Re: [Nagios-users-br] NSClient++

[Leandro Grandini]

Fiz mais algumas tentativas mas é como se o serviço não carregasse.Eu verifiquei no gerenciador de serviços do Windows e lá informa que o serviço foi iniciado...   Tentei fazer um teste: ./check_nt -H 10.221.41.32 -p 12489 -v USEDDISKSPACE -l D -w 10 -c 5   E retornou o erro: Connection refused by host   Segue novamente o NSC.INI [modules] ;# NSCLIENT++ MODULES ;# A list with DLLs to load at startup. ;  You will need to enable some of these for NSClient++ to work. ; ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ; *                                                               * ; * N O T I C E ! ! ! - Y O U   H A V E   T O   E D I T   T H I S * ; *                                                               * ; ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! FileLogger.dll CheckSystem.dll CheckDisk.dll NSClientListener.dll NRPEListener.dll SysTray.dll CheckEventLog.dll ;CheckHelpers.dll ; ; CheckWMI IS AN EXTREM EARLY IDEA SO DONT USE FOR PRODUCTION ENVIROMNEMTS! ;CheckWMI.dll ; ; RemoteConfiguration IS AN EXTREM EARLY IDEA SO DONT USE FOR PRODUCTION ENVIROMNEMTS! ;RemoteConfiguration.dll   [Settings] ;# OBFUSCATED PASSWORD ;  This is the same as the password option but here you can store the password in an obfuscated manner. ;  *NOTICE* obfuscation is *NOT* the same as encryption, someone with access to this file can still figure out the ;  password. Its just a bit harder to do it at first glance. ;obfuscated_password=Jw0KAUUdXlAAUwASDAAB ; ;# PASSWORD ;  This is the password (-s) that is required to access NSClient remotely. If you leave this blank everyone will be able to access the daemon remotly. ;password=secret-password ; ;# ALLOWED HOST ADDRESSES ;  This is a comma-delimited list of IP address of hosts that are allowed to talk to the all daemons. ;  If leave this blank anyone can access the deamon remotly (NSClient still requires a valid password). ;allowed_hosts=127.0.0.1 allowed_hosts=10.221.40.22 ; ;# USE THIS FILE ;  Use the INI file as opposed to the registry if this is 0 and the use_reg in the registry is set to 1 ;  the registry will be used instead. use_file=1   [log] ;# LOG DEBUG ;  Set to 1 if you want debug message printed in the log file (debug messages are always printed to stdout when run with -test) debug=1 ; ;# LOG FILE ;  The file to print log statements to file=NSC.log ; ;# LOG DATE MASK ;  The format to for the date/time part of the log entry written to file. ;date_mask=%Y-%m-%d %H:%M:%S   [NSClient] ;# ALLOWED HOST ADDRESSES ;  This is a comma-delimited list of IP address of hosts that are allowed to talk to NSClient deamon. ;  If you leave this blank the global version will be used instead. allowed_hosts=10.221.40.22 ; ;# NSCLIENT PORT NUMBER ;  This is the port the NSClientListener.dll will listen to. port=12489 ; ;# BIND TO ADDRESS ;  Allows you to bind server to a specific local address. This has to be a dotted ip adress not a hostname. ;  Leaving this blank will bind to all avalible IP adresses. ;bind_to_address=   [Check System] ;# CPU BUFFER SIZE ;  Can be anything ranging from 1s (for 1 second) to 10w for 10 weeks. Notice that a larger buffer will waste memory ;  so don't use a larger buffer then you need (ie. the longest check you do +1). ;CPUBufferSize=1h ; ;# CHECK RESOLUTION ;  The resolution to check values (currently only CPU). ;  The value is entered in 1/10:th of a second and the default is 10 (which means ones every second) ;CheckResolution=10   [NRPE] ;# NRPE PORT NUMBER ;  This is the port the NRPEListener.dll will listen to. port=5666 ; ;# COMMAND TIMEOUT ;  This specifies the maximum number of seconds that the NRPE daemon will allow plug-ins to finish executing before killing them off. ;command_timeout=60 ; ;# COMMAND ARGUMENT PROCESSING ;  This option determines whether or not the NRPE daemon will allow clients to specify arguments to commands that are executed. allow_arguments=1 ; ;# COMMAND ALLOW NASTY META CHARS ;  This option determines whether or not the NRPE daemon will allow clients to specify nasty (as in |`&><'"\[]{}) characters in arguments. allow_nasty_meta_chars=1 ; ;# USE SSL SOCKET ;  This option controls if SSL should be used on the socket. ;use_ssl=1 ; ;# BIND TO ADDRESS ;  Allows you to bind server to a specific local address. This has to be a dotted ip adress not a hostname. ;  Leaving this blank will bind to all avalible IP adresses. ; bind_to_address= ; ;# ALLOWED HOST ADDRESSES ;  This is a comma-delimited list of IP address of hosts that are allowed to talk to NRPE deamon. ;  If you leave this blank the global version will be used instead. ;allowed_hosts=   [NRPE Handlers] ;# COMMAND DEFINITIONS ;# Command definitions that this daemon will run. ;# Can be either NRPE syntax: ;command[check_users]=/usr/local/nagios/libexec/check_users -w 5 -c 10 ;# Or simplified syntax: ;test=c:\test.bat foo $ARG1$ bar ;check_disk1=/usr/local/nagios/libexec/check_disk -w 5 -c 10 ;# Or even loopback (inject) syntax (to run internal commands) ;# This is a way to run "NSClient" commands and other internal module commands such as check eventlog etc. ;check_cpu=inject checkCPU warn=80 crit=90 5 10 15 ;check_eventlog=inject CheckEventLog Application warn.require.eventType=error warn.require.eventType=warning critical.require.eventType=error critical.exclude.eventType=info truncate=1024 descriptions ;check_disk_c=inject CheckFileSize ShowAll MaxWarn=1024M MaxCrit=4096M File:WIN=c:\ATI\*.* ;# But be careful: ; dont_check=inject dont_check This will "loop forever" so be careful with the inject command... ;# Check some escapings... ; check_escape=inject CheckFileSize ShowAll MaxWarn=1024M MaxCrit=4096M "File: foo \" WIN=c:\\WINDOWS\\*.*"   =============================================================================================== ----- Original Message ----- From: Jose Oliveira To: nagios-users-br@lists.sourceforge.net Sent: Monday, May 08, 2006 3:32 PM Subject: Re: [Nagios-users-br] NSClient++ Leandro Estou usando o NSClient++ em alguns servidores com Windows 2003 pois a versão que eu usava de NSClient não roda em Windows 2003. Ele está funcionando mais ou menos, ou seja, o serviço sobe beleza, algumas caracteristicas de segurança estão OK mas não consigo ler valores dos contadores do windows. Até mandei um emil para a lista HELP do projeto... Faça o seguinte teste: copie o software para uma pasta habilite o log instale o serviço dê partida no serviço tente usar. Se tiver erro, mande o log para nós... 2006/5/8, Leandro Grandini <[EMAIL PROTECTED]>: Estou tentando rodar este daemon em uma estação, mas aparentemente ele não está rodando.   Segue  o NSC.INI: ==================================================================================================== [modules] ;# NSCLIENT++ MODULES ;# A list with DLLs to load at startup. ;  You will need to enable some of these for NSClient++ to work. ; ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ; *                                                               * ; * N O T I C E ! ! ! - Y O U   H A V E   T O   E D I T   T H I S * ; *                                                               * ; ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! FileLogger.dll CheckSystem.dll CheckDisk.dll NSClientListener.dll NRPEListener.dll SysTray.dll CheckEventLog.dll ;CheckHelpers.dll ; ; CheckWMI IS AN EXTREM EARLY IDEA SO DONT USE FOR PRODUCTION ENVIROMNEMTS! ;CheckWMI.dll ; ; RemoteConfiguration IS AN EXTREM EARLY IDEA SO DONT USE FOR PRODUCTION ENVIROMNEMTS! ;RemoteConfiguration.dll   [Settings] ;# OBFUSCATED PASSWORD ;  This is the same as the password option but here you can store the password in an obfuscated manner. ;  *NOTICE* obfuscation is *NOT* the same as encryption, someone with access to this file can still figure out the ;  password. Its just a bit harder to do it at first glance. ;obfuscated_password=Jw0KAUUdXlAAUwASDAAB ; ;# PASSWORD ;  This is the password (-s) that is required to access NSClient remotely. If you leave this blank everyone will be able to access the daemon remotly. ;password=secret-password ; ;# ALLOWED HOST ADDRESSES ;  This is a comma-delimited list of IP address of hosts that are allowed to talk to the all daemons. ;  If leave this blank anyone can access the deamon remotly (NSClient still requires a valid password). ;allowed_hosts=127.0.0.1 allowed_hosts= 10.221.40.22 ; ;# USE THIS FILE ;  Use the INI file as opposed to the registry if this is 0 and the use_reg in the registry is set to 1 ;  the registry will be used instead. use_file=1   [log] ;# LOG DEBUG ;  Set to 1 if you want debug message printed in the log file (debug messages are always printed to stdout when run with -test) debug=1 ; ;# LOG FILE ;  The file to print log statements to file=NSC.log ; ;# LOG DATE MASK ;  The format to for the date/time part of the log entry written to file. ;date_mask=%Y-%m-%d %H:%M:%S   [NSClient] ;# ALLOWED HOST ADDRESSES ;  This is a comma-delimited list of IP address of hosts that are allowed to talk to NSClient deamon. ;  If you leave this blank the global version will be used instead. allowed_hosts=10.221.40.22 ; ;# NSCLIENT PORT NUMBER ;  This is the port the NSClientListener.dll will listen to. port=12489 ; ;# BIND TO ADDRESS ;  Allows you to bind server to a specific local address. This has to be a dotted ip adress not a hostname. ;  Leaving this blank will bind to all avalible IP adresses. ;bind_to_address=   [Check System] ;# CPU BUFFER SIZE ;  Can be anything ranging from 1s (for 1 second) to 10w for 10 weeks. Notice that a larger buffer will waste memory ;  so don't use a larger buffer then you need (ie. the longest check you do +1). ;CPUBufferSize=1h ; ;# CHECK RESOLUTION ;  The resolution to check values (currently only CPU). ;  The value is entered in 1/10:th of a second and the default is 10 (which means ones every second) ;CheckResolution=10   [NRPE] ;# NRPE PORT NUMBER ;  This is the port the NRPEListener.dll will listen to. port=5666 ; ;# COMMAND TIMEOUT ;  This specifies the maximum number of seconds that the NRPE daemon will allow plug-ins to finish executing before killing them off. ;command_timeout=60 ; ;# COMMAND ARGUMENT PROCESSING ;  This option determines whether or not the NRPE daemon will allow clients to specify arguments to commands that are executed. allow_arguments=1 ; ;# COMMAND ALLOW NASTY META CHARS ;  This option determines whether or not the NRPE daemon will allow clients to specify nasty (as in |`&><'"\[]{}) characters in arguments. allow_nasty_meta_chars=1 ; ;# USE SSL SOCKET ;  This option controls if SSL should be used on the socket. ;use_ssl=1 ; ;# BIND TO ADDRESS ;  Allows you to bind server to a specific local address. This has to be a dotted ip adress not a hostname. ;  Leaving this blank will bind to all avalible IP adresses. ; bind_to_address= ; ;# ALLOWED HOST ADDRESSES ;  This is a comma-delimited list of IP address of hosts that are allowed to talk to NRPE deamon. ;  If you leave this blank the global version will be used instead. ;allowed_hosts=   [NRPE Handlers] ;# COMMAND DEFINITIONS ;# Command definitions that this daemon will run. ;# Can be either NRPE syntax: ;command[check_users]=/usr/local/nagios/libexec/check_users -w 5 -c 10 ;# Or simplified syntax: ;test=c:\test.bat foo $ARG1$ bar ;check_disk1=/usr/local/nagios/libexec/check_disk -w 5 -c 10 ;# Or even loopback (inject) syntax (to run internal commands) ;# This is a way to run "NSClient" commands and other internal module commands such as check eventlog etc. ;check_cpu=inject checkCPU warn=80 crit=90 5 10 15 ;check_eventlog=inject CheckEventLog Application warn.require.eventType=error warn.require.eventType=warning critical.require.eventType=error critical.exclude.eventType=info truncate=1024 descriptions ;check_disk_c=inject CheckFileSize ShowAll MaxWarn=1024M MaxCrit=4096M File:WIN=c:\ATI\*.* ;# But be careful: ; dont_check=inject dont_check This will "loop forever" so be careful with the inject command... ;# Check some escapings... ; check_escape=inject CheckFileSize ShowAll MaxWarn=1024M MaxCrit=4096M "File: foo \" WIN=c:\\WINDOWS\\*.*" ====================================================================================================   Se alguém puder ajudar ou indicar alguma documentação, ficaria muito grato. Sem mais, Leandro Grandini -- Abraços JGeraldo