I have used 6pcs 74141 with a single 16F627A - total of 14 I/O pins (excluding 
Quartz X-Tal)

The approach was as follows - I used 3pcs 74LS373 registers to maintain the 
outputs. All PORTB pins from the PIC were used to drive the registers (8 bits) 
while 3 PORTA pins were used to SELECT the registers. Unfortunatelly I have 
never drawn a proper schematic for my "design". It was also built on perfboard 
but it is running for two years now. Also the powersupply was built using a 
separate (and very cheap) 12F508 PIC instead of a 555. No fancy PWM, just a 
simple impluse train (is this the correct term? I am not an English native) 
stopped when Voltage reaches a certain level.
I might add that I had no prior electronic experience (except a few childhood 
projects), however I am familiar with programming, so using a uC instead of a 
555 seemed easier. And I had an ambition to do all design (HW+SW) by myself, 
even though it might prove less efficient/fancy and more time consuming. I 
*would* recommend this approach rather than blindly following step-by-step 
instructions.

If one requires more info I would be glad to provide. Also I have seen that 
many people on this list (with far more experience than myself) could provide 
the right pointers or hints.
Success!
Mihai


On Nov 25, 2011, at 6:40 PM, Nigel Walker wrote:

> I haven't used those specfic units so can't help with the connectors. Don't 
> worry about the seeming triviality, I think everyone on here loves to see 
> those digits light up and change.
> ----- Original Message -----
> From: Dylan Distasio
> To: [email protected]
> Sent: Friday, November 25, 2011 4:14 PM
> Subject: Re: [neonixie-l] Question on Russian IN-14 kit
> 
> Thanks for the comments.  It might be a good exercise for me to wire up a PIC 
> or something similar.  I've been looking for a project to do some actual 
> perfboarding versus a kit PCB, and it would let me do some PIC programming 
> which I haven't done yet.
> 
> One other question if you actually have built one of these specific units.  
> Any suggestions on connectors for the pins?  They're kind of rectangular.  I 
> soldered some wires directly to one of the units just to test it out and play 
> with the 74141 logic table but I'd like to find a connector to slip on.  
> 
> All the nixies I've built up until now were from kits or using an ardunix or 
> arduino with existing code so I haven't had to look at the truth table until 
> now.  I had fun watching the digits change based on which inputs I was 
> setting high.  I realize it's trivial, but it's exciting for someone still 
> learning the basics.  
> 
> On Fri, Nov 25, 2011 at 10:44 AM, Nigel Walker <[email protected]> 
> wrote:
> I just use the brute force method of using a 40 pin DIL PIC. Nice and easy.
>  
> Nigel.
>  
> ----- Original Message -----
> From: Dylan Distasio
> To: [email protected]
> Sent: Friday, November 25, 2011 3:37 PM
> Subject: [neonixie-l] Question on Russian IN-14 kit
> 
> Hi all-
> 
> I picked up a Russian nixie tube kit on eBay which I just received.  It's got 
> 6 IN-14s, each wired to a separate PCB with a 74141 on each board.  I'm not 
> sure if anyone on list has built one of these before, but I wondered if 
> anyone has any tips for controlling all 6 digits for a clock without needing 
> to control 4 separate inputs on each 74141 individually.  I will have to set 
> 24 different inputs this way to control the clock digits.  I realize I will 
> have to wire them up either way, but was hoping there might be a trick to 
> reducing the number of unique input signals I need to manage with a 
> microcontroller of some sort.  I am still a beginner with multiplexing.  I am 
> familiar with it from the Arduinix and other designs but since each tube has 
> its own chip I'm not sure what the best approach is.  I'm still a beginner so 
> I am probably missing something obvious.
> 
> Thanks,
> Dylan
> 
> -- 
> You received this message because you are subscribed to the Google Groups 
> "neonixie-l" group.
> To post to this group, send an email to [email protected].
> To unsubscribe from this group, send email to 
> [email protected].
> For more options, visit this group at 
> http://groups.google.com/group/neonixie-l?hl=en-GB.
> 
> -- 
> You received this message because you are subscribed to the Google Groups 
> "neonixie-l" group.
> To post to this group, send an email to [email protected].
> To unsubscribe from this group, send email to 
> [email protected].
> For more options, visit this group at 
> http://groups.google.com/group/neonixie-l?hl=en-GB.
> 
> 
> -- 
> You received this message because you are subscribed to the Google Groups 
> "neonixie-l" group.
> To post to this group, send an email to [email protected].
> To unsubscribe from this group, send email to 
> [email protected].
> For more options, visit this group at 
> http://groups.google.com/group/neonixie-l?hl=en-GB.
> 
> -- 
> You received this message because you are subscribed to the Google Groups 
> "neonixie-l" group.
> To post to this group, send an email to [email protected].
> To unsubscribe from this group, send email to 
> [email protected].
> For more options, visit this group at 
> http://groups.google.com/group/neonixie-l?hl=en-GB.

-- 
You received this message because you are subscribed to the Google Groups 
"neonixie-l" group.
To post to this group, send an email to [email protected].
To unsubscribe from this group, send email to 
[email protected].
For more options, visit this group at 
http://groups.google.com/group/neonixie-l?hl=en-GB.

Reply via email to