I haven't used those specfic units so can't help with the connectors. Don't 
worry about the seeming triviality, I think everyone on here loves to see those 
digits light up and change.
  ----- Original Message ----- 
  From: Dylan Distasio 
  To: [email protected] 
  Sent: Friday, November 25, 2011 4:14 PM
  Subject: Re: [neonixie-l] Question on Russian IN-14 kit


  Thanks for the comments.  It might be a good exercise for me to wire up a PIC 
or something similar.  I've been looking for a project to do some actual 
perfboarding versus a kit PCB, and it would let me do some PIC programming 
which I haven't done yet.


  One other question if you actually have built one of these specific units.  
Any suggestions on connectors for the pins?  They're kind of rectangular.  I 
soldered some wires directly to one of the units just to test it out and play 
with the 74141 logic table but I'd like to find a connector to slip on.  


  All the nixies I've built up until now were from kits or using an ardunix or 
arduino with existing code so I haven't had to look at the truth table until 
now.  I had fun watching the digits change based on which inputs I was setting 
high.  I realize it's trivial, but it's exciting for someone still learning the 
basics.  


  On Fri, Nov 25, 2011 at 10:44 AM, Nigel Walker <[email protected]> 
wrote:

    I just use the brute force method of using a 40 pin DIL PIC. Nice and easy.

    Nigel.

      ----- Original Message ----- 
      From: Dylan Distasio 
      To: [email protected] 
      Sent: Friday, November 25, 2011 3:37 PM
      Subject: [neonixie-l] Question on Russian IN-14 kit


      Hi all- 


      I picked up a Russian nixie tube kit on eBay which I just received.  It's 
got 6 IN-14s, each wired to a separate PCB with a 74141 on each board.  I'm not 
sure if anyone on list has built one of these before, but I wondered if anyone 
has any tips for controlling all 6 digits for a clock without needing to 
control 4 separate inputs on each 74141 individually.  I will have to set 24 
different inputs this way to control the clock digits.  I realize I will have 
to wire them up either way, but was hoping there might be a trick to reducing 
the number of unique input signals I need to manage with a microcontroller of 
some sort.  I am still a beginner with multiplexing.  I am familiar with it 
from the Arduinix and other designs but since each tube has its own chip I'm 
not sure what the best approach is.  I'm still a beginner so I am probably 
missing something obvious.


      Thanks,
      Dylan

      -- 
      You received this message because you are subscribed to the Google Groups 
"neonixie-l" group.
      To post to this group, send an email to [email protected].
      To unsubscribe from this group, send email to 
[email protected].
      For more options, visit this group at 
http://groups.google.com/group/neonixie-l?hl=en-GB.


    -- 
    You received this message because you are subscribed to the Google Groups 
"neonixie-l" group.
    To post to this group, send an email to [email protected].
    To unsubscribe from this group, send email to 
[email protected].
    For more options, visit this group at 
http://groups.google.com/group/neonixie-l?hl=en-GB.




  -- 
  You received this message because you are subscribed to the Google Groups 
"neonixie-l" group.
  To post to this group, send an email to [email protected].
  To unsubscribe from this group, send email to 
[email protected].
  For more options, visit this group at 
http://groups.google.com/group/neonixie-l?hl=en-GB.

-- 
You received this message because you are subscribed to the Google Groups 
"neonixie-l" group.
To post to this group, send an email to [email protected].
To unsubscribe from this group, send email to 
[email protected].
For more options, visit this group at 
http://groups.google.com/group/neonixie-l?hl=en-GB.

Reply via email to