On Sun, 2005-01-02 at 23:28 -0800, Scott Alfter wrote: > On Sun, Jan 02, 2005 at 11:59:36PM -0500, Dennis B. Hopp wrote: > > I've searched the archvies and the forums at http://forums.gentoo.org > > and I'm having a hell of time getting the Gray remote that came with my > > PVR-250 working. > > > > I followed the instructions here: > > > > http://gentoo-wiki.com/HARDWARE_Setup_MythTV > > > > When I do a make menuconfig I do not have any option to enable Linux > > Infrared controller. lircd is using /dev/lirc/0. If I cat /dev/lirc/0 > > and press buttons on the remote I get output on the screen (a bunch of > > garbage, but output none the less). irw doesn't seem to do anything > > > > my /etc/lircd.conf: > > > > begin remote > > > > name Hauppauge > > bits 13 > > flags SHIFT_ENC > > eps 30 > > aeps 100 > > > > one 950 830 > > zero 950 830 > > plead 960 > > gap 89584 > > repeat_bit 2 > > > > begin codes > > TV 0x000000000000100F > > RADIO 0x000000000000100C > > FULL_SCREEN 0x000000000000102E > > CH+ 0x0000000000001020 > > CH- 0x0000000000001021 > > VOL- 0x0000000000001011 > > VOL+ 0x0000000000001010 > > MUTE 0x000000000000100D > > SOURCE 0x0000000000001022 > > 1 0x0000000000001001 > > 2 0x0000000000001002 > > 3 0x0000000000001003 > > 4 0x0000000000001004 > > 5 0x0000000000001005 > > 6 0x0000000000001006 > > 7 0x0000000000001007 > > 8 0x0000000000001008 > > 9 0x0000000000001009 > > 0 0x0000000000001000 > > RESERVED 0x000000000000101E > > MINIMIZE 0x0000000000001026 > > end codes > > > > end remote > > If the gray remote that came with your PVR-250 is the same gray remote that > came with my PVR-350, your configuration is wrong. (IIRC, I ran across one > or two bad config files before I found the correct one.) Here's what I'm > using: > > begin remote > > name hauppaugegrey > bits 13 > eps 30 > aeps 100 > > one 0 0 > zero 0 0 > gap 200000 > min_repeat 4 > toggle_bit 2 > > > begin codes > OFF 0x00000000000017FD > GO 0x0000000000001FFB > 1 0x00000000000017C1 > 2 0x00000000000017C2 > 3 0x00000000000017C3 > 4 0x00000000000017C4 > 5 0x0000000000001FC5 > 6 0x0000000000001FC6 > 7 0x0000000000001FC7 > 8 0x0000000000001FC8 > 9 0x0000000000001FC9 > 0 0x00000000000017C0 > BACK/EXIT 0x00000000000017DF > MENU 0x0000000000001FCD > CH+ 0x00000000000017E0 > OK 0x00000000000017E5 > CH- 0x00000000000017E1 > VOL- 0x0000000000001FD1 > VOL+ 0x00000000000017D0 > RED 0x0000000000001FCB > GREEN 0x0000000000001FEE > YELLOW 0x00000000000017F8 > BLUE 0x0000000000001FE9 > MUTE 0x00000000000017CF > BLANK 0x0000000000001FCC > FULL 0x00000000000017FC > REW 0x0000000000001FF2 > PLAY 0x00000000000017F5 > FFW 0x0000000000001FF4 > RECORD 0x00000000000017F7 > STOP 0x0000000000001FF6 > PAUSE 0x00000000000017F0 > REPLAY 0x0000000000001FE4 > SKIP 0x00000000000017DE > end codes > > end remote
I put your config in and restarted lircd. lircd is running but when I use irw I still get no output. Is irw supposed to take any kind of command line option or something? --Dennis
_______________________________________________ mythtv-users mailing list [email protected] http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users
