Duhh ;) I ran alsactl -v and it said "alsactl version 1.0.7" I then did the resore and got this...
/usr/sbin/alsactl --file ~/asound.state restore /usr/sbin/alsactl: set_control:797: warning: numid mismatch (44/46) for control#44 /usr/sbin/alsactl: set_control:797: warning: numid mismatch (45/47) for control#45 /usr/sbin/alsactl: set_control:805: warning: name mismatch (Phone Playback Switch/PC Speaker Playback Switch) for control #46 /usr/sbin/alsactl: set_control:805: warning: name mismatch (Phone Playback Volume/PC Speaker Playback Volume) for control #47 /usr/sbin/alsactl: set_control:805: warning: name mismatch (Mic Playback Switch/Phone Playback Switch) for control #48 /usr/sbin/alsactl: set_control:805: warning: name mismatch (Mic Playback Volume/Phone Playback Volume) for control #49 /usr/sbin/alsactl: set_control:805: warning: name mismatch (Mic Boost (+20dB)/Mic Playback Switch) for control #50 /usr/sbin/alsactl: set_control:805: warning: name mismatch (Line Playback Switch/Mic Playback Volume) for control #51 /usr/sbin/alsactl: set_control:892: bad control.51.value type On Wed, 5 Jan 2005 12:53:43 -0800, Gregg Farhat <[EMAIL PROTECTED]> wrote: > I have ver 1.0.7, I will try the restore tomorrow night, along with > the change in the asoundrc. My device is 0,3. I will let you know > how it goes. > > -Gregg > > > On Wed, 05 Jan 2005 14:10:19 -0500, Kyle Rose <[EMAIL PROTECTED]> wrote: > > Gregg Farhat <[EMAIL PROTECTED]> writes: > > > > > I removed the suggested items and applied the .asoundrc. It still > > > has the same results. I did discover if I add -ac hwac3, -ao alsa9 > > > I get no sound on dvd, but if I remove it I get static. Any other > > > suggestions besides a hammer :) . Thanks again for your help. > > > > LOL, I almost did this once with a live because of this BS, but I > > doubt it would have helped. Keep the faith. :) It's a great sound > > card, especially given the very low cost. Given that I basically only > > ever use passthrough (except for playing Ogg/MP3 files, which are all > > 16 bit anyway), I doubt I will ever need anything different unless a > > non-S/PDIF digital interface appears. > > > > Which version of alsa are you running? I know I had problems with the > > different variants of 1.0.6, so make sure you're using 1.0.7 (not > > -rc?) or CVS. > > > > Also, try xine instead of mplayer. The alsa support on each piece of > > software is different, and frankly I've never gotten mplayer to work > > as reliably as xine even though xine's configuration seems more > > complicated at first. > > > > Next, how is your Live wired to your AC3 decoder? I use just the > > basic Live card with a coax connector going from (I believe) the white > > (left) channel on a stereo mini->RCA converter sitting in the top (?) > > mini jack, which on my card is gold instead of colored plastic, to the > > S/PDIF in on my receiver. I'm doing this from memory, so it's a bit > > fuzzy. > > > > Finally, try putting the attached asound.state into a file > > (e.g. /tmp/foo) and issuing "alsactl --file /tmp/foo restore". This > > is my mixer config. Since the Live has so many mixer settings that > > are so poorly documented, it took a lot of trial-and-error to get set > > up correctly. If this works for you, I'll post a web page indicating > > how to get this set up because I'll have positive confirmation that it > > works for at least one other person. :) This will *only* work with > > 1.0.7, because some of the mixer controls changed names, etc. > > > > Let me know what happens. I'm curious to hear if it works. > > > > Cheers, > > Kyle > > > > > > >
_______________________________________________ mythtv-users mailing list [email protected] http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users
