bit 2 | | begin codes | TV 0x000000000000100F | RADIO 0x000000000000100C | FULL_SCREEN 0x000000000000102E | CH+ 0x0000000000001020 | CH- 0x0000000000001021 | VOL- 0x0000000000001011 | VOL+ 0x0000000000001010 | MUTE 0x000000000000100D | SOURCE 0x0000000000001022 | 1 0x0000000000001001 | 2 0x0000000000001002 | 3 0x0000000000001003 | 4 0x0000000000001004 | 5 0x0000000000001005 | 6 0x0000000000001006 | 7 0x0000000000001007 | 8 0x0000000000001008 | 9 0x0000000000001009 | 0 0x0000000000001000 | RESERVED 0x000000000000101E | MINIMIZE 0x0000000000001026 | end codes | |end remote | | |begin remote | | name hauppauge_pvr | bits 13 | flags RC5|CONST_LENGTH | eps 30 | aeps 100 | | one 969 811 | zero 969 811 | plead 1097 | gap 114605 | toggle_bit 2 | | | begin codes | Power 0x00000000000017FD | Go 0x00000000000017FB | 1 0x00000000000017C1 | 2 0x00000000000017C2 | 3 0x00000000000017C3 | 4 0x00000000000017C4 | 5 0x00000000000017C5 | 6 0x00000000000017C6 | 7 0x00000000000017C7 | 8 0x00000000000017C8 | 9 0x00000000000017C9 | Back/Exit 0x00000000000017DF | 0 0x00000000000017C0 | Menu 0x00000000000017CD | Red 0x00000000000017CB | Green 0x00000000000017EE | Yellow 0x00000000000017F8 | Blue 0x00000000000017E9 | Ch+ 0x00000000000017E0 | Ch- 0x00000000000017E1 | Vol- 0x00000000000017D1 | Vol+ 0x00000000000017D0 | Ok 0x00000000000017E5 | Mute 0x00000000000017CF | Blank 0x00000000000017CC | Full 0x00000000000017FC | Rewind 0x00000000000017F2 | Play 0x00000000000017F5 | Forward 0x00000000000017F4 | Record 0x00000000000017F7 | Stop 0x00000000000017F6 | Pause 0x00000000000017F0 | Replay 0x00000000000017E4 | Skip 0x00000000000017DE | end codes | |end remote | |I've tried running mythfrontend as root and a normal user. | |my lircrc: | |begin | prog = irxevent | button = OK | repeat = 3 | config = Key M CurrentWindow |end |begin | prog = irxevent | button = CH+ | repeat = 3 | config = Key Up CurrentWindow |end |begin | prog = irxevent | button = CH- | repeat = 3 | config = Key Down CurrentWindow |end |begin | prog = irxevent | button = MENU | repeat = 3 | config = Key Return CurrentWindow |end |begin | prog = irxevent | button = RECORD | repeat = 3 | config = Key Return CurrentWindow |end |begin | prog = irxevent | button = RED | repeat = 3 | config = Key X CurrentWindow |end |begin | prog = irxevent | button = GREEN | repeat = 3 | config = Key I CurrentWindow |end |begin | prog = irxevent | button = YELLOW | repeat = 3 | config = Key bracketleft CurrentWindow |end |begin | prog = irxevent | button = BLUE | repeat = 3 | config = Key bracketright CurrentWindow |end |begin | prog = irxevent | button = BLANK | repeat = 3 | config = Key D CurrentWindow |end |begin | prog = irxevent | button = VOL- | repeat = 3 | config = Key Left CurrentWindow |end |begin | prog = irxevent | button = REV | repeat = 3 | config = Key Left CurrentWindow |end |begin | prog = irxevent | button = PLAY | repeat = 3 | config = Key P CurrentWindow |end |begin | prog = irxevent | button = MUTE | repeat = 3 | config = Key backslash CurrentWindow |end |begin | prog = irxevent | button = VOL+ | repeat = 3 | config = Key Right CurrentWindow |end |begin | prog = irxevent | button = FFW | repeat = 3 | config = Key Right CurrentWindow |end |begin | prog = irxevent | button = BACK/EXIT | repeat = 3 | config = Key Escape CurrentWindow |end |begin | prog = irxevent | button = FULL | repeat = 3 | config = Key Escape CurrentWindow |end |begin | prog = irxevent | button = PAUSE | repeat = 3 | config = Key P CurrentWindow |end |begin | prog = irxevent | button = 0 | config = Key 0 CurrentWindow |end |begin | prog = irxevent | button = 1 | config = Key 1 CurrentWindow |end |begin | prog = irxevent | button = 2 | config = Key 2 CurrentWindow |end |begin | prog = irxevent | button = 3 | config = Key 3 CurrentWindow |end |begin | prog = irxevent | button = 4 | config = Key 4 CurrentWindow |end |begin | prog = irxevent | button = 5 | config = Key 5 CurrentWindow |end |begin | prog = irxevent | button = 6 | config = Key 6 CurrentWindow |end |begin | prog = irxevent | button = 7 | config = Key 7 CurrentWindow |end |begin | prog = irxevent | button = 8 | config = Key 8 CurrentWindow |end |begin | prog = irxevent | button = 9 | config = Key 9 CurrentWindow |end | |I had to place the lircrc file as ~/.lircrc for irxevent to be able to |find in. In my logs I can see where lircd accepts the new client and |then disconnects it when I close mythfrontend but the remote doesn't |work at all in myth. | |Any ideas? | |--Dennis | | |------------------------- | |_______________________________________________ |mythtv-users mailing list |[email protected] |http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.2.6 (GNU/Linux) iD8DBQFB2QALinkYqF503K4RAsAAAJ4lOY9oYNxsC9kjnKEc6c5zWyhQNQCcCSo+ Z8zIR7e5G+vZVqyJhxRLy7o= =1hNX -----END PGP SIGNATURE----- |
_______________________________________________ mythtv-users mailing list [email protected] http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users
