This is an old subject that I have collected bits and pieces of information on for quite some time. I have 2, thankfully no more than that, Vista Views in my 1976 31' Sovereign. They are located in the rear bedroom. As with the Vista Views in the 70 and later model trailers, the coating between the double pane glass has deteriorated. I have been waiting for the right time to proceed with the project of repairing the Vista Views along the lines covered in the instructions that were provided by Andy with Can-Am-RV a few years back.
> From: [EMAIL PROTECTED] > Subject Vista Views > > We have been fixing these windows using this > method for about 15 years with good success and no leaks. > > We have had a gasket material custom made to fill the space in the frame > when the inner glass is removed. This material costs $3.00 Canadian or > $2.00 U.S. per foot to purchase if you would like some you can order it > from Sandy ([EMAIL PROTECTED] am-RV.com or 800 709 2931) and have it shipped > UPS. You need the smaller size for snap ring windows and the larger for > windows without the snap ring on the inside. > > All of this is done without removing the aluminum frame from the > trailer thereby not disturbing the original caulking where the frame > fastens to the trailer shell. > > WEAR SAFETY GLASSES AND GLOVES. It does not happen very often but every > once in a while one of the outer safety glasses explodes, it will throw > glass 100' if it does. > > 1972: > The first year Double Pane Vista View Windows were available was 1972 > and these trailers actually had a plastic inner pane with its own frame. > So on a 72 you can remove the inner vista view pane and just clean off > the damaged tint on the inside of the outer pane. It is quit simple and > the finished product looks good. > > Snap ring windows; 1973 & 1974 a few early 75's > > These windows have an aluminum snap ring on the inside which is fairly > easy to remove. Once it is out you can pry out the plastic inner pane > and start cleaning out the caulking around the edges eventually you will > be able to push the outer pane through to the inside and remove it > completely. > > Clean the inside of the frame out completely and wipe it with a solvent > so that it is totally clean, make certain that the solvent does not run > down the outside of the unit and damage the lacquer. Next clean the > glass off completely (you can remove the remains of the old tint with a > razor blade) and wipe it off with a solvent such as lacquer thinner as > well. > > Coat all of the inside surfaces of the window frame with about a 1/8" > thick layer of silver silicone sealant. Take the clean glass and push > it into the silicone and then push in the rubber gasket(smaller size) > that will take up the extra space in the frame. Then all that is > necessary is to clean off the excess silicone on the inside and out and > let the remainder harden. The trailer should be kept dry for 6 hours > and not be towed for 48 hours. > > 1975-1984 Non Snap Ring Windows - Glass Inner Pane. > > These windows are the most difficult to do. The inner pane is glass set > in the gooiest caulking you have ever seen. First you need to break the > inner pane with a hammer and a screw driver near the edge, don't go > through and break the outer pane. The larger chunks of glass in the > middle will drop out easily but the small shards of glass stuck in the > caulking need to be pulled out one at a time with pliers. > > There is a soft plastic molding in the frame that goes from the outside > of the outer pane through to the inside of the frame, you will see a lip > of it on between the outer frame and the glass. Cut the lip off of the > outside by running a sharp knife all around the inside edge of the > frame. Then it you grab the molding on the inside with pliers you can > pull it out of the frame with the last of the glass pieces and the gooey > caulking. > > Unlike the snap ring windows the outer glass will not come out through > the inside frame so you need to clean the glass and the frame with it in > there loose. Clean the inside of the frame out completely and wipe it > with a solvent so that it is totally clean, make certain that the > solvent does not run down the outside of the unit and damage the > lacquer. Next clean the glass off completely (you can remove the > remains of the old tint with a razor blade) and wipe it off with a > solvent such as lacquer thinner as well. > > Coat all of the inside surfaces of the window frame with about a 1/8" > thick layer of silver silicone sealant. Take the clean glass and push > it into the silicone and then push in the rubber gasket (larger size) > that will take up the extra space in the frame. Then all that is > necessary is to clean off the excess silicone on the inside and out and > let the remainder harden. The trailer should be kept dry for 6 hours > and not be towed for 48 hours. > > > There you have it. It is not a job for the faint hearted but it is more > tedious than difficult. When it is done with the rubber gasket in place > it looks professional, like the factory made it that way. Of course my 1976 has the type of Vista Views that require breaking the inner pane of glass and is probably why I have put the project off. My question has anyone done its in a 1976 or later model Airstream. If so what were the results and are there pictures available of the steps involved. Thanks for the input Don Hardman 1976 31' Sovereign To unsubscribe from this group, go to http://www.groups.yahoo.com/group/AirstreamList/ and unsubscribe. To suspend delivery while traveling, simply change the delivery option to No Mail-Web only. Yahoo! Groups Links <*> To visit your group on the web, go to: http://groups.yahoo.com/group/AirstreamList/ <*> To unsubscribe from this group, send an email to: [EMAIL PROTECTED] <*> Your use of Yahoo! Groups is subject to: http://docs.yahoo.com/info/terms/
