OK BusID "0:13:0" did the trick, and I think I'm much closer to getting this
to work.. but not quite there yet. Now when I try to load X, I get a
graphical black & white "X" which moves when I move the mouse, so I do get
output to my TV. However, The "X" just says there and X never finishes
loading. I get these errors:
IVTVDEV(0): FBIOBLANK: Invalid argument
IVTVDEV(0): FBIOPAN_DISPLAY: Invalid argument
IVTVDEV(0): FBIOBLANK: Invalid argument
IVTVDEV(0): FBIOBLANK: Invalid argument
Any ideas on how to get past this?
Thanks for everyone's help so far!
Shalem
--- Minh Duong <[EMAIL PROTECTED]> wrote:
The BusID thing varies. I've seen many variations. Try
BusID "0:13:0"
BusID "PCI:0:0xd:0"
BusID "0:0xd:0"
--- Shalem Shem-Tov <[EMAIL PROTECTED]> wrote:
From: Tim Fenn <[EMAIL PROTECTED]>
Reply To: Discussion about mythtv
<[email protected]>
To: Discussion about mythtv
<[email protected]>
Subject: Re: [mythtv-users] X to TVout on pvr350
Sent: Thursday, February 17, 2005 10:04 PM
On Thu, Feb 17, 2005 at 09:39:10PM -0500, Shalem
Shem-Tov wrote:
>OK having some problems getting X to TVout on
pvr350 (using Fedora C3). I >followed Jarod's HOWTO on how to change
xorg.conf
but once I did and tried >to reload X I got this error:
>
>Failed to load module "ivtvdev" (module does not
exist, 0)
>No drivers available
>
>
>ATrpms now has the ivtvdev driver in its own
package - this is a
>change that I don't think has made it into Jarod's
howto quite yet.
>Anyway, long story short:
>
>apt-get install ivtvdev
>
>should fix this (assuming you have Axel's repo
enabled).
>
>Regards,
>-Tim
Tim:
Thanks for the info, it help... to a point. Now
when I try loading X I get this error:
ivtvdev: No matching Device section for
instance (BusID PCI:0:13:0)
No devices detected.
/sbin/lspci -v gives me:
00:0d.0 Multimedia video controller: Internext
Compression Inc iTVC15 MPEG-2 Encoder(rev 01)
Subsystem: Hauppauge computer works Inc.
WinTV PVR-350
Flags: bus master, medium devsel, latency
64, IRQ 10
Memory at d8000000 (32-bit, prefetchable)
[size=64M]
Capabilities: [44] Power Management version
2
Any suggestions?
My xorg.conf is the same as before:
Section "Device"
Identifier "Hauppauge PVR 350 iTVC15
Framebuffer"
Driver "ivtvdev"
#Driver "fbdev"
### change fb0 to whatever your card grabbed
Option "fbdev" "/dev/fb1"
### change the BusID to whatever is reported
by lspci, specify it as hex.
BusID "0:0x0d:0"
EndSection
Thanks :)
> _______________________________________________
mythtv-users mailing list
[email protected]
http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users
__________________________________
Do you Yahoo!?
Read only the mail you want - Yahoo! Mail SpamGuard.
http://promotions.yahoo.com/new_mail
_______________________________________________
mythtv-users mailing list
[email protected]
http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users
