Josh... I used the source of the spin file from Johns site to build and burn the EEPROM with my Prom/EEProm VP-290 programmer, I did NOT install any of the special stuff on John board to load via serial or the special Parallax programmer card....
On Mon, Dec 8, 2014 at 6:39 AM, John Monahan <[email protected]> wrote: > All is explained here:- > > > http://s100computers.com/My%20System%20Pages/Console%20IO%20Board/Console%20IO%20Board.htm > > If not let me know > > John > > > > > > *From:* [email protected] [mailto:[email protected]] *On > Behalf Of *Crusty OMO > *Sent:* Monday, December 8, 2014 5:45 AM > *To:* [email protected] > *Subject:* RE: [N8VEM-S100:5789] Propeller Console board > > > > Hi John, > > I downloaded the CONSOLE IO files from the wiki site. > > Are there more files somewhere else? > Do I need to compile those "SPIN" files or is there a compiled binary file > somewhere else? > How do I program the Propeller chip? Does it require a special programmer? > or does it have a boot loader built into it? > How does my software use this console I/O board to send a character and > read the keyboard? > > Thanks, > Josh Bensadon > > > > ------------------------------ > > Date: Mon, 8 Dec 2014 08:24:29 -0500 > Subject: Re: [N8VEM-S100:5786] NKK Switches for Mini FP > From: [email protected] > To: [email protected] > > I would be interested > > Jim > > > > > > Sent via the Samsung Galaxy S™ III, an AT&T 4G LTE smartphone > > > > > -------- Original message -------- > From: Don Caprio <[email protected]> > Date: 12/07/2014 11:40 PM (GMT-05:00) > To: [email protected] > Subject: Re: [N8VEM-S100:5777] NKK Switches for Mini FP > > > Folks are starting to get the switches for the FP mini board and asking > about > a switch bracket. > > The switch bracket has two important purposes. One is for the > positioning of the > switches when you solder them in. I've tried doing this without a > bracket and it's > very difficult to get them lined up perfect without some sort of jig. > > I already have a quote from sheet metal fabricator here in town to > produce one. > In small quantities it was $15 USD. > > I'm thinking that I can do these on my mill, probably five or six at a > time for just the > cost of materials. I already have drill bits and tap for the tiny > screws. I'm going to give it > a try this week. > > If your interested in a bracket please let me know so I can gage the > interest level. > > We may be to produce a few and pass them onto other builders on a 'loaner' > basis. However my original plan was to use the bracket for installation > and as a > strain relief in the chassis. > > Please feel free to send along your ideas and suggestions. > > Thank you. > > > On 12/ 7/14 03:17 PM, G. Beat wrote: > > Before I setup the bench for assemblying this board, later this month, > > Did someone develop a switch frame (or std. Process) for maintainibg > alignment, as I solder these switches? > > > > -- > Don Caprio > [email protected] > > -- > You received this message because you are subscribed to the Google Groups > "N8VEM-S100" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > For more options, visit https://groups.google.com/d/optout. > > -- > You received this message because you are subscribed to the Google Groups > "N8VEM-S100" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > For more options, visit https://groups.google.com/d/optout. > > -- > You received this message because you are subscribed to the Google Groups > "N8VEM-S100" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > For more options, visit https://groups.google.com/d/optout. > > -- > You received this message because you are subscribed to the Google Groups > "N8VEM-S100" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > For more options, visit https://groups.google.com/d/optout. > -- ~~ _/) ~~~~ _/) ~~~~ _/) ~~~~ _/) ~~ Tom Lafleur -- You received this message because you are subscribed to the Google Groups "N8VEM-S100" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout.
