Thanks for the config file JJ, I tried the DISH remote one, but it is still the same. What remote code is that supposed to be on, the default (1)?
I think I'm going to have to build my own cable and ir blaster. I don't trust this one. Something is strange here. thanks, Pb On Sun, 16 Jan 2005 18:33:49 -0500, John Johnson <[EMAIL PROTECTED]> wrote: > Sorry I didn't reply sooner. Hope this helps! > > Regards, > JJ > > > > > On 16-Jan-2005, at 11:36, Paul Barrette wrote: > > > Hi John, > > yes, the expressvu box is the same as dish, I'm told. That would be > > great if you could send me your ledxmitd.conf. > > > > thanks, > > Pb > > > > > > On Sun, 16 Jan 2005 11:25:05 -0500, John Johnson <[EMAIL PROTECTED]> > > wrote: > >> (Assuming you're using a Dish Network box) > >> I wound up using a JVC file with a remote named JVC_RAW in it. > >> I can't find the file now, but I can email you my ledxmitd.conf if > >> you'd like. > >> > >> Regards, > >> JJ > >> > >> On 16-Jan-2005, at 10:46, Paul Barrette wrote: > >> > >>> Hi, > >>> I bought an irblaster from http://www.irblaster.info/, nice looking > >>> unit. I followed the irblaster howto to the letter, and everything > >>> seems to be working ok, BUT no channels change. > >>> -ledxmitd is logging events > >>> -infra red pulses coming out of the device when I run the > >>> change_channel scripts (I checked with a digital camera) > >>> -no channel changing at all!! > >>> -tried http://lirc.sourceforge.net/remotes/echostar/ > >>> -tried http://lirc.sourceforge.net/remotes/expressvu/ > >>> -tried http://lirc.sourceforge.net/remotes/dishnet/ > >>> > >>> I am starting to think that either some settings for my serial port > >>> are not right, or the irblaster is not the right one for the > >>> expressvu. > >>> > >>> The echostar DBS config looks like the right one. I am not sure what > >>> is meant by the following comment though: > >>> "You may have to play with the one/zero widths to get it working > >>> on a particular computer." (see below) > >>> > >>> I don't know what the one/zero settings should be or what they mean > >>> anyway. > >>> > >>> I think my param.h HZ setting is 1000. Is there another place to > >>> set > >>> this in the linux kernel? > >>> > >>> Any ideas would be appreciated, > >>> thanks, > >>> Pb > >>> > >>> > >>> # contributed by Jordan Hazen <[EMAIL PROTECTED]> > >>> # > >>> # brand: Echostar / DishNetwork > >>> # (ExpressVu) model no. of remote control: "blue-button" remote > >>> # set for codeset #6 supported devices: Most models of Echostar > >>> # IRDs: 2700, 4700, 5000 etc. Receiver must be set to a matching > >>> # remote codeset, per instructions in the manual. There are 16 > >>> # choices available, to avoid interference between nearby units. > >>> # I've recorded codes #6 (here) and #9. > >>> # > >>> # Pulse timing is more critical than usual for these receivers. > >>> # You may have to play with the one/zero widths to get it working > >>> # on a particular computer. A kernel compiled with HZ set to 1000 > >>> # or 1024 (rather than 100) is also helpful. > >>> > >>> I have changed the remote code set to #6 and #9, since the config > >>> offers both. > >>> -- > >>> Utque fit, in gremium pulvis si forte puellae > >>> Deciderit, digitis excutiendus erit: > >>> Etsi nullus erit pulvis, tamen excute nullum: > >>> Quaelibet officio causa sit apta tuo. (Ov. Ars 1.149ff.) > >>> _______________________________________________ > >>> mythtv-users mailing list > >>> [email protected] > >>> http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users > >> > >> > > > > > > -- > > Utque fit, in gremium pulvis si forte puellae > > Deciderit, digitis excutiendus erit: > > Etsi nullus erit pulvis, tamen excute nullum: > > Quaelibet officio causa sit apta tuo. (Ov. Ars 1.149ff.) > > > > -- Utque fit, in gremium pulvis si forte puellae Deciderit, digitis excutiendus erit: Etsi nullus erit pulvis, tamen excute nullum: Quaelibet officio causa sit apta tuo. (Ov. Ars 1.149ff.)
_______________________________________________ mythtv-users mailing list [email protected] http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users
